Having regard to the text of the minutes where the changes in the salary level and definitions of several professional categories are approved, as well as the creation of new ones, corresponding to the evaluation of the second half of 2006 of the company Fabrica Nacional de Moneda y Timbre-Real Casa de la Moneda (Convention Code number 90002052011987), minutes which were signed on 18 October and 18 November 2010 by the Joint Commission of Valuation of which they are part representatives of the management of the company and the business committee representing the entity and the workers of the same to the one that is accompanied by favorable report issued by the Ministries of Economy and Finance and of the Presidency (Executive Committee of the Inter-Ministerial Commission of Retributions), in compliance with the previewed Law 26/2009, of 23 December, of the General Budget of the State for 2010, and in accordance with the provisions of Article 90 (2) and (3) of the Royal Legislative Decree 1/1995 of 24 March, approving the recast of the Law of the Staff Regulations, and Royal Decree 713/2010 of 28 May on the registration and deposit of agreements and collective work agreements,

This Work General Address resolves:

First.-To order the registration of the aforementioned Acts in the corresponding Register of agreements and collective agreements of work with operation through electronic means of this Steering Center, with notification to the Commission Negotiating with the warning to the same of the mandatory compliance of Law 26/2009, of December 23, of the General Budget of the State for the year 2010, with the execution of those Agreements.

Second. -Dispose your publication in the "Official State Bulletin".

Madrid, 9 February 2011. -Director General of Labour, Raul Riesco Roche.

Final Act:

Address Representatives:

Ms Marta Bedoya Castro.

Ms Carmen Martín Sierra (advisor).

Workers ' Representatives:

D. Antonio Santiago Morales.

D. Juan Manuel Camara Diaz (advisor).

In Madrid, on 18 October 2010, the members of the Joint Committee on Valuation are meeting, drawing up this final report, which sets out the results of the assessment of the employment positions of the Joint Committee. Second half of 2006.

Posts valued or reviewed at the request of the departments.

Positions that go up level.

Operational Staff:

Balas ' Rompedan Machinist. Paper Factory: 6.

Official 1. Electronic Electrical Outstanding Maintenance. Maintenance: 11.

Posts that do not go up level.

Operational Staff:

Legiate and Blanking machines. Paper Factory: 7.

Smart Card Encarted Milling Machine. Printing: 9.

Passport Machinist. Printing: 10.

Official 1. Mics Maintenance Featured. Maintenance: 11.

Passport Assistant. Printing: 7.

Reviewed posts per claim of their occupants.

Posts that do not go up level.

Operational Staff:

Officer 1. Mme Maintenance Machines. Maintenance: 9.

Reviewed posts by claim of their occupants with no agreement on any factor.

The following jobs have not been valued for no agreement on whether or not the claim submitted implies a review of the assessment of the claim, as reflected in the daily minutes:

Computer Analyst. Information Systems.

Officer 1. of Telas. Paper Factory.

Officer 1. Chief of the Rotary Machine Team of Seals. Doorbell.

According to Article 9 of the current Collective Agreement, the positions of disagreement will be submitted to arbitration, agreeing that it is the Provincial Labour Inspectorate who will carry out the agreement, accepting both of them. representations of the report issued by the Inspectorate. These posts are:

Computer Analyst. Information Systems.

Officer 1. of Telas. Paper Factory.

Officer 1. Chief of the Rotary Machine Team of Seals. Doorbell.

Multiple:

Person relationship and effect date.

The relationship of the staff affected by this review and the dates of application is published internally in the FNMT-RCM's work centers.

All valuations will be applied once the mandatory ministerial authorization is obtained and published in the "BOE" as an integral part of the Collective Agreement and with the effects of the aforementioned application dates.

Bullet-breaking machine.

It is the operator who, with full knowledge of his profession, has as mission the handling of the installation that supplies the cotton wipe for the manufacture of paper. It will have to make all the necessary adjustments, transport and supply of raw materials, waste removal, monitoring of the correct operation of the machine and attention to the auxiliary systems, including control and safety, for the obtaining the erases in accordance with the requirements of the production. For which you will perform the following functions:

Preparation and loading of the machine, transport of bullets with transport-lift truck and removal of waste to the places established for this purpose, taking responsibility for the process and making the necessary adjustments for the obtaining correct quality and production.

