Pursuant to the provisions of article 24 para. (4) of the law on electronic communications No. 241-XVI of November 15, 2007 (Official Gazette of the Republic of Moldova, 2008, no. 51-52, art. 155), with subsequent amendments and additions, the section 8 subpct. 1) of the regulation on the organisation and functioning of the Ministry of information and Communication Technology, approved by Government decision No. 389 of 17 May 2010 (Official Gazette of the Republic of Moldova, 2010, no. 78-80, art. 460) and its subsequent amendments, and on the basis of the recommendation ERC 70-03, approved by the European Conference of postal and Telecommunications Administrations (CEPT) with the amendments and additions to ORDON subsequent: 1. The common technical regulation ' technical parameters of short-range devices in action ", approved by order of the Minister of information technology and communications No. 16 of 21 February 2014, is modified and completed as follows: 1) in chapter II, point 4 is added to the definition of effective radiated power:-the product of the power emitted in the antenna and the antenna gain coefficient in relation to a λ/2 dipole in a direction;
2) chapter II point 5 Add new abbreviations in alphabetical order: APC
-Adaptive Control of power (Adaptive Power Control)
CEPT
BFWA
DAA
DFS
-The European Conference of postal and Telecommunications Administrations
-Wireless broadband to fixed (Broadband Fixed Wireless Access)
-Detects and avoids (Detect and Avoid)
-Dynamic frequency Selection (Dynamic Frequency Selection)
ECC
e.i.r.p.
ER-GSM
FWS
-CEPT electronic communications Committee of
-Effective isotropic radiated Power
-Extended spectrum GSM Railway (Extended spectrum for GSM for Railways)
-Fixed Wireless System (Fixed Wireless Systems)
LAES
-Application for localization Service Rescuers (Location-Application for Emergency Services)
LT2
-Location type 2 (Location Tracking Type 2)
MBANS
-Local area networks (Medical Body Area Network Systems)
SRR
-Short range Radar in vehicles (Short Range Radars)
TTT
-Traffic control Systems and road safety (Transport & Traffic Telematics)
WIA
-Industrial applications Wireless (Wireless Industrial Applications)
3) At chapter IV subpct 9.1 the table in item 2 is amended and shall read as follows: 2. TECHNICAL CONDITIONS:
Frequency band
The power/
Magnetic field
Functional cycle
The spread between
channels
Notes
the
6765-6795 kHz
dBμA 42/m
to 10 m
Without restrictions
Without gap
The same frequency band is
identified in specification of IR-009
(b)
13.553-13.567 MHz
dBμA 42/m
to 10 m
Without restrictions
Without gap
The same frequency band is identified in specification of IR-009
(c)
26.957-27.283 MHz
dBμA 42/m
10 m 10 mW
Without restrictions
Without gap
The same frequency band is identified in specification of IR-009
C1
26.995; 27.045; 27.095; 27.145; 27.195 MHz
100 mW e.r.p.
≤ 0.1%
≤ 10 kHz
The same frequency band is identified in specification of IR-008
(d)
40.660-40.700 MHz
10 mW e.r.p.
Without restrictions
Without gap
(e)
138.20-138.45 MHz
10 mW e.r.p.
≤ 1%
Without gap
E1
169.400-169.475 MHz
500 mW er p
≤ 1%
≤ 50 kHz
The same frequency band is identified in the specifications of IR and IR-002-010
E2
169.4000-169.4875 MHz
10 mW er p
≤ 1%
Without gap
Equipment focus or contain individual equipment are excluded
E3
169.4875-169.5875 MHz
10 mW er p
≤ 0.001 percent, except 0000-0600 local time,
When ≤ 0.1%
Without gap
Equipment focus or contain individual equipment are excluded.
The same frequency band is
identified in specification of IR-010
E4
169.5875-169.8125 MHz
10 mW er p
≤ 0.1%
Equipment focus or contain individual equipment are excluded
(f)
433.05-434.79 MHz
10 mW e.r.p.
≤ 10%
Without gap
F1
433.05-434.79 MHz
1 mW e.r.p.-13 dBm/10 kHz
≤ 100%
Without gap
Power density is
limited to-13 dBm/10 kHz
for broadband modulation with bandwidth greater than 250 kHz
F2
434.04-434.79 MHz
10 mW e.r.p.
