371/2002 Sb.
DECREE
The Ministry of industry and trade
of 26 March. July 2002,
laying down the procedure for the degradation and destruction of weapons, ammunition and
the manufacture of their cuts
632/2004: Sb.
The Ministry of industry and trade shall be determined according to § 79 paragraph 2. 4 to perform
§ 39 para. 2 (a). a) and b) and § 39 para. 3 (b). and Act No. 119/2002)
Coll. on the firearms and Ammunition Act and amending Act No. 156/2000 Coll.
about the validation of firearms, ammunition, and pyrotechnical items and on the
Amendment of the Act No. 288/1995 Coll. on firearms and ammunition (law on
firearms), as amended by Act No. 13/1998 Coll. and Act No.
368/1992 Coll., on administrative fees, as amended, and
Act No. 455/1991 Coll., on trades (Trade Act),
as amended, (law on weapons):
§ 1
Procedure for the undermining of the weapons
(1) when the weapon degradation
a) must ensure that the parts of the weapons and mechanisms allowing for shooting
It could not be separated and not to allow their movement;
on collapsible weapon of a gun shall be permitted the opportunity to separate these
mainly,
(b)) are carried out mainly in the breech Chamber blanking of by inserting a steel
PIN length and diameter of the Chamber; steel pin is
tightly associated with the main weld; the Guide part of the bore hole especially must be
fitted with at least three holes with the diameter of the bore hole drilled and mainly perpendicular
to the axis of the barrel, passing through only one of its walls; When the diameter of the
the bore hole over 11 mm drilled holes of ø 11 mm and
(c) the firing pin and the firing pin) is removed or the firing pin fixed zápalníkem,
reduced by at least the firing pin.
(2) the undermining of the weapons must be further
and finally, for weapons bearing) ubroušeno forehead conclusion at an angle of 45 St., and
If this is not possible, zápalníkový hole blinded by weld,
(b)) in the wall between the nábojovými revolver Chambers of turret war
odfrézovány, at least until the middle of its length, and
(c)) for weapons fitted with tank tray secured permanently against the removal of the
from restored guns or zásobníková shaft is permanently adjusted against
Insert the tray.
(3) the main part of the weapon Degradation and forbidden for weapons
performs the cut (§ 3) or destruction (section 8).
§ 2
Procedure for the undermining of the ammunition
(1) the undermining of the ammunition
and must be in a shell casing) a hole with a diameter of at least 2.5 mm allowing for
emptying the dust filling and add fluid through the hole
flegmatizaci matches, or causing
(b)) of ammunition, bullet from the cartridge case cut the dust filling,
carry out a firing cartridge case matches, can fill the inert matter.
(2) ammunition containing matches screws, lighters, fuel,
pyrotechnics or explosives (hereinafter referred to as "explosive substances")
they degrade delaborací and deactivation.
§ 3
How to cut weapons production
(1) the production of cutting weapons or the main part of the weapon is done so that the
all weapons
and vložná) barrel, the barrel or Chamber must be vložná
odfrézovány so that the steel cartridge case and projectile 2/3 reveals, Furthermore,
at gunpoint, and the fee mainly Guide part odfrézuje the bore hole 15 mm in length,
the width of the slot is equal to odfrézované diameter bore hole zvětšenému
of at least 3 mm,
(b)) the tip of the firing pin must be reduced by at least 4 mm, if this is not
feasible, remove the firing pin and hole zápalníkový blinded by welding,
(c) weapons or bed frame) weapons must be odfrézováno at least three
places so that the tension was visible, trigger, drums and return
the mechanism,
(d)) when you try to not leave the barrel of a missile shot and
(e)) can be mutually to move major parts and mechanisms of weapons and
to disassemble them.
(2) for weapons with the conclusion must also be
and finally odfrézován in length) and width equal rest mainly and
(b)) case the conclusion of equal odfrézováno rest mainly enlarged
at least 15 mm and a width equal to rest especially magnified by 10 mm.
(3) the weapons with the rest of the stack must be done on the
the back and side of the tray.
(4) in the case of the revolver must be further
and half of the firing Chambers of turret) the war blinded by inserting the
a steel pin on the length and diameter of the Chamber firmly associated with the
weld and the other half cylinder firing Chambers of odfrézována so that
rest of the treated 2/3 each reveals the Chamber to
the mouth of the war, with the Groove width is equal to the diameter of the Chamber
plus 2 mm. in the case of an odd number of cartridge Chambers with zaslepují 3
the Chamber of the cylinder, the other turret Chamber with odfrézují
in the same way and
b) barrel revolver, odfrézována on the right side so that the odfrézovaná
Groove has a width equal to the diameter of the bore hole increased by 2 mm, a length of at least
50 mm, and its beginning is positioned 10 mm from the rear of the barrel.
(5) for a disabled add-on weapons odfrézuje of at least 50% of its volume
cut in the direction of the longitudinal axis of the functional part of the add-in.
(6) in the production of cut a separate main section of the weapons follows mutatis mutandis the
in accordance with paragraphs 1 to 4.
§ 4
How to cut production of ammunition
(1) before the actual cut of ammunition shall be carried out in accordance with § 2 and depreciation
Removes the explosive substances delaborací, where ammunition is contains.
(2) for the production of cut ammunition
and odfrézuje) 50% of the volume of the entire length of the cartridge case on the side of the
the drilled hole, or at least to make them odfrézovány 2/3 her
length in place of dna and the mouth of the cartridge case; Similarly for the slice shots,
(b) in respect of other parts of ammunition), such as matches, matches
screws, lighters, with a cut of at least 2/3 performs their length or
be retained in its original form, if their dimensions or design
do not allow the cut.
