Cabinet of Ministers Regulations No. 144 in Riga 2003. April (1. No 18, § 13) the rules on the rest of the shipbuilding, the assessment of conformity and placing on the market are Issued in accordance with the law "on conformity assessment" article 7 of the first and the second part 1. General questions 1. determines the rest of the vessel design and construction safety requirements applicable to the offering on the market, as well as the rest of the vessel conformity assessment procedures.
2. Recreational craft is any sport and recreation for the ship (regardless of engine type) hull length from 2.5 to 24 m, measured according to the standards, except for the adapted: 2.1 craft intended solely for racing, including rowing racing boats and training rowing boats, which are labelled appropriately shipbuilder;
2.2. canoeing, kayaks, gondolas and water bikes;
2.3. sailing surfboards;
2.4. powered surfboards and other similar self-propelled vehicles;
2.5. the original and individual historical vessels models designed and built before 1950 are mostly from the original materials and the Builder is labelled accordingly;
2.6. the pilot vessels, if they are not offered in the market later;
2.7. the vessels built for personal use, if for the next five years they will not be placed on the market;
2.8. vessels intended to provide service to carry passengers for commercial purposes, regardless of the number of passengers;
1.8. submarine vessels;
2.10. air-cushion vehicles;
2.11. hydrofoils.
3. recreational vessels are chartered or used in the training of boatmasters, subject to all the requirements of this regulation if the vessel is offered for the rest of the market.
4. these provisions shall apply to recreational craft, partly completed boats and components of the design (both built-in and stand-alone), referred to in paragraph 5 of these rules.
5. Recreational craft design components are the following: 5.1 the equipment all the built-in pretaizdegšan and boarding engines;
5.2. protection against engine being all boarding engines;
5.3. Steering, steering mechanisms and cable assemblies;
5.4. fuel tanks and fuel hoses;
5.5. manufactured hatches and scuttles.
6. The provisions referred to in paragraph 4, the product conforms to the safety, health, environmental protection and consumer protection requirements set out in section 2 of these regulations.
7. The Ministry of transport, in cooperation with the relevant technical standards Committee recommends the non-profit State limited liability company "Latvian standards", reliance standard.
8. the non-profit organization public limited liability company "Latvian standards" submit for publication in the newspaper "journal" the harmonized European standards and national standards list, check after the constructor can be applied to comply with these regulations (hereinafter referred to as adapted standards).
2. the rest of the vessel design and construction safety requirements 9. Depending on the design of the rest of the ships are divided into four categories: category A 9.1 "the ocean" – designed for long journeys, if the wind force 8 (Beaufort scale), wave height: 4 metres;
9.2. Category B "open sea" – designed for voyages on the high seas, if the wind strength is up to 8 balls (including), wave height — up to 4 metres;
9.3. Category C "coast" — designed for voyages in coastal waters, large bays, river sources, lakes and rivers, where the wind strength is up to 6 balls (including), wave height up to 2 metres;
9.4. Category D "Protected waters" — designed trips Lakes, rivers and canals when wind strength is up to 4 balls (including), wave height up to 0.5 meters.
10. The category of recreational vessels designed and built in such a way that they comply with the rules set out in point 9 of category criteria in respect of stability, buoyancy, and other requirements laid down in this chapter and to have good handling characteristics.
11. To the rest of the hull in put: 11.1. recreational craft identification number according to adapt standards to include the following information: 11.1.1 the constructor code;
11.1.2. the Builder;
11.1.3. serial number;
11.1.4. year of construction;
11.1.5. model year;
11.2. Builder's plate with the following information: the name of the Builder; 11.2.1.
11.2.2. the CE marking according to this provision the provisions of Chapter 8;
11.2.3. the category under this provision 9. the criteria set out in paragraph 1;
11.2.4. the maximum load the Builder according to this provision, paragraph 21;
11.2.5. the number of persons stated by the Builder, the carriage of which the ship is intended.
12. Depending on the category of the recreational craft shall be so constructed as to reduce the risk of falling overboard and facilitate boarding the ship.
13. A Person who runs a recreational vessel from the ship's main control site under normal conditions (taking into account the speed and load) will ensure a good visibility in all directions.
14. To the rest of the ship's owner's manual provided in the national language. In this guide, in particular fire and flooding risks and include the information referred to in paragraph 11.2 of these regulations, and in paragraph 21.
15. Recreational craft material choice and design provides the connectivity to the rest of the ship would be strong enough and matched it to the category in accordance with paragraph 9 of these regulations and of the Builder's recommended maximum load in accordance with the provisions of paragraph 21.