≤ 100%
≤ 25 kHz
G1
863-870 MHz
(Note 3.3 3.4 and 3.6;)
25 mW er p
≤ 0.1% or LBT
(Note 3.1 and 3.5)
≤ 100 kHz for 47 or more channels (Note 3.2)
FHSS Modulation
25 mW er p
(Note 3.11)
the density of
power-4.5 dBm/100 kHz
≤ 0.1% or LBT
(Note 3.1;
3.5 and 3.6)
Without gap
DSSS Modulation.
Other broadband modulation besides FHSS
25 mW er p
≤ 0.1% or LBT
(Note 3.1 and 3.5)
≤ 100 kHz for 1 or more channels (Note 3.2 and 3.7)
Narrowband modulation/wide
g 1.1
868.00-868.60 MHz
(Note 2.1)
25 mW e.r.p.
≤ 1% or LBT
(Note 3.1)
Without a gap, for 1 or more channels (Note 3.2)
Narrowband modulation/wide
g 1.2
868.70-869.20 MHz
(Note 2.1)
25 mW e.r.p.
≤ 0.1% or LBT (Note 3.1)
Without a gap, for 1 or more channels (Note 3.2)
Narrowband modulation/wide
1.3 g
869.40-869.65 MHz
(Note 2.1)
500 mW e.r.p.
≤ 10% or LBT
(Note 3.1)
25 kHz for 1 or more channels
Narrowband modulation/wide
g 1.4
869.70-870.00 MHz
5 mW e.r.p.
Without restrictions
Without a gap, for 1 or more channels
Narrowband modulation/wide
25 mW e.r.p.
≤ 1% or LBT
G2
870-876 MHz
25 mW e.r.p.
≤ 0.1%
For protecting
ER-GSM (873-876 MHz), the working cycle is ≤ 0.01%
≤ 200 kHz
The same frequency band is
identified in the specification
IR-IR-002 and 005
g 2.1
870.000-875.800 MHz
25 mW e.r.p.
≤ 0.1%
For protecting
ER-GSM (873-876 MHz)
the working cycle
is ≤ 0.01%
≤ 600 kHz
The same frequency band is
identified in the specification
IR-IR-002 and 005
G3
915-921 MHz
25 mW e.r.p.
≤ 0.1%
To protect ER-GSM (918-921 MHz), the working cycle is ≤ 0.01%
≤ 200 kHz
The same frequency band is
identified in the specification
IR and IR-010-011
g 3.1
915.200-920.800 MHz
25 mW e.r.p.
with the exception of the 4 channels mentioned in (Note 3.17)
where applies
100 mW
≤ 1%
To protect ER-GSM (918-920,8 MHz), the working cycle
is ≤ 0.01%
≤ 600 kHz
with the exception of the 4 channels mentioned in (Note 3.17), which applies to ≤ 400 kHz
The same frequency band is
identified in the specification
IR and IR-010-011
h
2400-2483.5 MHz
10 mW e.i.r.p.
Without restrictions
Without gap
The same frequency band is
identified in the specification
IR-IR-003 and 006
I
5725-5875 MHz
25 mW e.i.r.p.
Without restrictions
Without gap
(j)
24.00-24.25 GHz
100 mW e.i.r.p.
Without restrictions
Without gap
The same frequency band is
identified in the specification
IR-005
k
61.0-61.5 GHz
100 mW e.i.r.p.
Without restrictions
Without gap
K1
57-64 GHz
100 mW e.i.r.p.
Without restrictions
Without gap
l
122-122.25 GHz
10 dBm e.i.r. p/
250 MHz and
-48 dBm/MHz
30 ° elevation
Without restrictions
Without gap
L1
122.25-123.0 GHz
100 mW e.i.r.p.
Without restrictions
m
244-246 GHz
100 mW e.i.r.p.
Without restrictions
Without gap
n
3.1-4.8 GHz
6 to 9 GHz
*
*
*
Ultra wide band generic
* Detailed requirements in Decision ECC/DEC/(06) 4
N1
6.0-8.5 GHz
*
*
*
Ultra wide band aboard
aircraft.
