Cabinet of Ministers Regulations No 595 in Riga on 13 July 2004 (pr. No 42 28) New vehicle design normatīvtehnisk documentation and international manufacturer identification code assignment order Issued pursuant to the Highway Traffic Act article 15 the second part i. General questions 1. determines the new mopeds, motorcycles, tricycles, quads, cars, buses, trucks and trailers and semi-trailers these vehicles (hereinafter vehicle) normatīvtehnisk of the design documentation and international manufacturer identification code assignment. 2. the rules apply to commercial companies (companies) that are produced or manufactured for vehicles yet (hereinafter manufacturer), regardless of the State of completion of the vehicle manufactured (in one or more stages). 3. normatīvtehnisk of the harmonised vehicle design documentation and manufacturer assigned international manufacturer identification code gives the right to produce the vehicles. For vehicle manufactured could be used in road traffic, the manufacturer shall assess the conformity of the vehicle in accordance with the laws and regulations on the wheels of vehicles and their components conformity assessment. II. the structures of vehicles Built in dossier normatīvtehnisk 4. coordination arrangements to match new vehicle design documentation, manufacturer normatīvtehnisk road traffic safety Directorate (CSDD) submitted in: 4.1 submission;
4.2. preparation of the vehicle technical regulations, including the following information: 4.2.1 the "Introduction" section indicates the purpose of the construction of the vehicle and the planned production volume;
4.2.2. the section ' technical description of the manufacturing process "includes the main technological process of manufacture of the vehicle to be used on the same or other manufacturers made their system, Assembly units and a description of the node and process sequence;
4.2.3. the section ' technical description of the vehicle type "include information under this provision of the annex;
4.2.4. in "Constructive" include: 4.2.4.1. the vehicle dimensions, drawings;
4.2.4.2. Assembly drawings of the vehicle;
4.2.4.3. a main Assembly, Assembly units and assembly drawings;
4.2.4.4. the principle flowchart (for instance, electric, pneumatic, hydraulic);
4.2.4.5. the drawing specifications;
4.2.5. in section "calculation" indicates the vehicle's main constructive solutions, implements, node, system and Assembly unit strength calculations (bend, bend and cirp);
4.2.6. section "making rules" made each vehicle inspection procedures and conditions;
4.2.7. section "control methods" indicates under "technical description of the manufacturing process" and "technical description of the vehicle type" parameter, the size, characteristics and control methods of the rules and control instrumentation;
4.2.8. the section "operating rules" specifies the operating conditions of the vehicle maintenance recurrence and operating materials;
4.2.9 the section "labelling" includes: 4.2.9.1. the vehicle manufacturer's plate and vehicle identification number of symbols used in the samples;
4.2.9.2. vehicle identification number of the sample;
4.2.9.3. the vehicle manufacturer's plate (with the information) and the planned vehicle identification number location drawings;
4.2.9.4. the vehicle identification number in the letter and number combination explanation;
4.2.10. the section "manufacturer's warranty" includes manufacturer's warranty conditions. 5. the CSDD register of vehicles submitted by technical rules of manufacture and not later than 30 days, shall take a decision on whether the manufacturer is entitled to launch an experimental sample preparation according to the technical provisions. 6. In evaluating the vehicle manufacturing technical rules, make sure that the CSDD design technical solutions of the vehicle complies with the provisions of road traffic and the technical condition of the vehicle regulatory requirements and the laws or the manufacturer can ensure compliance with the production process of manufacturing the vehicle submitted CSDD technical rules and processes of the existing vehicle of effective control. 7. Experimental production of the samples is not allowed if the vehicle manufacture technical regulations have been developed in incomplete or new vehicle design technical solution does not meet the rules of the road or vehicle technical condition of regulatory legislation, the manufacturer cannot guarantee compliance with the production process of manufacturing the vehicle submitted CSDD technical rules and processes of the existing vehicle of effective control. 8. After the pilot of the vehicle type, the manufacturer of the sample tested for the relevant category of vehicle technical inspection stations and received an opinion on the conformity with the technical rules of manufacture of the vehicle. The opinion shall be submitted to the CSDD. Checking the experimental sample of a type of vehicle, the following procedures are carried out: 8.1. vehicle structure in conformity assessment in accordance with the approved vehicle manufacturing requirements of technical regulations;
8.2. the vehicle Assembly quality control;
8.3. the vehicle wiring mounting security control;
8.4. vehicle control, external projections, in order to determine whether the structure has no sharp corners, edges or other dangerous elements that may endanger the safety and health of people;
5.3. vehicle controls control according to the ergonomic requirements of the rules;