16. the Rest of the ship, on account of its category in accordance with paragraph 9 of these regulations and of the maximum load recommended Builder in accordance with paragraph 21 of these rules is sufficient stability and free board height.
17. Building the rest of the body, ensure that the vessel would have the buoyancy characteristics appropriate to its category in accordance with paragraph 9 of these regulations and of the Builder's recommended maximum load in accordance with the provisions of paragraph 21.
18. All the rest apdzīvojamo daudzkorpus ships built in such a way as to ensure buoyancy also overturned intact above the water. Recreational vessels the length of which does not exceed six metres and which can quickly fills with water, provided with buoyancy.
19. Hull, deck and superstructure openings must not affect the rest of the ship's watertight integrity of structural integrity or integrity of these openings close. Windows, Windows, doors and hatch covers to withstand the water pressure, which is possible, given their location, as well as pressure from the weight of people moving on deck. Hull openings that allow water into the casing and scattering from it and below the waterline corresponding to the maximum load recommended Builder in accordance with paragraph 21 of these regulations, is fitted with an easily accessible means of closing.
20. Recreational vessel designed and built in such a way as to minimize the risk of sinking, paying special attention to: 20.1. kokpit and sumps which must be pašdrenējoš, or other means which prevents water from entering inside;
20.2. the ventilation equipment;
20.3. the water evacuation, using pumps or other means.
21. the maximum load recommended construction (including fuel, water, food, miscellaneous equipment and people (in kilograms)), a recreational craft is designed and specified to the constructor of the plate shall be based on the category in accordance with paragraph 9 of these regulations, stability and free onboard height in accordance with the provisions of paragraph 16 and buoyancy in accordance with the provisions of paragraph 17.
22. All category A and B, as well as C and D category, which is more than six metres, shall be equipped with one or more easily accessible to the liferafts. Raft size corresponds to a number of people, one vessel can carry according to its design and construction recommendations.
23. Apdzīvojamo daudzkorpus rest of the vessels that are longer than 12 metres, equipped with rescue facilities to the roll of the ship or fire.
24. Recreational craft, given the category and characteristics, shall be fitted with one or more ropes, or strengthening other means that could safely withstand the appropriate anchor, tethering and towage.
25. The constructor shall ensure that the ship would be satisfactory for the driving characteristics, using the most powerful engine to which the rest of the ship is designed and built. Recreational craft engine maximum power indicates the owner's manual in its nationally recognized standards, the ship is built.
26. The built-in engines placed on a partition that is separate from the living quarters to reduce the fire or fire spread risk, as well as to reduce the danger of living places, caused by toxic smoke, heat, noise or vibration.
27. details of the Engine and ancillaries required often to check and serve, is readily available.
28. the insulating materials inside engine compartment must not be flammable.
29. The engine compartment is ventilated and prevent water from entering through the compartment openings.
30. Open engine hot or moving parts that can injure people, effectively covers, unless the engine is protected by a shell, or shell.

31. the rest is boarding the vessels engine, you need a device that prevents starting the engine when the gearbox is in neutral position, except in the following cases: 31.1. engine generates a static thrust of less than 500 newtons (N);
31.2. the engine is equipped with a throttle opening limiting device for starting the engine at the moment does not allow static thrust, more than 500 n. 32. Filling, storage, ventilation and feeding equipment designed and installed so as to minimize the risk of fire and explosion.
33. fuel tanks, pipes and hoses are separated or protected from any significant source of heat. Tank fabrication materials and their design meets the capacity and fuel type. All compartments are ventilated containers.
34. The liquid fuel with a flash point lower than 55 ° C, stored in tanks which do not form part of the ship's hull and are: 34.1. separated from the engine compartment and from all other source of ignition;
21.3. separated from living quarters.
35. The liquid fuel with a flashpoint above 55 ° C or, you can store the containers which are part of the hull.
36. The electrical system is designed and installed so as to ensure the proper operation of recreational vessel under normal conditions of use and to reduce the fire and electrical shock hazard.
37. The electrical system is designed and installed so as to ensure that all circuit protection against overload and short circuits, except engine starting circuits that use a battery.
38. The electrical system has ventilation to prevent the accumulation of gases that can be released from batteries.
39. The batteries are firmly secured and protected from water penetration.
40. the management system is designed, constructed and installed so as to ensure the management team putting the foreseeable operating conditions.
41. Sailing ships and recreation recreational vessels with one engine and built-in remote steering system equipped with driving the ship's emergency management means that ships could run at a reduced speed.
42. the gas system, intended for use on recreational craft, ensure steam drain. They are designed and installed so as to prevent spill and explosion risk and leakage testing is available. Gas system components and materials are suitable for gas and resistant to the marine environment caused by voltage and exposure.