* Detailed requirements in Decision ECC/DEC/(12) 3
4) At chapter IV subpct 9.1 in the table in paragraph 3 shall be inserted: (a) changes) in the phrase, subpct, 3.8 2g1-g2-g3-g4 "shall be replaced with the phrase, 2g1-2 g 2-2g3-2 g 4";
b) in subpct. 2 c, 3.10, phrase, 2d, 2f-f1-f2, 2 h and 4i "shall be replaced with the phrase, 2 c, 2d, 2f-2 h-2f1 2f2, and 4i";
с. subpct) in phrase, 3.11-f1-f2 2f "shall be replaced with the phrase, 2f-2f1-2f2";
subpct. d) 3.14 phrase, 2g1-g2-g3 "shall be replaced with the phrase, 2g1-2 g 2-2g3".
5) At chapter IV subpct 9.1 in the table in paragraph 3 Add subpct., 3.17 Center Frequencies are channel 916.3 MHz, 917.5 MHz, 918.7 MHz and 919.9 MHz channel bandwidth is 400 kHz ".
6) At chapter IV is the name of the subpct. 9.2 exposes new, IR-002-MDA-Devices with small radius of action intended for the detection and gathering of data. "
7) At chapter IV subpct. 9.2 pts 1 Add new fields of application, technical specification IR-002 contains the frequency bands and rules and informative parameters recommended for a specific number of devices, which includes:
-Detection of emergency victims and valuables such as detecting victims of avalanches;
-Reading of the indications for measuring apparatus;
-Sensors (water, gas and electricity; instruments measuring pollution, meteorological data from the environment, such as levels of food allergens (pollen, dust), electromagnetic pollution (solar activity) and actuators (control devices such as traffic lights road);-MBANS, used for the collection of health data, are intended to be used in medical settings and to patients. Designed as a small local networks of power, used for the transmission of non-voice data from and to medical devices, for the purposes of monitoring, diagnosis and treatment of patients;
WIA-used as industrial environments, communications including monitoring and communications service, wireless sensors and mechanisms of action. "
8) At chapter IV subpct. 9.2, the table in item 2 is amended and shall read as follows: 2. TECHNICAL CONDITIONS:
Band
frequency
Magnetic field
Functional cycle
Spread
between channels
Notes
the
456.9-457.1 kHz
7 dBμA/m to 10 m
Without restrictions
Continuous wave-no modulation
Detection of victims of avalanches. Center frequency is 457 kHz
(b)
169.4-169.475 MHz
500 mW e.r.p.
≤ 10%
≤ 50 kHz
Telemetry
(c)
-875.600 870.000 MHz
500 mW e.r.p.
≤ 2.5% and APC
(Note 3.1).
For the protection of ER-GSM
(873-875,6 MHz), the working cycle is ≤ 0.01%
(Note 3.2)
≤ 200 kHz
Individual license may be required for Metropolitan/rural networks.
PCA is required to be able to reduce the power of the
the maximum amount up to ≤ 5 mW.
The same frequency band is
identified in the specifications of IR and IR-001-005
D1
2500-2483.5 MHz
1 mW e.i.r.p.
Appropriate mechanisms for sharing of the spectrum (d/ex. LBT and AFA) should be implemented by equipment and ≤ 10%
≤ 3 MHz
The same frequency band is
identified in specification of IR-012.
Applies only inside
medical institutions
D2
2500-2483.5 MHz
10 mW e.i.r.p.
Appropriate mechanisms for sharing of the spectrum (d/ex. LBT and AFA) should be implemented by equipment and ≤ 2%
≤ 3 MHz
The same frequency band is
identified in specification of IR-012.
Applies only inside
the patient's residence
(e)
5725-5875 MHz
≤ 400 mW e.i.r.p.
The APC is required.
Appropriate mechanisms for sharing of the spectrum must be implemented.
(Note 2.1)
≥ 1 MHz
and ≤ 20 MHz
For WIA.
APC is needed to reduce the e.i.r.p. until ≤ 25 mW.
The same frequency band is
identified in specification of IR-001
9) At chapter IV subpct. 9.2 in the table in point 3 is added: subpct 3.1, 3.2 and 3.3, 3.1 A working cycle of up to 10% may be allowed for network points that are part of Metropolitan/rural networks, such as utilities or other data collection applications. ", 3.2 except when the rail operator is employed to avoid interference in the ER-GSM occupied."
