Advanced Search

Amendments To The Cabinet Of Ministers Of 13 January 2009 Regulations No. 30 "provisions For Implements And Trailers For The Technical Inspection And Technical Control Of The Roads"

Original Language Title: Grozījumi Ministru kabineta 2009.gada 13.janvāra noteikumos Nr.30 "Noteikumi par traktortehnikas un tās piekabju valsts tehnisko apskati un tehnisko kontroli uz ceļiem"

Subscribe to a Global-Regulation Premium Membership Today!

Key Benefits:

Subscribe Now for only USD$40 per month.
Cabinet of Ministers Regulations No. 767 Riga 2012 13 November (pr. Nr. 64) 29 amendments to the Cabinet of Ministers of 13 January 2009 Regulations No. 30 "provisions for implements and trailers for the technical inspection and technical controls on the road" issued under the Highway Traffic Act in article 16, the seventh paragraph to make the Cabinet of 13 January 2009 Regulations No. 30 "provisions for implements and trailers for the technical inspection and technical control of the roads" (Latvian journal, 2009 10. no; 2011, 202. No.) the following amendments: 1. Make paragraph 8 by the following: ' 8. implements and trailers in State control of technical roadworthiness and technical control on the road, check compliance with the rules referred to in annex 1. The Inspector identified deficiencies and damage depending on their significance evaluated by one of the following ratings: 8.1 detailed deficiencies or damage which directly affect traffic and safety (hereinafter 1. rating); 8.2. lack or damage affecting the environment can affect traffic safety (hereinafter referred to as 2. rating); 8.3. a dangerous shortage or damage, threatening the environment, human health, life or safety (hereinafter referred to as the 3 rating) and forbidding to participate in road traffic to key controls. " 2. To supplement the provisions under point 8.1 as follows: "If the technical and its 8.1 trailer no shortage or damage, the condition it evaluates to 0, rating." 3. Express 11.1. subparagraph as follows: "' key-mandatory 11.1 technical inspection according to the Road Traffic Act the recurrence or technical test that is performed, if repeated in the inspection deadline, or if you received the rating, or if 3 technical controls on the road trailer or its technical shortcomings or defects found, rated rated 3;". 4. Make a point 20 as follows: "20. After data comparison the existing permission to participate in road traffic is voided and the Inspector of implements windshield remove previous technical inspection sticker or revoke the technical inspection card." 5. Express 22 the following: "the technical condition of the 22 end of control inspector, subject to identified deficiencies or damage: 22.1. identifies and implements the technical condition of the trailer and equipment evaluation; 22.2. the present technical inspection shall be issued by the Protocol and it implements the driver; 22.3. take the view label (tag); 22.4. the record shall be made of the technical and the content of the driver in the system. " 6. Express 24 as follows: 24. If the implements and its technical condition and trailer equipment complies with the provisions of annex 1 of these requirements and has no flaws or defects observed that were evaluated with 2 or 3 rating, is given permission to participate in road traffic and issued the technical inspection sticker (talon). The technical inspection sticker (talon): 24.1. implements its trailer or national registration number, make, model or type; 24.2. the month, which is a valid technical inspection sticker (talon); 24.3. the name of the Inspector who made the implements or its technical condition of trailer control. " 7. Express 26 the following: 26. If the technical or the trailer found shortcomings and damage rated: 26.1.2. assessment, temporary permission is given 30 days to participate in road traffic and issued the technical inspection sticker (talon); 26.2. the rating is 3 given permission or temporary permission to participate in road traffic and the technical inspection sticker (talon) is not issued. " 8. Supplement with 37.1 points as follows: "If the technical or 37.1 trailer found shortcomings and defects, rated at 2. assessment of the existing authorization to participate in road traffic is voided and the Inspector of implements windshield remove previous technical inspection sticker or revoke the technical inspection card and give temporary permission to participate in the 30-day road traffic." 