43. each gas appliance is equipped with a pretuzliesmošan facility, which is valid for all types of burners. Any equipment that consumes gas, supplied by a separate branch of the distribution system and locked by a separate closing device. To prevent gas leaks and combustion products of injury, provide adequate ventilation.
44. ships with permanent built-in gas system is fitted with a closed compartment to hold the gas cylinder. Partitions separated from living quarters, they are only available from the outside and ventilated to the outside so that the gas spilling out of the deck. Permanently integrated gas system after its installation.
45. choosing the type and layout of equipment on board, having regard to the risk of fire and its spread. Special focus on devices with an open flame (ensure that it is in close proximity to flammable objects), engines, auxiliary machinery and mechanism of the hot zones (not deploy the wiring over them), as well as uncovered in oil and fuel pipes (prevents oil and fuel overflows).
46. Recreational craft shall be supplied with appropriate fire-fighting equipment. Gasoline engine compartment shall be protected with fire-extinguishing system, which eliminates the need to open the compartments in the event of fire. Portable fire extinguishers installed in easily accessible places, one of them is placed so that it is easy to reach from the main control board.
47. The rest of the ship's navigation lights comply with the 1972 Convention on 20 October the international vessel collision prevention regulations (COLREG-72) or the European inland navigation code (CEVN).
48. Recreational craft built in such a way as to prevent the release of contaminants (e.g., oil, fuel) accidental discharges outside the Board.
49. For recreational craft fitted with toilets requires the adoption of port equipment completely emptied the toilet contents collection system (linked to the sanitary equipment, including a toilet, hoses, pipes, storage tank and deck connection suitable for the collection, storing and channelling waste water). May also be used to move a toilet and the accumulation tank, if it can empty the coast making equipment. Toilet content collection systems shall satisfy the following conditions: 49.1. the toilets installed on Board of the content acquisition system designed according to international standard ISO 8099;
30.6. the technical requirements for holding tanks and drain hoses are: 49.2.1. pipe diameter depending on the tank in accordance with the international standard ISO 8099 is such as to withstand the pressure of the suction pipe. If necessary, the pipe shall be fitted so as to allow the use of air injection method through the opening in the tank that is open during evacuation;
49.2.2. using a specific type of hose, which prevents odors, if hose waste remains;
30.6. the technical requirements for the connection Board are: 49.3.1. discharged from the deck using the connection with a 38 mm opening, but if it is internally threaded, use the threaded G11/2 in accordance with the international standard ISO 228-1 can also be used in connection with the 45 mm and 50 mm Aperture;
49.3.2. deck connection is indicated by the corresponding international standards organisation (ISO) symbols;
49.3.3. Board connection hose extends at least 300 mm from the Board directly connected;
49.3.4. deck connection is set up in accordance with the manufacturer's instructions;
49. the permanent or transportable storage tanks use only marine environmental chemicals.
50. the pipes passing through the hull of the ship and for wastewater discharge from the impoundment of water tank directly, in accordance with the terms of discharge is secured.
3. Recreational craft and their components design offering the market 51. the notified body shall take the necessary measures to ensure that the rules laid down in paragraph 4, the products are properly constructed and maintained, can offer the market and put into service according to its intended purpose only if they do not endanger the safety and health of persons, property or the environment. 52. Latvia is not prohibited, restricted or impeded the provision laid down in paragraph 4, the placing on the market of the products and commissioning If they are labelled with the CE mark, which granted the authorized institution, and they meet the requirements of these rules, including compliance with the procedures provided for in Chapter 6 of the provisions.
53. in Latvia it is not prohibited, restricted or impeded the partly completed recreational craft of offering on the market, if the Builder, his authorized representative (in Latvia) or the person responsible for placing on the market, in accordance with the provisions of paragraph 54, declares that the rest of the ship's construction will be completed.
54. The provisions referred to in paragraph 53 of the Builder, his authorized representative (in Latvia) or the person responsible for the placing on the market, the Declaration shall include the following information: 54.1. the representative of the Builder, the Builder (Latvia) or the person responsible for the placing on the market, the name and address;
54.2. partially completed ship;
54.3. a statement that the partly completed construction of the vessel will be completed and that the ship complies with this construction applicable requirements.
55. in Latvia it is not prohibited, restricted or impeded the provision laid down in paragraph 4, the design of components covered by the market and the putting into service, if they are marked with the CE mark, which granted the authorized institution, and these components are intended to be incorporated in the rest of the ships in accordance with the provisions laid down in paragraph 56 of the Declaration, which shall be sent to the Builder, his authorized representative (in Latvia), or who these components offer the Latvian market.