3.3 it is necessary, implementation of DFS in the band 5725-5850 MHz frequencies to ensure adequate protection for radar service (including cameras), implementation is required YES the band 5725-5875 MHz frequencies for protection, and BFWA frequency band-5815 5795 MHz for TTT applications protection. "
10) At chapter IV subpct from table 9.3 (2) is amended and shall read as follows: 2. TECHNICAL CONDITIONS:
Frequency band
Power
Functional cycle
The spread between channels
Notes
the
2400-2483.5 MHz
100 mW
e.i.r.p.
Appropriate mechanisms for
spectrum sharing
(d/ex LBT, DAA) must be implemented by
equipment
Without gap
For different modulation of FHSS
maximum e.i.r.p. density shall be limited to 10 mW/MHz
(b)
57-66 GHz
40 dBm
e.i.r. p medium
Appropriate mechanisms for
spectrum sharing
(d/ex LBT, DAA) must be implemented by
equipment
Without gap
Fixed installations are not allowed.
The maximum average e.i.r.p. density shall be
limited to 13 dBm/MHz.
Links from point-to-point fixed Service are governed by the ECC/REC/(05) 02 and ECC/REC/(09) 01
11) At chapter IV para. 9.5 table in section 2 is amended and shall read as follows: 2. TECHNICAL CONDITIONS:
Frequency band
Power
Functional cycle
Spread
between channels
Notes
the
870.00-875.80
MHz
500 mW e.r.p.
100 mW e.r.p.
≤ 0.1%
To protect ER-GSM (873.0-875.8 MHz), the working cycle is limited to
≤ 0.01%
≤ 500 kHz
500 mW limit is for vehicle-vehicle applications.
The limit is 100 mW for in-vehicle applications. The APC is required.
APC reduce the power of the maximum amount up to ≤ 5 mW.
The same frequency band is
identified in the specifications of IR-001
and IR-002
B1
5795-5805 MHz
2 W e.i.r.p.
8 W e.i.r.p.
Without restrictions
Approval for systems with higher power of 8 W
B2
5805-5815 MHz
2 W e.i.r.p.
8 W e.i.r.p.
Without restrictions
(c)
76-77 GHz
maximum 55 dBm e.i.r.p.
Without restrictions
Without gap
Average power of 50 dBm or 23.5 dBm for radars
D1
21.65-26.65 GHz
*
*
*
For The SRR.
* Detailed requirements view Decision ECC/DEC/(04) 10.
New equipment is not placed SRR on the market as of 1 July 2013
D2
24.25-26.65 GHz
*
*
*
For The SRR.
* Detailed requirements view Decision ECC/DEC/(04) 10.
SRR equipment may be placed on the market only until 1 January 2018
(e)
77-81 GHz
*
*
*
For The SRR.
* Detailed requirements view Decision ECC/DEC/(04) 3
F1
-24.050 24.075 GHz
100 mW e.i.r. p
Without restrictions
For SRR
F2
24.150 24.075-GHz
e.i.r. p 0.1 mW
Without restrictions
For SRR
100 mW e.i.r. p
≤ 4μs/40 kHz stopping every 3 ms
For SRR
≤ 1μs/40 kHz stop every 40 ms
F3
24.150-24.250 GHz
100 mW e.i.r. p
Without restrictions
For SRR
G1
24.250-24.495 GHz
-11 dBm e.i.r. p
≤ 0,25%/s/25 MHz
For SRR
G2
24.495-24.500 GHz
-8 dBm e.i.r. p
≤ 1,5%/s/5 MHz
G3
24.250-24.500 GHz
20 dBm e.i.r. p
≤ 5%/s/25 MHz
16 dBm e.i.r. p
≤ 2.3%/s/25 MHz
12) At chapter IV designation subpct. expose 9.6 new: IR-006-MDA-Devices with small radius of action intended for radiodeterminare applications ".
13) At chapter IV subpct. table 9.6 from item 2 is amended and shall read as follows: 2. TECHNICAL CONDITIONS:
Frequency band
Power
Cycle
usage
The spread between channels
Notes
the
2400-2483.5 MHz
25 mW e.i.r.p.