Attention, monitoring and control of the various systems that form the installation that supplies the cotton wipe for paper making.

Entertainment of the machine and silos, resolution of small breakdowns and cleaning of all its elements and area of action, as well as the supervision and regulation of the clearing system, putting in knowledge of its the need for repairs in the area where they perform their work. It shall also carry out the transport and placing of bullets in the warehouse, if necessary, following the guidelines established by the person responsible for the transport.

Completing the forms required for your job.

Official 1. electrical outstanding maintenance officer:

It is the operator who, with full knowledge of his profession, performs preventive and corrective maintenance, as well as the implantation, reform or improvement of any machine, element, system or installation in the FNMT-RCM or out of In its electrical or electronic and in addition mechanical, hydraulic and pneumatic aspects on the cutting, sorting and packaging machines according to plans, drawings, technical specifications or verbal instructions, taking responsibility for its correct execution, having to know the English language, in order to understand related terms with your work, for which you will perform the following functions:

Localization, diagnosis (either by itself and/or in collaboration with staff of its specialty, other specialties or other than the FNMT-RCM) and repair of all types of electronic breakdowns (analog or digital), in any of the machines, elements, systems or installations, with the help of the tools, tools and appliances of their profession, keeping the machine, element or system the shortest possible time out of service.

Dismantling, cleaning, repairing or replacing the element, mounting, adjusting and adjusting to achieving its perfect performance, including repairs and small modifications of pneumatic systems, lifting the schemas and sketches necessary, interpretation of electrical, electronic, pneumatic, mechanical and hydraulic planes, as well as the replacement, adjustment and verification of simple mechanical elements, according to the current regulations.

Location, diagnosis and resolution of breakdowns, implantation, reformation or improvement of electrical, electronic, mechanical, hydraulic and pneumatic elements or installations on the cutting, sorting and packaging machines, unmounting, cleaning and repairing the broken-down element, requesting necessary spare parts and building or adapting the necessary parts. Interpretation of electrical, electronic, mechanical, hydraulic and pneumatic planes.

Making or modifying the control and control programs of PLC's, CNC's and other existing hardware devices in Fabrica, for adaptation to the FNMT-RCM equipment in implementation of reforms or improvements.

Design of electrical, electronic and pneumatic circuits and on the cutting, selection and packaging machines also mechanical and hydraulic.

Performing preventive maintenance operations according to instructions or bulletins, which you must complete, warning of any special or systematic defects that you detect.

Proposal for your immediate superior acquisition of materials, spare parts, tools and tools that you consider necessary, based on inventory or catalogues.

Building or adapting simple parts that you may need in your work development.

Use of auxiliary tools and machines for their maintenance, preservation and transport, as well as for their cleaning and the area of operation.

Assistance and supervision of 2. Officers who collaborate with him in his duties, directing operations and resolving doubts that may arise. It also resolves doubts to the different production workers regarding the change of spare parts, positioning or actuation of electrical, electronic or pneumatic elements of their work area, as well as mechanical and hydraulic in the cutting, sorting, and packaging machines.

Collaborates with its superiors in preparing jobs and checking spare parts, completing and updating technical documentation, as well as in various maintenance studies.

Completing the documentation required for job development.

Leaching and bleaching machines:

It is the operator who with full knowledge of his profession and under the coordination of the Head of the Cycling and Preparation Team of Pastas, is entrusted with the attention of the process of bleaching and monitoring of the installation that supplies the cotton wipe for paper making. It must make precise corrections, supply and unloading of blocks by means of forklift, incorporation of chemicals, attention to auxiliary systems, including control and safety and all the operations necessary to obtain the product in accordance with established standards or guidelines marked by its immediate superior. For which you will perform the following functions:

Review at the start of the day of all items and machinery by checking their readiness for proper operation.

Preparation, loading and monitoring of the bleaching process, incorporation of the products provided for each case according to established standards, washing and discharge of wastewater and extraction of specimens for analysis, being responsible for obtaining a correct quality and production. Centrifuge of the blocks of erases, carrying out the appropriate checks and corrections.