9. Express 38 and 39 of the following paragraph: "38. If the technical or the trailer found shortcomings and defects, rated at 3. evaluation, the Inspector of implements windshield remove previous technical inspection sticker or revoke the technical inspection card. 39. in order to receive permission to participate in road traffic, implements or the trailer owner (Manager) the shortcomings noted and damage and presented the technical or the trailer inspection or ' key again. " 10. Replace the in number and 40.2 word "rated" with 2 numbers and the words "rated 2 or 3". 11. Replace paragraph 42, the number and the word "assessment" with 2 numbers and the words "rated 2 or 3". 12. Express 44 the following: "44. the Agency's decision may appeal to the Court of Justice of the administrative procedure law." 13. Express annex 1 (1) of the following: "1. Implements and the identification number of the trailer are clean, readable, and without mechanical damage. They correspond to the manufacturer the labelling requirements and regulations for the registration of trailers and implements. " 14. Replace annex 1, paragraph 3 of the numbers ' 83:2007 "by the numbers" 83:2012 ". 15. Express of annex 1, paragraph 40 and 41 the following: "40. Implements trailers have two rear triangle reflector in red and two other forms of reflectors in front of a white and orange sides. 41. retro-reflectors of trailers and implements are installed symmetrically in relation to the average trailer or implements garenplakn. Reflector surfaces are free from damage (such as cracks, corrosion, izlūzum). " 16. Put 1 point 47 of annex by the following: "47. The steering wheel play must not be greater than the manufacturer's specified. If relevant data are not available, an imaginary point displacement along the circumference of the steering wheel, between the extreme positions of play should not exceed 1/4 (one-fifth) of the diameter of the steering wheel. " 17. Make 1.82 as follows: "82. Tyres not ply layer atslāņoj atsedzoš damage to the body, the side of the tread separated or protective coating. Minimum tyre tread depth technical and its trailers is 1.0 mm. " 18. Make 1. the title of Chapter VI of the annex by the following: "VI. Frame (pusrām), engine, clutch, the car and the truck compartment". 19. Amend Annex 1, paragraph 100 of the word "increase". 20. Make 1.132. paragraph by the following: "132. Fuel supply system devices and assemblies are not damaged and are fixed according to the requirements of the manufacturer. A fuel spill is not allowed. " 21. Make the annex by the following: "2. in the annex to Cabinet of Ministers of 13 January 2009 Regulations No 30 requirements, assessment criteria No. PO box Description of the evaluation criteria 1. 2. 3. I. equipment 1.1. Implements and trailer identification numbers is not clean and readable. They do not meet the manufacturer's requirements labelling requirements and regulations for the registration of trailers and implements x 1.2. Manufacturer's plate industrial attached. Records not legible plate x 1.3. National registration number plates type does not meet the national standard EN 83:2012 "implements and trailers the national registration plate" x 1.4. National registration number plate is attached to the place designated by the manufacturer, not in the horizontal, it is mechanically, and painted or otherwise damage x 1.5. National registration number plate is not clean and legible x 1.6. Self-propelled implements is not provided with the design of the rear-view mirrors x 1.7. Damaged mirror coating. Inadequate fastening due to movement during the arbitrary change in the position of the mirror x 1.8. Rear view side mirrors are not adjustable x 1.9. Implements is not fitted with an audible warning device intended by the manufacturer or it is not working x 1.10. One of the measuring panel with inventory measurement and indicating devices do not perform its intended function. Do not operate the measuring Panel lighting x 1.11. Implements is not equipped with an emergency stop sign. Emergency stop sign is not the structural damage, provides the ability to mark stable place on the roadway x 1.12. Driving for the technical training is not marked with an identification mark in accordance with road rules x 1.13. On the technical information are situated or that use of the mark with national standards in certain road signs, shapes, color combinations and designs and can mislead other road traffic participants x 1.14. Recognition sign is damaged (e.g. cracks, broken, faded) × II. Light devices 2.1. Implements is not equipped with the lamp manufacturer x 2.2. The dipped and main beam headlamps is set in front of a symmetrically in relation to the implements the median longitudinal plane x 2.3. Lamps installed the same type and manufacturer specific power without the appropriate bulb x 2.4. Implements is not fitted with dipped and main beam lamps x 2.5. Switch on the dipped-beam headlamps do not turn on at all the