Without restrictions
Without gap
(b)
9200-9500 MHz
25 mW e.i.r.p.
Without restrictions
Without gap
(c)
9975-9500 MHz
25 mW e.i.r.p.
Without restrictions
Without gap
(d)
10.5-10.6 GHz
25 mW e.i.r.p.
Without restrictions
Without gap
(e)
13.4-14.0 GHz
25 mW e.i.r.p.
Without restrictions
Without gap
(f)
24.05-24.25 GHz
100 mW e.i.r.p.
Without restrictions
Without gap
Frequency band-24.0 GHz 24.25 is identified with the same parameters as in transceiver specification IR-001, j
g
4.5-7.0 GHz
-41/MHz, 3dBm e.i.r. p outside the tank
Without gap
For TLPR
h
8.5-10.6 GHz
-41/MHz, 3dBm e.i.r. p outside the tank
Without gap
For TLPR
I
27.0 24.05-GHz
-41/MHz, 3dBm e.i.r. p outside the tank
Without gap
For TLPR
(j)
57-64 GHz
-41/MHz, 3dBm e.i.r. p outside the tank
Without gap
For TLPR
k
75-85 GHz
-41/MHz, 3dBm e.i.r. p outside the tank
Without gap
For TLPR
l
6-8.5 GHz
(Note 3.1)
Without gap
For LPR industrial
m
24.05-26.5 GHz
(Note 3.1)
Without gap
n
57-64 GHz
(Note 3.1)
Without gap
a
75-85 GHz
(Note 3.1)
Without gap
p
17.1-17.3 GHz
26 dBm e.i.r. p
Without gap
For GP SAR
q
30 MHz-12.4 GHz
(Note 3.2)
For GPR/WPR
r
8.0-2.2 GHz
(Note 2.1)
Device materials detection
s1
3.1-4.8 GHz
*
*
*
* Detailed requirements view
Recommendation ECC/REC/09 (11)
s2
3.1-4.8 GHz
*
*
*
* Detailed requirements view
Recommendation ECC/REC/10 (11)
14) At chapter IV designation subpct. 7″ expose new, IR-007-MDA-Devices with small radius of action intended for alarm systems (including social alarms) "15) At chapter IV subpct. 6.0 the table in item 2 is amended and shall read as follows: 2. TECHNICAL CONDITIONS:
Frequency band
Power
Functional cycle
The spread between channels
Notes
the
868.6-868.7 MHz
10 mW e.r.p.
≤ 1%
25 kHz
(b)
869.25-869.30 MHz
10 mW e.r.p.
≤ 0.1%
25 kHz
(c)
869.65-869.70 MHz
25 mW e.r.p.
≤ 10%
25 kHz
(d)
869.20-869.25 MHz
10 mW e.r.p.
≤ 0.1%
25 kHz
Social alarms
(e)
869.30-869.40 MHz
10 mW e.r.p.
≤ 1%
25 kHz
16) At chapter IV subpct. table 6.1, point 2 is hereby amended and shall read as follows: 2. TECHNICAL CONDITIONS:
Frequency band
Power
The cycle of usage
The spread between channels
Notes
the
26.995; 27.045; 27.095; 27.145; 27.195 MHz
100 mW e.r.p.
Without restrictions
10 kHz
(b)
34.995-35.225 MHz
100 mW e.r.p.
Without restrictions
10 kHz
Only for flight models
(c)
40.665; 40.675; 40.685; 40.695 MHz
100 mW e.r.p.