Attention to the installation that supplies the cotton wipe for paper making, carrying out rearmament tasks of the same and starting up in case of a stop.

Entertainment of machines and resolution of small breakdowns. Performance of the passivate according to the facilitated method, as well as the cleaning of filters, tanks, all its elements and area of action. Assisting Maintenance staff in repairs, whenever required.

Fulfillment of all the forms required in relation to your work.

Monitoring the work of the Pastas and Cicside Preparation Assistant when collaborating with him in his/her duties, directing and resolving doubts that may be presented to him and monitoring the block compacting machine during the Established breaks of this.

Milling Machine-Embodied Smart Cards:

It is the operator who, with full knowledge of the equipment in charge, has as mission the milling, die-cutting, numeral, micromodule laminate, face, prepersonalisation and customization of cards. It shall carry out the preparation, commissioning and attention of equipment and ancillary systems, including control and safety systems, by making the necessary corrections to obtain the product in accordance with the conditions required. For which you will perform the following functions:

Preparation and commissioning of auxiliary machines and equipment according to established guidelines. Introduction of the necessary data, adjustment and positioning of the mechanical elements.

Sourcing and preparing the precise materials for the development of your work. Commissioning of the equipment, selection and introduction of the different parameters in the control programmes, making the appropriate modifications to the control programmes.

Power of machines and attention to correct operation, solving errors, calls and interference that occur in different phases and being responsible for correct quality and production.

Qualitative and quantitative verification of the product, performing the quality controls that you have established, entering the data in a computer program and completing the control forms required.

Performing elementary maintenance tasks, cleaning the elements of the machines and acting area, collaborating with maintenance personnel on repairs whenever required.

Passport machine:

It is the operator who, with the capacity of coordination, full knowledge of the position and the lines and machinery for the manufacture of passports, can drive any of those assigned to obtain the product of In accordance with the conditions required, with the responsibility for its correct quality and production, training and information must also be provided to the workshop operators who need it. For which you will perform the following functions:

Preparation and commissioning of lines, machinery and auxiliary systems, supply, preparation and loading of materials, either on itself or through manual pallet trucks, whether mechanical or electrical.

Serves and monitors the operation of lines and machinery, as well as auxiliary systems, control and customization devices, including checking and security, addressing errors and interference that occur, by adjusting, correcting, and synchronizing the different elements and systems to achieve the correct product finish.

To carry out process operations manually in passports which, due to their special characteristics, require it, as they may be: introduction of one-on-one, manual-fold, folding, gluing, stacking, cut, etc.

Qualitative verification of the products that are incorporated into the lines and machinery, control of the products during the process and at the end of each one, checking the possible errors of reading on the monitors, the numbering and customization in the corresponding line, solving the incidents that can occur. Random review of production by template if required.

Replacement and adjustment of parts and parts that do not require the presence of specialized personnel, sharpening of blades and supports, entertainment, resolution of small breakdowns, greases and cleaning of the various elements and performance area, assisting the Maintenance staff, as long as required.

Coordination and monitoring of the work of the assistant who collaborates with him in his or her duties, replacing him periodically, or during the established breaks, at the departure of the lines.

Fulfillment of the control forms related to your work, generating the production listings that are required for you.

The theoretical-practical training of the workshop operators about the tasks to be performed and the machinery to be used, solving all those doubts that may arise in the development of their work.

Officer 1. Mechanical Maintenance Highlighted:

It is the operator who, with full knowledge of his profession, performs preventive and corrective maintenance as well as the implantation, reform or improvement of any machine, element, system or installation in the FNMT-RCM or out of In its mechanical, hydraulic or pneumatic and in addition electrical and electronic aspects in the cutting, sorting and packaging machines, according to drawings, drawings, technical specifications or verbal instructions, the English language must be known, in order to understand terms related to your work, maintaining the element or Machine off-duty machine the time strictly necessary and being responsible for its proper execution. For which you will perform the following functions:

Location, diagnosis (either by itself, and/or in collaboration with staff of its specialty, other specialties, or non-FNMT personnel) and resolution of all types of breakdowns, interpreting plans and helping them tools and apparatus for the measurement of the profession, including electronic and electronic equipment for diagnosis. Disassembly, cleaning, repair or replacement of the element, replacement of the basic electrical elements, assembly, welding, adjustment and adjustment, including tracing, marking and finishing to achieve its perfect performance.