dipped-beam headlamps, lamps and lighting the plate x 2.6. When you switch on the dipped-beam lights not switch all driving beam headlamps x 2.7. Main-beam headlamps are switched separately and consistently, if not turned on lamps and lighting the plate x 2.8. Implements have set up more than two front fog lamps, they are not set up in front of a symmetrically in relation to the longitudinal median plane or implements implements only one fitted front fog lamp x 2.9. They installed front fog lamps will not turn on at the same time. Fog lights are switched separately, if not turned on lamps and lighting the plate x 2.10. Implements and trailers do not have two red light-emitting rear lamps x 2.11. Turn on the lamps, do not switch on all lamps and lighting the plate x 2.12. Implements and trailers is not white light emitting plate lamp x 2.13. Number of lamps are positioned so as to effectively illuminate the implements and trailers a number sign x 2.14. Number plate lights do not turn on simultaneously with all the lamps x 2.15. Implements is not at least two front and two rear direction indicator lamps at least. Trailers are not at least two rear direction-indicator lamps x 2.16. All direction indicator lamps do not emit yellow light. Other color light-emitting in the direction indicators are permissible only if such lamps are intended installation implements or trailer manufacturer x 2.17. Direction indicator lamps not installed symmetrically in relation to the implements and trailers median longitudinal plane x 2.18. Turn on the right or left side direction indicator lamps, while will not turn on and not blinking all together in the right or left side direction-indicator lamps x 2.19. Emergency alarm mode flashes not all direction indicator lamps simultaneously light x 2.20. Implements and the trailer not equipped with at least two red light emitting braking lamps x 2.21. Implements and trailer brake lamp not mounted in the back, they are not symmetrical in relation to the median longitudinal plane x 2.22. Pressing the brake pedal, the brake light not all lamps. Mounted brake lamp that works in a continuous mode x 2.23. Implements is not two rear reflector red x 2.24. Implements the trailer no two rear triangle reflector in red and two other shapes in front of the reflector in white and orange sides x 2.25. Implements and trailer reflectors are mounted symmetrically in relation to the average trailer or implements garenplakn. The reflector surface damage (such as corrosion, cracks, izlūzum) x 2.26. Implements the lamp is not properly secured to the rigid parts, so while driving uneven roads do not lead to fluctuations of the beam of light x 2.27. The lens is not clean, it has cracks, izlūzum or other nature damage x III. Steering equipment 3.1. The wheel size, design or mount does not correspond to the implements the requirements of the manufacturer x 3.2. The steering wheel is bent, cracked. Connection to the steering wheel shaft is moving. The shell interferes with steering wheel satveramīb x 3.3. Steering wheel play exceeds allowed value x 3.4. Steering wheel in one or both directions are difficult to twist, rotate evenly, not seized. The steering wheel turning angle of the mean as far as the situation is not equal in both directions x 3.5. The steering mechanism is mounted according to the manufacturer's requirements. Mount items have not been tightened accordingly and ensure against atskrūvēšano x 3.6. The technical parts that fastened the steering mechanism is broken, bent, cracked or corroded significantly x 3.7 in. The steering is tight. Dust protection are not fixed or corrupt x 3.8. Steering drive mountings are not tightened and secured against atskrūvēšano x 3.9. Steering drive elements is increased by play. They have damage, deformation or corrosion x 3.10. Rebuilt steering drive (except as provided in the technical and regulatory alterations to trailers, laws) x 3.11. Steering and stiepņ lever mounting elements are not relevant or are not tightened to atskrūvēšano x 3.12. The steering wheel and pedals for stiepņ damage, deformation or play. Made remontmetinājum (except where it is intended by the manufacturer implements) x 3.13. The Steering rods in one of the steering wheel turning angle of touching other parts implements x 3.14. Rebuilt steering rods and levers (except as provided in the technical and regulatory alterations to trailers, laws) x 3.15. Steering knuckle mounting elements are not appropriate and ensure to tighten atskrūvēšano x 3.16. Increase by play or a swivel joints shall remontmetinājum. Carried out repairs not dismantle steering knuckle. Dust guards are damaged or not secured x 3.17. Implements the intended manufacturer power steering does not