56. The Builder, his authorized representative (in Latvia) or persons ingredients offers a market of Latvia, the Declaration shall contain the following information: 56.1. the representative of the Builder, the Builder (Latvia) or persons ingredients offers a market of Latvia, name and address;
56.2. Description of components;
56.3. a statement that the component complies with the relevant requirements.
57. The provisions referred to in paragraph 4, the products which do not comply with the requirements of this regulation are allowed to expose the exhibitions, fairs and other events, if the mark is clearly visible in the clear that this product trading and commissioning is only allowed by their compliance in accordance with these rules.
4. Warranty conditions

58. If the rules referred to in paragraph 5 of the structure the components or recreational vessels that have the CE marking and which is properly constructed, installed, maintained and used in accordance with the intended purpose, may compromise the safety and health of persons, property or the environment, the market surveillance authorities within their respective fields of competence, take measures to remove them from the market, prohibit or restrict the placing on the market or putting into service. The market surveillance authorities shall promptly inform the authorized institution of the said measures, specifying the reasons for its decision, especially where non-compliance is due to this provision, paragraph 6 of the non-compliance.
59. If the rules referred to in paragraph 5 of the structure or vessel is marked with the CE mark, but does not meet the requirements laid down in these rules, the notified body, which controls the person who affixed them, take appropriate measures and inform the consumer centres.
5. Conformity assessment procedures 60. This provision Before the manufacturer launched the vessel referred to in paragraph 4 and their components production and placing on the market, he or his authorized representative (Latvia) takes into account this provision in Chapter 5 and 6 in accordance with the requirements set out in paragraph 9 of these regulations set out the categories of recreational craft.
61. the rest of the categories A and B vessels with a hull is shorter than 12 metres, take the internal production control plus tests (module Aa) under this rule 6.2. Subdivision.
62. the rest of the categories A and B vessels with a hull length from 12 to 24 metres, take the CE test sample (module B) pursuant to this provision, subsection 6.3 supplemented by consistency (C module) or any of the modules B + D, or B + F, or G, or H. 63. category (C) recreational craft, hull length from 2.5 to 12 metres : 39.2. If compliance with this provision. 16 and 17 above standards regarding stability, free port and buoyancy, take the internal production control (module A) according to the provisions of subsection 6.1 of these conditions;
39.3. If these provisions are not complied with 16 and 17 above standards regarding stability, free port and buoyancy, take the internal production control plus tests (module Aa) under this rule 6.2. Subdivision.
64. the rest of the category C vessels with a hull length from 12 to 24 metres, take the CE test sample (module B) pursuant to this provision, subsection 6.3 supplemented by consistency (C module) or any of the modules B + D, or B + F, or G, or H. 65. Category D recreational craft, hull length from 2.5 to 24 metres, take the internal production control (module A) according to the provisions of subsection 6.1 of this conditions.
66. Recreational craft construction materials used in one of the modules B + C, or B + D, or B + F, or G, or H. 6. Conformity assessment procedures 6.1. Internal production control (module A) 67. Builder or his authorized representative (in Latvia) provides the products concerned are in conformity with the requirements of this regulation. Builder whose product marked with the CE mark, or his authorized representative (in Latvia) draws up a written declaration of conformity in accordance with the provisions of Chapter 9.
68. technical documentation prepared by the Builder he or his authorized representative (in Latvia) kept for at least ten years after the last product has been manufactured. These documents are available for inspection bodies to carry out inspections.
69. where the Builder or his authorized representative is located in Latvia, the technical documentation a person who distributes the product market of Latvia.
70. the product is in conformity with the requirements of these provisions valued at technical documentation, which includes the product design, production and operation, according to the description of the rules in Chapter 7.
71. the Builder or his authorized representative shall keep a copy of the Declaration of conformity with the technical documentation.
6.2. Internal production control tests (module Aa, option 1) 72. Internal production control with the addition of A test module requires that the recreational craft shall take one or more tests for stability and buoyancy properties according to the requirements of these regulations or equivalent calculation or control.
73. This provision 72. the tests referred to in paragraph 1 or the equivalent calculation or control responsibility of the notified body, chosen by the Builder.
6.3. the CE test sample (module B) 74. Authorized institution ensure and attests that a specimen, representative of the production envisaged, meets the requirements of these regulations.
75. the application to check the CE Model Builder or his authorized representative (in Latvia) submitted to the notified body of his choice. The application shall include the following information: 75.1. the name and address of the Builder (if the application is lodged by the authorised representative, the representative's name and address);
75.2. a written declaration that the application has not been lodged with any other notified body;
75.3.79. these provisions referred to in technical documentation.