Implantations, reforms, improvements, disassembly, transport, assemblies, adjustments, adjustments and putting of machinery according to the current regulations, taking responsibility for its correct execution and carrying out those drawings of pieces that are required as well as the design of mechanical elements and manoeuvring design in hydraulic and pneumatic circuits.

Location, diagnosis and resolution of breakdowns, implantation, reformation or improvement of mechanical, hydraulic, pneumatic, electrical and electronic elements or installations on the cutting, sorting and packaging machines, unmounting, cleaning and repairing the broken-down element, requesting necessary spare parts and making or modifying the control and control programs for PLC's, CNC's and other hardware devices, lifting the electrical schemes to be specified.

Tailoring preventive and predictive maintenance bulletins for your craft.

Conducting preventive maintenance operations according to instructions or bulletins, which you must complete, warning of any special or systematic defects that you detect.

Proposal for your immediate superior acquisition of materials, spare parts, tools and tools that you consider necessary, based on inventory or catalogues.

Construction or adaptation of all kinds of parts you may need to carry out your repairs. Recovery and cleaning of items and consumable materials of possible use in subsequent repairs and modifications.

Resolution of doubts that may arise for production workers in their field of work in exchange for spare parts, positioning or actuation of mechanical, pneumatic or hydraulic and in addition electrical and electronic on the cutting, sorting, and packaging machines.

Use of auxiliary tools and machines, dealing with their transport, maintenance and conservation, as well as their cleanliness and the area of action.

Assistance and supervision of officers 2. who collaborate with him in their duties, directing their operations and resolving doubts that may be presented to them.

Collaborates with its superiors in preparing the works, completing and updating technical documentation, verification of spare parts and various maintenance studies.

Fulfillment of all documentation necessary for the development of your work.

Passport helper:

It is the operator who, with sufficient knowledge of the process, the lines and machinery for the manufacture of passports, and under the coordination of the driver, has as main mission the verification of the correct finishing of the product, collaborating with the driver in his/her duties. For which you will perform the following functions:

Sourcing, preparation, removal and loading of materials, on itself or by manual, mechanical or electrical transpalette.

Review of guards by checking their measurements and detecting possible anomalies, random checking of the typographical and perforated numbering, verifying the possible errors of reading the line, and generating a list of changes.

Qualitative and quantitative verification of the product carrying out a self-control in the phases of the established process: position of the elements that compose it, stamping, sizing, numbering, verification of the state of the passports and correction of vices, etc., in accordance with the requirements required, carrying out the necessary operations for its completion.

Attention to the operation of the lines and machinery, feeding of the chargers and resolution of the interferences following the guidelines received from the driver, when replaced by this periodically or in the Established breaks.

Entertainment, replacement of elements, repair of small breakdowns and cleaning of machines and area of action.

Collaborates with the driver in all his/her duties, following his/her guidelines, as well as with maintenance personnel on repairs, whenever required.

Final Act.

Address Representatives:

Ms Marta Bedoya Castro.

Ms Carmen Martín Sierra (advisor).

Workers ' Representatives:

D. Antonio Santiago Morales.

D. Juan Manuel Camara Diaz (advisor).

In Madrid, on 18 November 2010, the members of the Joint Committee on Valuation are meeting, drawing up this final act, where the results of the assessment of the relevant jobs are collected. the second semester of 2006, which were submitted to the arbitration of the Provincial Labour Inspectorate.

Reviewed posts per claim of their occupants.

Posts that will not be valued for no change of functions:

Computer Analyst. Information Systems.

Officer 1. of Telas. Paper Factory.

Officer 1. Chief of the Rotary Machine Team of Seals. Doorbell.

Multiple:

All valuations will be applied once the mandatory ministerial authorization is obtained and published in the "BOE" as an integral part of the Collective Agreement and with the effects of the aforementioned application dates.