Amendments To The Cabinet Of Ministers On 16 September 2003, Regulations No. 518 "pressure Equipment For Complex Technical Procedures For Supervision"
Original Language Title: Grozījumi Ministru kabineta 2003.gada 16.septembra noteikumos Nr.518 "Spiedieniekārtu kompleksu tehniskās uzraudzības kārtība"
Read the untranslated law here: https://www.vestnesis.lv/ta/id/107096
Cabinet of Ministers Regulations No. 284 in Riga in 2005 (April 26. No 23 14) amendments to the Cabinet of Ministers on 16 September 2003, regulations No. 518 "pressure equipment complex of technical supervision order Issued in accordance with the law" on technical supervision of dangerous equipment, "the second part of article 3 to make a Cabinet of 16 September 2003, the provisions of the" Pressure equipment no 518 complex technical procedures for supervision "(Latvian journal, 2003, 129 no) the following amendments: 1. Replace the text, the words" the competent notified body inspection "(fold) with the words" inspection body "(fold). 2. Express 2.2. subparagraph by the following: "2.2. portable fire-fighting tanks and breathing tanks or pressure equipment package;". 3. Supplement with 2.20. bottom point as follows: "2.20. warm water (if the temperature does not exceed 110 ° C) pressure equipment intended for the manufacture of complex where the solid fuel is fed by hand, when the complex capacity of less than 500 kW." 4. Express 4 by the following: "4. The Ministry of economy in cooperation with the relevant technical standards Committee recommends limited liability company" Latvian standards "in connection with these terms, reliance and designing standard applicable list." 5. Delete paragraph 5, the words "non-profit organization". 6. To complement the chapter 1 to 5.1 and 5.2 as follows: "5.1 pressure equipment complex technical inspection in accordance with Chapter 4 of these rules is entitled to take an accredited institution, for which the economic Ministry has published a notice in the newspaper" Gazette "(further-the inspection body), if it is: 5.1 1. Latvian National Accreditation Bureau confirmed the inspection body responsibilities pursuant to the standard LVS EN ISO/IEC 17020:2005" the main criteria for the different types of institutions carrying out the inspection criteria "; 2. insure your 5.1 civil liability of an amount to cover the possible losses incurred by mistake, calculated business areas risk assessment in cooperation with the institutions chosen insurer. 5.2 the Latvian National Accreditation Bureau, which has been rated by the inspection bodies, the inspection body shall conduct regular checks on the conformity of this provision with the requirements laid down in paragraph 5.1. " 7. Make paragraph 8 by the following: ' 8. Each pressure equipment package needs a passport in the national language. Passport to the particular complex pressure equipment in accordance with the provisions of the model Passport set out in annex a of the possessor of complex pressure equipment fill in who initiated the use of the equipment in Latvia. " 8. Make the introductory paragraph 10 by the following: "the possessor of complex pressure equipment 10. the Passport accompanied by a declaration of conformity, which was drawn up under the Cabinet of Ministers of 2 May 2000, the Regulation No 165" provisions of the pressure equipment directive and the assemblies, as well as the Assembly and operating instructions in the language of the country. The instructions shall include at least the following information: ". 9. Express 13.1. subparagraph by the following: "13.1. provide pressure equipment complex enough to service personnel who trained and instructed in accordance with the laws and regulations on the protection of health, the use of work equipment, and job training in matters of protection, taking into account the equipment design and usage conditions;". 10. Express 13.4. subparagraph by the following: "13.4. ensure passports and the complex pressure equipment instructions for use storage and reporting of national labour inspection officers and representatives for the inspection bodies of the specified regulations;". 11. Express 13.6 paragraph as follows: "to provide a complex pressure equipment 13.6 timely technical checks;". 12. Supplement with 13.1 points by the following: "13.1 If a possessor of complex pressure equipment change its structure or main technical parameters, they are obligated to match it with the inspection authority shall make a record of a complex pressure equipment in the technical passport. If the changes are significant, the possessor shall ensure compliance of the pressure equipment complex Cabinet 2 May 2000 No. 165 of the provisions of the "pressure equipment directive and the rules package" requirements. " 13. Amend section 16.2.4. the words "direct action". 14. Add to paragraph 38 of the complex after the words "pressure equipment" with the words "elements and". 15. Express 45 as follows: "45. Pressure equipment complex routine technical inspections and emergency technical inspection this provision in paragraph 56 cases made inspection institution in accordance with the applicable standards and requirements of this chapter." 16. To supplement the rules with 45.1 points as follows: "the institution of pressure equipment Inspections of 45.1 complex hydraulic sealed at the time of testing security device." 17. Make 47 by the following: "47. the content of the technical examination of complex pressure equipment, storage of LPG, shall be determined in accordance with the applicable requirements of the standards. Hydraulic or internal inspections are carried out at intervals not exceeding 12 years. " 18. To supplement the provisions of the following paragraph to 69.1 and EB 69.2: "this rule 69.1 1 referred to in point 5.1 requirement of accreditation in accordance with the standard LVS EN ISO/IEC 17020:2005" the main criteria in different types of bodies performing inspection "shall enter into force on the 1 June 2005. Until 31 May 2005 for accreditation in accordance with the standards EN 45004:1995 EN ' main criteria for different types of bodies performing inspection ". EB 69.2 Inspection bodies accredited in accordance with standards EN 45004:1995 EN ' main criteria for different types of bodies performing inspection ", is entitled to carry out the monitoring of complex technical pressure equipment up to the specified in the certificate of accreditation expires." 19. paragraph 17 of the annex to be expressed in the following: "17. Specify Passport related documents (for example, pressure equipment complex functional scheme of complex pressure equipment the electrical diagram, principle of complex pressure equipment deployment diagram specific installation site, developed a certain scale and indicating the distance to the other structures — structures, equipment, containment, pressure equipment exploded view drawings of the complex, which contains a complex and complex element within the specifications, pressure equipment the conformity declaration of the package and a copy of the certificate of conformity).
20. Make nosa of chapter XIII of annex a the following: KUMU "XIII. Details of the checks carried out and the regulation of the safety devices (completed inspection authority)".
Prime Minister a. Halloween economic Minister A.r. Kariņš
Search Translated Laws of Latvia