76. The applicant shall forward to the notified product model authority (hereinafter sample).
77. The sample may cover several versions of the product provided that the differences between those versions do not affect the level of safety and the other requirements relating to a product.
78. If necessary, the notified body may request further samples, to carry out the test programme.
79. The technical documentation shall enable the conformity of the product with the requirements of this regulation. It includes (to the extent necessary for such assessment) product design, manufacture and operation of the description in accordance with the provisions of Chapter 7.
80. the notified institution: 80.1. examine the technical documentation, verify that the model is built in accordance with the technical documentation and identify the components of the structure which are and which are not constructed in accordance with the adapted standards for which there are published references to the official;
80.2. carry out appropriate inspections and tests necessary to check that the Builder, the solutions adopted meet the requirements of the rules, if not the adapted standards applied;
49.9. take appropriate and necessary tests to check whether the selected construction standards have been applied;
80.4. agree with the applicant on the inspection and verification of the required tests.
81. If the sample meets the requirements of this regulation, an authorized institution shall issue to the applicant a CE certificate samples. The certificate shall contain the name and address of the Builder, the conclusions of the examination, the conditions of validity and the information necessary to identify the approved sample.
82. The certificate is added to the relevant parts of the technical documentation. A copy shall be deposited with the notified body that issued the certificate.
83. If the constructor are rejected sample certification institution authorized detailed to justify the refusal.
84. The applicant shall inform the notified body that holds the technical documentation concerning the CE examination certificate, the model for changes to the approved product which requires additional approval where such changes may affect compliance with the requirements or conditions of use of the product described. Additional approval is given in the form of an addition to the CE examination certificate of the sample.
85. Each notified body shall give the other notified bodies the necessary information on the CE sample examination certificates and certificates issued or refused the supplements.
86. The other notified bodies may receive CE sample examination certificates and their additions. The annexes to the certificates are available to the other notified bodies.
87. the Builder or his authorized representative shall keep the sample in CE examination certificate and its additions with the technical documentation a copy of at least ten years after the last product has been manufactured.
88. where the Builder or his authorized representative is located in Latvia, technical documentation, which markets products in Latvia.
6.4. Consistency (C module) 89. Builder or his authorized representative (in Latvia), ensures and declares that the products concerned conform to the pattern described in CE sample examination certificate and satisfy the requirements of this regulation. Builder highlights each of the CE marking to the product and draw up a written declaration of conformity.
90. The shipbuilder shall take the necessary measures to ensure that the manufacturing process ensures conformity of the products produced, which described the model CE examination certificate and the requirements of these regulations.
91. the Builder or his authorized representative shall keep a copy of the Declaration of conformity for at least 10 years after the last product has been manufactured.
92. where the Builder or his authorized representative is located in Latvia, technical documentation, which markets products in Latvia.
6.5. the product quality assurance (module D)

93. Builder ensures and declares that the products concerned conform to the pattern described in CE sample examination certificate and comply with the requirements of this regulation. The Builder or his authorized representative (in Latvia) marked each product with the CE marking and draw up a written declaration of conformity. The CE marking supplemented by the notified body identification number, which took the rule laid down in paragraph 104.
94. the Builder supports this provision in subsection 6.6 the quality system and abide by these rules laid down in paragraph 104.
6.6. the quality system 95. to evaluate the quality system builder submitted the application, the institution authorized to include: 95.1. information about expected product category;
95.2. documentation concerning the quality system;
95.3. If necessary, the technical documentation of the approved sample according to Chapter 7 of these rules and the requirements of the CE examination certificate sample copy.
96. the quality system shall ensure compliance of the product sample as described in sample CE examination certificate and with the requirements of this regulation.
97. the elements of the quality system requirements and conditions accepted by the constructor, systematically documented, presenting them as written plans, procedures and instructions. The quality system documentation shall ensure the quality programmes, plans, manuals and protocols for common understanding.
98. quality system documentation includes: 98.1. quality objectives and the organizational structure, responsibilities and powers of the management with regard to product quality;
98.2. manufacturing, quality control and quality assurance techniques and processes;
98.3. the examinations and tests that will be carried out before construction, during and after, as well as the frequency of the conduct;
98.4. quality records (such as inspection reports and test messages, calibration, qualification reports of the personnel concerned);
98.5. the requested product features quality monitoring and effective operation of the quality system.
99. the notified body shall assess the quality system compliance with the requirements of this regulation. The notified body assumes that its quality systems which implement the adaptēto standard meets these requirements.
100. the quality system conformity assessment group has at least one person with experience in the relevant product technology concerned. The assessment procedure includes a visit to the manufacturer's premises.
101. The decision shall be communicated to the constructor. The notification shall contain the conclusions of the examination and assessment.