§ 5
If it cannot be used in weapons, the main part of the degradation of the weapon,
a disabled add-on weapons, ammunition or the manufacture of their cuts, how to
referred to in § 1, 2, 3 or 4, he shall submit the application for the approval of the procedure for the
degradation of the weapon, the main part of the weapons, a disabled add-on weapons
ammunition or the manufacture of their cuts to the Czech Office for the testing of weapons and
ammunition (hereinafter referred to as "the authority"), which shall be accompanied by
the proposal procedure) that contains a list of operations, used equipment, installation
and release products and material
b) drawing documentation and
c) weapon, the main part of the weapons, a disabled add-on weapons or pattern
ammunition in the State against deterioration; If the size or weight
do not allow their submission, communicated to the available space to store them.
§ 6
The conditions for the allocation of the control znehodnocovací brand
(1) the holder of a firearm licence for destruction or degradation of weapons or
ammunition shall submit an application on the allocation of the control znehodnocovací the brand with
registration number at the Office. The request shall present arms licence or
a certified copy of it.
(2) the holder of a firearm licence for znehodnocenou weapon, the main part of weapons
and the weapons or their disabled add-on cuts inspection sets off
znehodnocovací tag in a visible and permanent manner, at least to the
one of the main parts of the weapon or weapons on the disabled add-in.
(3) the Deactivated ammunition or ammunition with the cut indicates visibly and
permanently on a shell casing and a shot from a .22 caliber 12.7 mm; for other types of ammunition
on their body.
(4) the location of the control znehodnocovací brand on the weapon or ammunition
It is stated in the certificate (§ 7). Pattern control tag is znehodnocovací
listed in annex 1.
§ 7
Specimen certificate
The pattern confirmation of deterioration or destruction of the weapons, the main part of the weapon,
a disabled add-on weapons, ammunition or produce their slices is given
in annex No. 2.
§ 8
The destruction of the weapons, the main part of the weapons, a disabled add-on weapons and
ammunition
(1) after receiving the weapons, the main part of a weapon or a disabled add-on
weapons shall be part of the movement to allow removal of the main parts
guns and weld the main parts of the weapons to each other. The ammunition shall be carried out
the deactivation.
(2) according to the type of weapon, the main part of a weapon or a disabled add-on
the weapon is selected at least one of the following methods of destruction,
and non-welded parts at right angles to) the axis of the barrel sections apart
a maximum of 50 mm,
(b)), with the deformation of the width, height or length must be reduced by at least
about 30%,
(c)) by breaking a severe steel demolition balls to the weapon, the main part of the
weapons or prohibited weapons were warped, so add-in that will burst
at least three places,
(d) the vehicle by swiping the severe belt) with a weight of over 40 t, taking
the height of the weapons, the main part of a weapon or a disabled add-on weapons must
reduce by at least 50% or
e) explosion using dynamite, which is placed so as to cover all
the main part of the weapon, the main part of the weapons or prohibited weapons and add-in
that the explosion originated at least three bullet fragments.
(3) after the completion of the procedures referred to in paragraph 2, the destruction is then
the procedure uses the destruction by melting in the melting furnace for metal processing
or other waste.
(4) according to the type of ammunition is selected at least one of these procedures,
and it
and delaborací followed by melting),
(b)), or
c) by burning.
Transitional and final provisions
§ 9
(1) the control znehodnocovací symbol according to the existing legislation
may only be used until the registration number allocation and control
znehodnocovací marks by the Office, but no longer than 12 months from the effective date
the effectiveness of this Ordinance.
(2) depreciation of the weapons in accordance with the existing legislation is considered to be
for the deterioration in accordance with this Ordinance, provided that such weapons are
bearing znehodnocovací brand. The same is true for manufactured
slices of weapons.
§ 10
Repeals the Decree 216/1996 Coll. on the method and the technological procedure
When the undermining of the arms and the production cuts of weapons.
§ 11
The effectiveness of the
This Decree shall enter into force on 1 January 2000. January 1, 2003.
Minister:
Ing. Samantha r in r.
Č. 1
Pattern control znehodnocovací brand
In the control tag is znehodnocovací under the letter D in the large ring
indicate the registration number of the last two digits of the year of the curved his
allocation of arms licence holders.
Č. 2
Specimen certificate of destruction of the weapon, the main part of the weapon,
a disabled add-on weapons, ammunition and their cuts has been manufactured
1. the model RS:
+---------------------------------------------------------------+
| Confirmation no........... |
| depreciation-destruction-cutting has been manufactured-weapons-ammunition |
| the main part of the weapons-a disabled add-on weapons *) |
+---------------------------------------------------------------+
| |
| Type of weapon, ammunition |
| |
| |
| Brand manufacturer |
| |
| Model (model) |
| |
| Ráže |
| |
| The serial number of the weapon |
| |
| * Delete where inapplicable) |
+---------------------------------------------------------------+
2. the reverse side of the confirmation will contain the
and) identification of licensee
1. name and surname, date of birth, place of residence, the place for entrepreneurs
business and identification number, if assigned, is a natural
person,
2. the name or business name, registered office and identification number, if
a legal person.
(b)) reference number of the authorization for destruction of the weapon, the main
part of the weapons, a disabled add-on weapons, munitions and manufacture their
slices,
(c) the location of the control znehodnocovací brand) on the weapon or ammunition, and
d) date, stamp and signature.
3. The dimensions of the commit-ID-2 according to EN ISO/IEC 7501 of 1995.
4. confirmation of the sealed into clear transparent termofólie.