Without restrictions
10 kHz
17) At chapter IV subpct. 6.2 the table in item 2 is amended and shall read as follows: 2. TECHNICAL CONDITIONS:
Frequency band
Magnetic field
The cycle of usage
The spread between channels
Notes
A1
9-90 kHz
72 dBμA/m to 10 m
Without restrictions
Without gap
In the case of external antennas may only be used for loop type coil antennas
A2
90-119 kHz
42 dBμA/m to 10 m
Without restrictions
Without gap
In the case of external antennas may only be used for loop type coil antennas
A3
119-135 kHz
66 dBμA/m to 10 m
Without restrictions
Without gap
In the case of external antennas may only be used for loop type coil antennas
(b)
135-140 kHz
42 dBμA/m to 10 m
Without restrictions
Without gap
In the case of external antennas may only be used for loop type coil antennas
(c)
140-148.5 kHz
37.7 dBμA/m to 10 m
Without restrictions
Without gap
In the case of external antennas may only be used for loop type coil antennas
(d)
6765-6795 kHz
42 dBμA/m to 10 m
Without restrictions
Without gap
(e)
7400-8800 kHz
9 dBμA/m to 10 m
Without restrictions
Without gap
(f)
13.553-13.567 MHz
42 dBμA/m to 10 m
Without restrictions
Without gap
F1
13.410-13.553 MHz
13.567-13.710 MHz
9 dB µA/m to 10 m
Without restrictions
Without gap
Only for RFID, but in common with the f
13.110-13.410 MHz
13.710-14.010 MHz
-3.5 dB µA/m to 10 m
Without restrictions
Without gap
Only for RFID, but in common with bandaf
12.660-13.110 MHz
14.010-14.460 MHz
-10 dB µA/m to 10 m
Without restrictions
Without gap
Only for RFID, but in common with bandaf
11.810-12.660 MHz
14.460-15.310 MHz
-16 dB µA/m to 10 m
Without restrictions
Without gap
Only for RFID, but in common with the f
F2
13.553-13.567 MHz
60 dB µA/m to 10 m
Without restrictions
Without gap
Only for RFID and EAS
F3
13.460-13.553 MHz
13.567-13.660 MHz
27 dB µA/m to 10 m
Without restrictions
Without gap
Only for RFID, but in common with f2
13.360-13.460 MHz
13.660-13.760 MHz
Linear 27 crossing until-3.5 dB µA/m to 10 m
Without restrictions
Without gap
Only for RFID, but in common with f2
13.110-13.360 MHz
13.760-14.010 MHz
-3.5 dB µA/m to 10 m
Without restrictions
Without gap
Only for RFID, but in common with f2
12.660-13.110 MHz
14.010-14.460 MHz
-5 dB µA/m to 10 m
Without restrictions
Without gap
Only for RFID, but in common with f2
g
26.957-27.283 MHz
42 dBμA/m to 10 m
Without restrictions
Without gap
h
10.2 11.0-MHz
9 dBμA/m to 10 m
Without restrictions
Without gap
k
3155-3400 kHz
dBμA/13.5 m to 10 m
Without restrictions
Without gap
In the case of external antennas may only be used for loop type coil antennas
L1
148.5 kHz-5 MHz
-15 dBμA/m to 10 m
Without restrictions
Without gap
In the case of external antennas may be used only by loop type coil antennas.
The maximum permissible level of meter
electromagnetic-5 dB µA/m to 10 m for systems that operate with bandwidths greater than 10 kHz
L2
5-30 MHz
-20 dBμA/m to 10 m
In the case of external antennas may be used only by loop type coil antennas.
The maximum permissible level of meter
electromagnetic-5 dB µA/m to 10 m for systems that operate with bandwidths greater than 10 kHz
L3
400-600 kHz
-8 dBμA/m to 10 m
Only for RFID.
In the case of external antennas may be used only by loop type coil antennas.
The maximum permissible level of meter
electromagnetic-5 dB µA/m to 10 m for systems that operate with bandwidths greater than 10 kHz.
These systems must operate with bandwidths of at least 30 kHz
18) At chapter IV subpct. 6.2 in the table in paragraph 3 shall be inserted: (a) changes in 3.1) subpct words, 2a2-a3, 2b, 2 c, 2 k and 2l1-l2 "shall be replaced with the phrase, 2a2-2a3, 2b, 2 c, 2 k and 2l1-2l2";
b) in subpct., 2l1 3.6 phrase-l2 "shall be replaced with the phrase, 2l2, 2l1-".
19) At chapter IV subpct. in the table in point 9.10 1 introduce modifications: a) phrase, the frequency bands set out in points 2d1, e1, e2, e3, e4 "shall be replaced with the phrase, the frequency bands set out in paragraphs 2d, 2e1, 2e2, 2e3, 2e4";
b) collocation, Prostheses for persons with hearing impairments: 2b, c, d, h1, h2, i "shall be replaced with the phrase, for persons with Hearing disabilities hearing: 2b, 2 c, 2d, 2h1, 2h2, 2i";
(c)) the phrase, Radiomicrofoane: 2a, c, d, e1, e2, e3, e4, f, g "shall be replaced with the phrase, Radiomicrofoane: 2a, 2 c, 2d, 2c1, 2e1, 2e2, 2e3, 2e4, 2f, 2 g, 2g1".