102. the Builder undertakes to fulfil the obligations arising out of the approved quality system, and maintain the quality system adequate and efficacious.
103. the Builder or his authorized representative shall inform the notified body of any planned quality improvement of this system. The notified body shall evaluate the modifications proposed and decide whether the premium quality system complies with the requirements of this regulation or repeated assessment is required. The notified body shall notify its decision to the constructor. The notification shall contain the conclusions of the examination and the grounds for the decision.
104. the notified institution: 104.1. the audits to make sure that the Builder duly fulfils the obligations arising out of the approved quality system;
104.2. conformity assessment periodically checks to make sure that as the Builder is maintaining and applying the quality system. The notified body shall submit the audit report to the Builder;
104.3. without warning can perform extraordinary inspection. During such inspections, the notified body may carry out tests or have them carried out, to check the quality of the system. The notified body shall submit the inspection report and the Builder, if the testing has taken place, and the test results.
105. to the notified body for inspection, the Builder provides the notified body free access for construction, inspection, testing and storage locations and provide all required information including: 105.1. quality system documentation;
105.2. quality records (inspection reports, test and calibration results, qualification reports of the personnel concerned).
106. Ten years after the last product has been manufactured, keep at the following constructor of control bodies available documents: 106.1. the quality system documentation;
106.2. documentation on the quality system improvements;
106.3. decisions and notified bodies of reports on the compliance of quality system standards, adapted for periodic audits and for the additional tests. the Builder
4.2. product inspection (module F) 107. This module describes the procedure whereby the manufacturer or his authorized representative (in Latvia) checks and attests that the products subject to the requirements of this regulation, shall conform to a model that describes the sample CE examination certificate and with the requirements of this regulation.
108. the manufacturer shall take necessary measures for the manufacturing process ensures conformity of the sample described CE sample examination certificate and with the requirements of this regulation. The manufacturer or his authorized representative (in Latvia) marked with the CE mark to each product and draw up a declaration of conformity.
109. the notified body shall carry out appropriate inspections and tests to check the conformity with the requirements of this regulation. Check after the choice of the manufacturer: 109.1. examining and testing every product in accordance with the provisions of paragraph 111;
109.2. checking and testing the products by statistical methods in accordance with the provisions of paragraph 112.
110. the manufacturer or his authorized representative shall keep a copy of the Declaration of conformity for at least 10 years after the last product has been manufactured.
111. the inspection and testing of the product: the product of the individual test 111.1. and tests set out in the standards adapted, or equivalent tests, to ensure that the product is in conformity with the type as described in the sample of the CE examination certificate and with the requirements of this regulation;
111.2. authorized institution to be affixed, its identification number to each approved product and draw up a written certificate of conformity concerning the tests carried out;
111.3. the manufacturer or his authorised representative shall ensure that the notified bodies the conformity certificates issued are available on request.
112. statistical verification: 112.1. the manufacturer shall present his products as a uniform group, and take measures to ensure that the manufacturing process each group produced uniformity;
112.2. all products shall be available for inspection in a uniform group. Choose from each group. The model of individual product inspection and tests performed, which certainly adapted in the standards, or equivalent tests, to ensure that the product is in conformity with the requirements of this regulation and to determine whether the group is validated or rejected;
112.3. statistical inspection, the following elements: 112.3.1. statistical method;
112.3.2. the sampling plan with its characteristics of the implementation;
112.4. If product is approved, the authorized institution to be affixed, its identification number to each product and draw up a written certificate of conformity relating to the tests carried out. All products in the group can offer the market, except those who were identified as non-compliant;
If the product group 112.5. is rejected, the notified body or by the market surveillance authorities shall take appropriate measures to prevent the sale of this product on the market;
If the product group 112.6. has been rejected several times, the notified body may void the results of statistical tests;
If the notified body 112.7. responsibility, the manufacturer may affix the body's identification number during the manufacturing process;
112.8. the manufacturer or his authorised representative shall, on request, be produced to the authorized authorities issued certificates of conformity.
6.8. the unit verification (module G) 113. This module describes the procedure whereby the Builder ensures and declares that the product concerned, which has issued the certificate referred to in paragraph 115, meeting the requirements of this regulation. The Builder or his authorized representative (in Latvia) affix the CE marking to the product and draw up a declaration of conformity.
114. the notified body shall examine each product and carry out the tests laid down in the standards adapted, or equivalent tests, to check the conformity of the products with the requirements of this regulation.
115. the notified body shall affix its identification number to the approved product and shall draw up a certificate of conformity relating to the tests carried out.
116. The technical documentation shall enable the conformity of the product with the requirements of these provisions and provide an explanation of the product's design, manufacture and use.