work or does not provide the necessary efficiency x 3.18. One of the power-steering parts is damaged or not properly mounted. Amplifier components are not airtight. Amplifier working fluid level is lower than the minimum x 3.19. Amplifier system piping or hose to touch moving parts implements x IV. Braking equipment 4.1. Implements or trailer is not equipped with a service braking device (other than a trailer, which the service braking device is not provided by the manufacturer) x 4.2. Implements and trailer brakes do not work on all the wheels equipped with brake mechanisms x 4.3. Service brake does not provide the technical and the braking of the trailer according to the technical rules of the manufacturer x 4.4. Checking the effectiveness of the braking device road conditions, implements a significant deviation from straight-line motion x 4.5. Brake actuators is observed in the brake fluid leak x 4.6. After the brake pedal and pedal unloading it returns to its starting position x 4.7. Brake pedal foot atbalstvirsm is covered with ribbed increase friction material or otherwise secured against slipping. Brake pedal (lever) is cracks, damage x 4.8 Brake pedal, determine or remontmetinājum x 4.9 Implements is not fitted with a parking brake, it does not provide sufficient braking efficiency x 4.10. Pneumatic brake equipment compressor provides the air pressure specified by the manufacturer of the braking device in x 4.11. The observation of the oil spill from the compressor x 4.12. The compressed air cylinder to the implements are not mounted rigidly. It is mechanically damaged, korodēj or with remontmetinājum. Observed air leaks out of the balloon. Dewatering valves do not have a working x 4.13. Damaged air pressure regulator, it is inappropriate. Connections are not sealed x 4.14. The specified mode is not working a pneumatic brake system pressure gauge x 4.15. Rebuilt braking (except as provided in the technical and regulatory alterations to trailers, laws) x v. tires, wheels 5.1. Implements or trailer mounted within the manufacturer's specified requirements inadequate tires x 5.2 in. On the wheels of the same axle installed tires of different sizes x 5.3. Tyres are ply layer atslāņoj atsedzoš damage to the frame, or the side of the tread separated material. Minimum tyre tread depth the technical and the trailer is less than 1.0 mm x 5.4. Wheel tyre and disk the combination does not correspond to the trailer or implements the requirements of the manufacturer x 5.5. Set of wheel disks, which are not manufactured or that the design is changed x 5.6. Nuts and screws do not have the appropriate structures or not tighten x 5.7. Set other brands or models of drives, which differs from the manufacturer's mounting for mounting x 5.8. Implements the trailer wheels or disks is cracks, deformation, izlūzum x VI. Frame (pusrām), engine, clutch, the car and the truck compartment 6.1. Implements and trailer frame (pusrām) is izlūzum, fractures, cracks, deformation and corrosion damage that can affect the structural integrity of the x 6.2. Implements and trailer frame (pusrām) is a superficial corrosion, its structural strength-deformation not x 6.3. Implements in front axle beams has cracks, fractures, deformation, corrosion significantly damage x 6.4 in. By play in front axle beams in rigid connections x 6.5. Implements the engine is not properly secured. Mount items have damage. Protective cover for not adequately secured, they are essential for damage x 6.6. Implements the clutch does not ensure release running up and easy gear changing x 6.7. Clutch pedal leg support surface is covered with ribbed increase friction material or otherwise secured against slipping x 6.8. The clutch pedal, determine major and remontmetinājum in x 6.9 in. Clutch hydraulic or pneumatic actuators are not airtight x 6.10. The clutch or flywheel cover is not properly secured to the x 6.11. Implements transmission, distribution boxes, or differential lock is not properly mounted or does not perform the intended function on or off with difficulty x 6.12. Increase the kardānpārvad of joints shall play and creating intermediate support x 6.13. Kardānpārvad elements is not properly secured. They have fractures, cracks or deformation x 6.14. Engine lubrication or cooling system is not airtight. Increased oil leak from the transmission x 6.15. Implements or trailer is not equipped with the design of the coupling or hitch x 6.16. The coupling or hitch used improvised coupling device. The coupling or hitch spiral connection is not properly tighten x 6.17. The technical hitch or place devices is increased wear caused by play x 6.18. Hang the coupling or device stiepņ, bars, or other elements are