20) At chapter IV subpct. table 9.10 (2) is amended and shall read as follows: 2. TECHNICAL CONDITIONS:
Frequency band
Power
The cycle of usage
The spread between channels
Notes
the
47.0-29.7 MHz
10 mW e.r.p.
Without restrictions
≤ 50 kHz
Adjusting the frequency
(b)
173.965-174.015 MHz
2 mW e.r.p.
Without restrictions
≤ 50 kHz
Prosthetics for people with
IMSI
(c)
863-865 MHz
10 mW e.r.p.
Without restrictions
Without gap
C1
916.1-916.5 MHz, 917.3 MHz, 918.5-917.7-918.9 MHz 919.7-920.1 MHz
10 mW e.r.p.
≤ 25%
≤ 400 kHz
The same frequency band is identified in the specifications of IR-IR-001 and 011
(d)
174-216 MHz
50 mW e.r.p.
Without restrictions
Without gap
Adjusting the frequency. Shall be authorised
E1
786-470 MHz
50 mW e.r.p.
Without restrictions
Without gap
Adjusting the frequency. Shall be authorised
E2
786-789 MHz
12 mW e.r.p.
Without restrictions
Without gap
On the basis of adjustment. Shall be authorised
E3
823-826 MHz
20 mW e.i.r.p. 100 mW e.i.r. p
Without restrictions
200 kHz
Be approved. 100 mW for body worn microphones
E4
826-832 MHz
100MW e.i.r.p.
Without restrictions
200 kHz
Shall be authorised
(f)
1785-1795 MHz
20 mW 50 mW e.i.r.p. e.i.r. p
Without restrictions
Without gap
Be approved. 50 mW for body worn microphones
g
1795-1800 MHz
20 mW 50 mW e.i.r.p. e.i.r. p
Without restrictions
Without gap
50 mW for body worn microphones
G1
1800-1804.8 MHz
20 mW e.i.r.p. 50 mW e.i.r.p.
Without restrictions
Without gap
50 mW for equipment worn on the body
H1
169.4-169.475 MHz
10 mW er p
Without restrictions
≤ 50 kHz
500 mW er p
Without restrictions
≤ 50 kHz
Shall be authorised
H2
169.4875-169.5875 MHz
10 mW er p
Without restrictions
≤ 50 kHz
500 mW er p
Without restrictions
≤ 50 kHz
Shall be authorised
I
174.0 169.4-MHz
10 mW er p
Without restrictions
≤ 50 kHz
With frequency adjustment
(j)
1492-1518 MHz
50 mW e.i.r. p
Without restrictions
Without gap
With frequency adjustment.
Be approved. In internal
21) At chapter IV subpct. 9-table in section 2 is amended and shall read as follows:
2. TECHNICAL CONDITIONS:
Frequency band
Power
Functional cycle
The spread between channels
Notes
A1
2446-2454 MHz
≤ 500 mW e.i.r.p.
Without restrictions
Without gap
A2
2446-2454 MHz
> 500mW-4W e.i.r.p.
≤ 15% will use FHSS
Without gap
Higher power of 500 mW are prohibited within the limits of a working cycle and rooms of all transmitters in this case must be ≤ 15% in any length of 200 ms
B1
865.6-865 MHz
100 mW e.r.p.
Without restrictions
≤ 200 kHz
B2
865.6-867.6 MHz
2 W e.r.p.
Without restrictions
≤ 200 kHz
B3
867.6-868.0 MHz
500 mW e.r.p.
Without restrictions
≤ 200 kHz
(c)
915-921 MHz
4 W e.r.p. (Note 3)
To protect ER-GSM
(918-921 MHz)
DAA is required
≤ 400 kHz
The same frequency band is identified in the specifications of IR-IR-001 and 010
22) At chapter IV subpct. 9 in the table in paragraph 3 shall be added: 3.6 subpct 3.6 Emissions in c-band are permitted only with er p 4 W four channels with frequencies 916.3 MHz, Center 917.5 MHz, 918.7 MHz and 919.9 MHz; each with a maximum bandwidth of 400 kHz.