4.3. Full quality assurance (module H) 117. This module describes the procedure whereby the Builder, which performs the duties referred to in the rules, ensures and declares that the products concerned meet the requirements of these regulations applicable to them. The Builder or his authorized representative (in Latvia) affix the CE marking to each product and draw up a written declaration of conformity.

118. The CE marking supplemented by the notified body identification number, which is responsible for this rule set in 130 CE test.
119. the Builder supports this rule 6.10. sub-chapter quality system with respect to the product's design, manufacture and final inspection and testing, as well as the supervision order is subject to the rules laid down in paragraph 130.
6.10. the quality system 120. to evaluate the quality system, the manufacturer shall submit to the institution of the application, the authorized which shall include information on the expected products and quality system documentation.
121. the quality system shall ensure compliance of the products with the requirements of this regulation.
122. the elements adopted by the manufacturer, the requirements and the conditions for systematic document, presenting them as written plans, procedures and instructions.
123. the quality system documentation shall ensure a quality policy, procedures, quality programmes, plans, manuals and protocols for common understanding.
124. the quality system documentation includes: 124.1. quality system objectives and structure, responsibilities and powers of the management with regard to design and product quality;
technical instructions, 124.2. including the standards which will be applied (if standards were not applied in full, the means that will be used to ensure that requirements are met);
124.3. control and construction design verification techniques, processes and actions that apply to the product category;
124.4. the corresponding manufacturing, quality control and quality assurance techniques, related to the processes and systematic actions;
124.5. the examinations and tests that will be carried out before, during and after manufacture, and inspection and testing frequency;
124.6. quality records (such as inspection reports and test messages, calibration, qualification reports of the personnel concerned);
124.7. features of the required design and product quality monitoring and effective quality system.
125. the notified body shall assess the quality system to determine its compliance with this provision, 121 122 123 and 124, the requirements set out in paragraph and assumes that a quality system which implements the adapted standard meets these requirements.
126. the conformity assessment expert team has at least one person with experience in the product technology concerned. The assessment procedure includes a visit to the manufacturer's premises.
127. the decision shall be notified to the manufacturer. The notification shall contain the conclusions of the examination and assessment.
128. The manufacturer shall undertake to fulfil the obligations arising out of the approved quality system, and maintain the quality system adequate and efficacious.
129. the manufacturer or his authorized representative shall inform the notified body of any planned quality improvement of this system. The notified body shall evaluate the modifications proposed and decide whether the premium quality system complies with these provisions 121.122, 123, 124 and the requirements set out in paragraph or repeated assessment is required. The notified body shall notify its decision to the manufacturer. The notification shall contain the conclusions of the examination and the grounds for the decision.
130. the notified institution: 130.1. checks to make sure that the manufacturer duly fulfils the obligations arising out of the approved quality system;
130.2. periodically carry out audits to make sure that the manufacturer maintains and applies the quality system. The notified body shall provide the manufacturer with audit reports;
130.3. without warning can make the manufacturer's inspection. During such inspections, the notified body may carry out tests or have them carried out, to check the quality of the system. The notified body must provide the manufacturer with an inspection report and, if a test has taken place, and the test results.
131. the authorized institution To perform the test, the manufacturer shall allow the notified body free access to design, manufacture, inspection, testing and storage locations and provide all required information including: 131.1. quality system documentation;
131.2. quality records, relating to the construction (the results of analyses, calculations, tests);
131.3. quality records that are related to the production (inspection reports, test and calibration results, qualifications of the personnel concerned ones).
132. Ten years after the last product has been manufactured, keep at the manufacturer of such control bodies available documents: 132.1. quality system documentation;
132.2. documents on quality system improvement;
132.3. the notified bodies decisions and reports on compliance with the quality system standards, adapted for periodic audits and on additional inspections of the manufacturer.
133. Each notified body must, on request, give the other notified bodies information on issued and withdrawn the approval of the quality system.
7. The manufacturer's technical documentation submitted 134. Modules A, B, C and D referred to in the technical documentation includes information, and the way the manufacturer provides the constructive components of vessels and their compliance with the requirements.
135. technical documentation provides information about the product's design, manufacture, installation and operation and assess compliance with the requirements of this regulation.
136. in order to carry out the evaluation, the technical documentation includes: 136.1. General description of the sample;
136.2. conceptual design and components, Assembly parts, chains, and other elements of the drawings and diagrams and the explanatory descriptions and instructions for use of the product;
136.3. adapted a list of the standards applied in full or in part, and descriptions of the solutions adopted to meet the requirements of this regulation if the adapted standards do not apply;
design and calculation of 136.4. results of checks;
136.5. test results or estimates regarding stability in accordance with paragraph 16 of these terms and conditions of the buoyancy in accordance with the provisions of paragraph 17.
