Clean Energy Amendment Regulation 2012 (No. 4)

Link to law: https://www.comlaw.gov.au/Details/F2012L01403

Clean Energy Amendment Regulation 2012 (No. 4)1
Select Legislative Instrument 2012 No. 126
I, QUENTIN BRYCE, Governor-General of the Commonwealth of Australia, acting with the advice of the Federal Executive Council, make the following regulation under the Clean Energy Act 2011.
Dated 28 June 2012
QUENTIN BRYCE
Governor-General
By Her Excellency’s Command
GREG COMBET
Minister for Climate Change and Energy Efficiency
1              Name of regulation
                This regulation is the Clean Energy Amendment Regulation 2012 (No. 4).
2              Commencement
                This regulation commences on 1 July 2012.
3              Amendment of Clean Energy Regulations 2011
                Schedule 1 amends the Clean Energy Regulations 2011.
Schedule 1        Amendments
(section 3)
 
[1]           Regulation 1.3, definition of liquid petroleum gas, or LPG
substitute
liquefied petroleum gas, or LPG, has the same meaning as liquefied petroleum gas in regulation 1.03 of the NGER Regulations.
[2]           Paragraph 1.9 (1) (a)
omit
at which:
insert
in relation to which:
[3]           After subregulation 1.9 (1)
insert
      (1A)   However, if the natural gas exits from a point on a pipeline in the circumstances in paragraph (1) (a), or is combusted in the circumstances in paragraph (1) (b), during the period between 1 July 2012 and 31 August 2012, a withdrawal of natural gas is taken to have occurred on 1 September 2012.
[4]           After regulation 3.2
insert
3.3           Adjustment of provisional emissions number—Joint Petroleum Development Area and Greater Sunrise unit area
                For the definition of prescribed percentage in subsections 26 (2), 27 (2) and 28 (2) of the Act, 0% is specified in relation to the facility for the eligible financial years commencing on 1 July 2012, 1 July 2013 and 1 July 2014.
[5]           Regulation 3.5
omit each mention of
liquid petroleum gas
insert
liquefied petroleum gas
[6]           Schedule 1, Part 3, after Division 43
insert
Division 44     Manufacture of reconstituted wood‑based panels
344   (1)   The manufacture of reconstituted wood‑based panels is the physical and chemical transformation of wood, including wood particles and residues (such as chips, shavings and sawdust) into a reconstituted wood-based panel that:
                (a)    has a density of greater than 500 kg a cubic metre; and
               (b)    has individual wood particles or fibres with an average maximum dimension of no more than 30 mm.
Examples of reconstituted wood-based panels are  particleboard and medium density fibreboard.
         (2)   The manufacture of reconstituted wood‑based panels is specified as an emissions-intensive trade-exposed activity.
         (3)   The manufacture of reconstituted wood‑based panels is a moderately emissions‑intensive activity.
         (4)   The basis for the issue of free carbon units for the manufacture of reconstituted wood‑based panels is by a tonne of raw reconstituted wood-based panel that:
                (a)    has a density of greater than 500 kg a cubic metre; and
               (b)    has individual wood particles or fibres with an average maximum dimension of no more than 30 mm; and
                (c)    is produced by carrying on the emissions-intensive trade-exposed activity; and
               (d)    is of saleable quality.
Note   Saleable quality is explained in Part 2.
[7]           Schedule 1, subclause 401 (1), table, after item 2.11
insert
2.12
Manufacture of reconstituted wood‑based panels
Raw reconstituted wood-based panel of saleable quality
0.0888
0.372
n/a
Note
1.       All legislative instruments and compilations are registered on the Federal Register of Legislative Instruments kept under the Legislative Instruments Act 2003. See www.comlaw.gov.au.
 
Read Entire Law on www.comlaw.gov.au