fractures, cracks, deformation, corrosion, damage or significantly remontmetinājum (except where it is provided by the manufacturer) x 6.19. Change the cabin structure implements (except as provided in the technical and regulatory alterations to trailers, laws) x 6.20. Cab mounts are affecting the strength of mechanical damage, deformation or corrosion damage x 6.21. Implements booth (cabin) is driving the cumbersome elements. The internal equipment is properly secured to the x 6.22. Not supported by the technical design of the wheel guards x 6.23. The cab steps is corrosion damage and deformation x 6.24. The cab steps are not covered with special friction material of aggravating or made with a ribbed surface, which reduces the chance of foot slip x 6.25. Implements the cab door or hood is not fitted with an opening mechanism laid down by the manufacturer, handles, latch. A door or the hood is not properly secured, difficulty closing or opening of x 6.26. The requirements laid down by the manufacturer, not the glass x 6.27. Implements the windshield is the visibility of the troublesome injury or meadows x 6.28. Wiper is not properly secured or not working in all modes for x 6.29. Wiper blades are damaged, they do not provide effective cleaning glass x at 6.30. Does not work in the design of the glass washer x 6.31. Implements is not fitted with design seats. Seats not by manufacture or according to the fixed. The seat adjustment and locking devices are not in working order x 6.32. The technical design is not equipped with safety belts provided for x 6.33. The seat belt is not properly secured, it is with damage, cracks, izdilum. Locking device is not on the agenda x 6.34. Heating equipment (ventilation) does not work in all modes for x 6.35. Implements is not delivered with design of work equipment and auxiliary equipment x 6.36. Implements the PTO, or other rotating elements are not provided with the protector or protectors x 6.37. Implements and its trailer has a hydraulic system elements is not fixed according to the requirements of the manufacturer. They are touching implements or trailer all rotating parts x 6.38. Installed in the hydraulic system elements, which are not manufactured or that the design is changed. The elements of the system have cracks, izlūzum or deformation affecting system security x 6.39. Oil leakage from hydraulic system elements x 6.40. Trailer flooring is, through x izrūsēj 6.41. Load compartment is damaged the shut and locking elements x 6.42. Do not set the trailer safety chain (rope) (except a trailer fitted with air brakes, which rupture in a trailer in braking) x 6.43. Trailer safety chain is mechanical damage x VII. Feeding system, electrical system 7.1. Implements is not equipped with the fuel tank manufacturer in x 7.2 in. The fuel tank is damaged, deformed, korodējus. The fuel tank is not properly secured. Fastening elements are deformed, corroded, loosely. Observed fuel leak x 7.3. Fuel supply device and system units are damaged or not secured in accordance with the requirements of the manufacturer. Observed fuel leaking from the fuel-feed system x 7.4. The accelerator control its release free returns to its original position (except the hand control Accelerator) x 7.5. Electrical wiring is not properly secured, they have damaged insulation x 7.6. Used improvised, adapted or repaired fuses x 7.7 in. Implements the coupling device is not equipped with a special socket or the trailer coupling device is not appropriate for the plug for the trailer lights for the operation of the devices. Jack (the plug) or anchorage is not damage, trailer light set the operation mode, it is not a fixed position or connected connected arbitrarily disconnect x 7.8. Battery the battery is not rigidly fixed, or it is held firmly in place, which it implements affect the driver's field of vision and identification and control devices. Battery terminals are damaged, their connection to the power wires are not rigid or x 7.9 with starpelement. The specified mode is not working implements designed to lock in starting the engine the machine x VIII. Exhaust system 8.1. Exhaust system design does not ensure compliance with the permissible noise level x 8.2. The exhaust system is not adequately secured, they come into contact with the brake or fuel pipelines, equipment as well as electrical wires x 8.3. Is the damage that causes exhaust leak or exhaust system affects the strength of x 8.4. Considerable engine oil combustion, if the engine warm up to operating temperature x 8.5. Implements the generated noise, it still stands on the site, exceed the level stated by the manufacturer, or 80 ± 2 dB x ' in place of the Prime Minister, Defense Minister a. Pabriks, Minister of Agriculture of Rapidity.