23) At chapter IV subpct. 9.12 table in section 2 is amended and shall read as follows: 2. TECHNICAL CONDITIONS:
Frequency band
Power
Cycle
functional
The spread between
channels
Notes
the
9-315 kHz
30 dB/m at 10 m
≤ 10%
Without gap
Apply for medicinal active implants for ultra low power (Ultra Low Power Active Medical Implants), which uses the techniques of loop telemetry purposes
(b)
315-600 kHz
-5 dBμA/m to 10 m
≤ 10%
Without gap
Apply for animal implantation devices
(c)
30-37.5 MHz
1 mW e.r.p.
≤ 10%
Without gap
Apply for medicinal membranes implants of ultra low power (Ultra Low Power medical implants membranes) used to measure blood pressure
(d)
12.5-20.0 MHz
-7 dBμA/m to 10 m
≤ 10%
Without gap
Apply for ULP-AID, only indoors.
The maximum level of the electromagnetic field is specified for bandwidth of 10 kHz.
Mask of ULP-AID is defined as:
-3 dB at 300 kHz bandwidth;
-10 dB at 800 kHz bandwidth;
-20 dB at 2 MHz bandwidth.
(e)
2500-2483.5 MHz
10 dBm e.i.r. p
LBT + AFA and < 10%
1 MHz
Active Implants for medicinal strength ultra low.
Some transmitters may combine adjacent channels to increase bandwidth over 1 MHz
24) At chapter IV subpct. 9.13 table in section 2 is amended and shall read as follows: 2. TECHNICAL CONDITIONS:
Band
frequency
Power
Functional cycle
Spread
between channels
Notes
the
863-865 MHz
10 mW e.r.p.
Up to 100%
Without gap
Wireless devices for streaming audio
and multimedia.
The same frequency band is identified in specification of IR-010
(b)
864.8-865 MHz
10 mW e.r.p.
Up to 100%
50 kHz
Narrowband analogue devices
(c)
1795-1800 MHz
20 mW e.r.p.
Up to 100%
Without gap
(d)
87.5-108 MHz
50 nW
e.r.p.
Up to 100%
200 kHz
25 at the end of the document) shall be added to annex II: list of ECC decisions and recommendations, which will contain the following: ECC/DEC/(06) 4
Harmonised conditions for the equipment with wide band ultra technology (UWB) in strips beneath 10.6 GHz
The harmonised conditions for devices using Ultra-wideband (UWB) technology in bands below 10.6 GHz
ECC/DEC/(12) 3
Harmonised conditions for aircraft applications UWB's
The harmonised conditions for UWB applications onboard aircraft
ECC/REC/09 (11)
Location systems-TYPE 2 positional UWB (LT2)
UWB Location Tracking Systems TYPE 2 (LT2)
ECC/REC/10 (11)
Positional location applications for emergencies and disasters
Location tracking application for emergency and disaster situations
ECC/DEC/(04) 10
Designated for temporary entry of SRR automobile
Designated for the temporary introduction of Automotive SRR
ECC/DEC/(04) 3
Automobile short range radars in the band 77-81 GHz
Automotive Short Range Radars in the band 77-81 GHz
ECC/REC/(05) 02
64-66 GHz-Fixed Service
64-66 GHz Fixed Service
ECC/REC/(09) 01
The use of belt 57-64 GHz for FWS point-to-point systems
Use of the 57-64 GHz band for point-to-point FWS
2. technical regulation and standardization Service will publish the order of the Ministry of information technology and communications concerning the modification and completion of technical regulation ' technical parameters of short-range devices "in the Official Gazette of the Republic of Moldova and will place this order on the official website of the Ministry of information and Communication Technology.
3. This order shall come into force at 9 months from the date of its publication in the Official Gazette of the Republic of Moldova.
4. control the execution of the present order is put in charge of Mr. Valois CAMPBELL, Deputy Minister of information and communication technology.
INFORMATION TECHNOLOGY and COMMUNICATIONS MINISTER Pavel FILIP No. 82. Chisinau, October 19, 2015.