8. the CE marking 137. Holiday craft and this provision in paragraph 5 that the design of the components which comply with the provisions of paragraph 6 of these requirements by offering market, marked with the CE marking.
138. the CE marking (annex) located on the Recreation Board Builder's plate, and this provision set out in paragraph 5 of the structure components and their packaging. The CE marking is clearly visible, legible and indelible. The CE marking is accompanied by the identification number of the notified body, which introduced a Aa, (D), (F), (G) and (H) the procedures in the module.
139. it is prohibited to place on the Board of marks or inscriptions which are likely to mislead third parties as to the meaning or form of the CE marking. Other signs can be placed on a recreational craft and the rules set out in paragraph 5 of the structure components and their packaging provided that the visibility and legibility of the CE marking is not thereby reduced.
140. If a notified body establishes that the CE marking is positioned incorrectly, the manufacturer or his authorized representative (in Latvia) is obliged to end the infringement.
141. If further failure to comply with the requirements set out in these rules for the labelling of the product, the notified body shall take measures to limit or prohibit the placing on the market of such products, or to ensure that it is withdrawn from the market, subject to this provision in the chapter 4 requirements.
9. the written declaration of conformity 142. written declaration for the rest of the Board and the rules laid down in paragraph 5 of part of compliance with this rules is located on the Recreation Board and is connected to the ship's owner's manual.
143. The written declaration of conformity shall include the following: 143.1. the manufacturer or his authorized representative (in Latvia) name and address;
143.2. recreational craft or components of the structure;
143.3. adapted standards or references to instructions, in accordance with which conformity is declared;
143.4. If necessary, information on CE sample examination certificate issued by a notified body;
143.5. name and address of the institution;
143.6. personal data, the signatory who has been empowered to represent the manufacturer in Latvia;
143.7. manufacturer's representative Company (name and address). Authorised representative of the manufacturer's company provides name and address;
143.8. where necessary, the construction of the product description, model, and serial number.
144. the written declaration of conformity is issued in the language of the country.
10. the notified body 145. traffic Ministry newspaper "journal" publishes the list of bodies authorised to carry out the provisions referred to in Chapter 5 of the conformity assessment procedures of any relevant institutions in tasks are mandated to take and what their ID number.
146. the notified body, its Director and the personnel conducting the rest or check tests of the components of the structure must be the recreational craft or components of the design engineer, manufacturer, supplier, installer or their authorised representatives. They may not be directly or as authorized representatives involved in this product design, manufacture, marketing or maintenance.

147.146 those rules the conditions referred to in paragraph shall not preclude the possibility of exchanges of technical information between the manufacturer and the notified body.
148. The notified body shall have at its disposal the necessary human resources, financial resources and equipment, in order to be able to efficiently perform examination with the technical and administrative tasks.
149. the institution is registered in the commercial register of the Republic of Latvia.
150. the staff responsible for inspection shall comply with the following requirements: 150.1. appropriate technical and vocational education and training;
150.2. knowledge of the tests to be carried out and the test-taking experience;
150.3. skill to design certificates, notes and reports, which are required to verify the tests.
151. the institution guarantees the impartiality of inspection staff. Staff remuneration does not depend on the number of tests or test results.
152. the notified body shall take out liability.
153. the staff of the notified bodies shall be obliged not to disclose the resultant professional activities of commercial information.
11.154. Market surveillance market surveillance authority under the national budget resources to fulfil consumer centres. Consumer rights protection Centre carries out the laws and measures to prevent the provision of inadequate recreational vessels and their equipment distribution market.
155. If recreational vessels and their equipment, the manufacturer or his authorized representative in Latvia has not fulfilled the requirements laid down in these provisions, the trade of the product concerned is not permissible.
12. concluding issues 156. Recreational vessels are not equipped with the provisions referred to in paragraph 49 of the port reception facilities completely emptied the toilet contents collection system must be fitted with the system until 1 January 2005.
157. The entry into force of the provisions of a special cabinet rules.
Informative reference to European Union directive rules included provisions arising from Directive 94/25/EC.
Prime Minister e. Repše traffic Minister r. tit annex Cabinet 1 April 2003 regulations No 144 1. CE marking the CE marking consists of the following forms of uppercase letters ' CE '.

2. If the CE marking is reduced or enlarged the size, proportions in the sample.
3. The CE marking supplemented by the notified body identification number if it participates in the control of the construction, as well as with the last two digits of the year when the CE marking affixed.
4. The two components of the CE marking is the same vertical dimensions, which may not be less than 5 millimeters.
Traffic Minister r. tit