8.6. in the course of the examination of the vehicle. 9. If the vehicle made an experimental sample examination shows deviations from the vehicle manufacturing CSDD technical rules or other defects, the manufacturer to produce the vehicle prevents experimental samples check and received the opinion submitted CSDD. 10. After this rule 8 or 9 in the opinion referred to in paragraph CSDD within 10 working days of receipt of the decision on the construction of vehicles harmonisation of the documentation normatīvtehnisk. 11. After vehicle design documentation of the normatīvtehnisk reconciliation CSDD periodically controls the manufacturer's production system and quality assurance checks and manufacturing process produced vehicles in conformity with harmonized vehicle manufacturing documentation requirements. CSDD using random selection method, select the samples conformity with harmonized vehicle manufacturing documentation requirements checked the manufacturer's business or technical inspection station. 12. If the CSDD finds made vehicle normatīvtehnisk vehicle design documentation requirements, then depending on the nature of non-compliance, it shall take one of the following: 12.1 the manufacturer be expressed orally or in writing and shall specify the point in time of the reprimand, to which this inconsistency be removed;
12.2. declare invalid the individual vehicles manufactured until the manufacturer demonstrates the conformity of vehicles with the agreed structure of the vehicle in normatīvtehnisk documentation requirements;
12.3. recognized as appropriate to all vehicles manufactured until the manufacturer demonstrates the conformity of vehicles with the agreed structure of the vehicle in normatīvtehnisk documentation requirements;
12.4. invalidate the CSDD agreed the structure of the vehicle documentation to normatīvtehnisk non-compliance;

12.5. revoke the CSDD harmonised vehicle structure in normatīvtehnisk documentation. III. international manufacturer identification code and procedure 13. international manufacturer identification code (hereinafter referred to as the WMI code) consists of three symbols. This code is given to identify the vehicle manufacturer, and along with the vehicle identification number of the parts that ensure each vehicle's individuality. 14. the first WMI code symbol determines the geographic area of the country. Latvia made for marking on the vehicle the WMI code symbol used the letter "S". 15. The WMI code the second symbol in a geographical area. Latvia made for marking on the vehicle the WMI code the second symbol used by the numbers "1", "2", "3" or "4". 16. The WMI code the third symbol determined by the manufacturer in the country concerned. About WMI code the third symbol uses only Latin letters from "A" to "Z", except "I", "O" and "Q", or "1" digits to "9". 17. All manufacturers who made less than 500 per year vehicles about WMI code the third symbol always used the number "9". Assigned to the first, second, and third symbols clearly identify the manufacturer, the manufacturer shall also assign three CSDD symbol identification code, which is an integral part of the WMI code and included by the manufacturer for each vehicle identification number. 18. The WMI code in the second and third symbols, as well as WMI code in General for each vehicle manufacturer allocated CSDD. 19. After new vehicle design normatīvtehnisk reconciliation of the documentation not later than 10 working days CSDD time give the manufacturer the WMI code and inform the manufacturer. 20. After receipt of the WMI code manufacturer, concluding an appropriate agreement with the CSDD, is entitled to a trial of an experimental vehicle plate specimen to perform its tests and conformity assessment of the type of vehicle. IV. Decisions and appeals procedures for appeals 21. Decision on the structure of the vehicle normatīvtehnisk harmonization of the documentation of refusal or revocation in writing, stating the CSDD refusal or cancellation and specifies the order in which decisions may be challenged or appealed. 22. the manufacturer or his representative may challenge the CSDD or appeal to the law on administrative proceedings. Informative reference to European Union directive rules included provisions deriving from Council of 18 December 1975 Directive 76/114/EC, which provides for a uniform Community labelling of vehicles and identification procedures. Prime Minister i. Emsis traffic acting Ministers: Deputy Prime Minister a. Shlesers attachment Cabinet on 13 July 2004, regulations no 595 vehicle type information to be included in the technical description 1. Passenger car, bus, truck, trailer (semi-trailer) type of technical description general description 1.1 no PO box type approval code database name 1 0 General information 0.1. Make (name of manufacturer) 0.2. Type 0.2.1. Trade name (s) (if applicable) 0.3. means of identification of the type (if located on the vehicle) (a) 0.3.1. location of that designation 0.4. category (b) 0.5. name and address of the manufacturer, 0.8. Assembly plant address (if applicable) 1 2 General data and design characteristics 1.1. vehicle prototype photos or drawings of 1.3. number of axles and wheels of the steered axle 1.3.2. number and arrangement of 1.3.3. Powered axles (number, position, interconnection), 1.6 engine, location and position control half the 1.8-left/right (1) 1.9. Vehicle is equipped for driving on the right/left (1) side 3.

2. Masses and dimensions (c) (in kg and mm) 2.1. Wheelbase (s) (with the full mass) (d) 2.3.1. track of the steered axle (s) (e) 2.3.2. track of the other axle (s) (e) 2.4. vehicle dimensions 2.4.2. Chassis with bodywork 2.4.2.1. Length (f) 2.4.2.2. width (g) 2.4.2.3. height (unloaded condition) (h) (a-arm with adjustable height to specify the height of normal operation) 2.6. mass of the Vehicle (the minimum and maximum for each variant or version (the only passenger car)), together with bodywork, and with coupling device If it's a tractor, or mass of the chassis with cab if the manufacturer does not set up the bodywork and/or coupling device (including coolant, oils, fuel, 100% other liquids except used waters, tools, spare wheel and driver; the bus – the mass of the crew member (75 kg) if the vehicle is a dedicated seat) (i) breakdown of 2.6.1. Unladen mass (if it is a semi-trailer or centre-axle trailer-also, load on the coupling point) specified by the manufacturer 2.7. complete minimum mass of the vehicle (only for complete vehicles) specified by the manufacturer 2.8 full mass (maximum and minimum for each variant or version (only cars)) (j) 2.8.1. distribution of Mass among the axles, but in the case of semi-trailers or trailers with centre-axle trailer, load on the coupling point (maximum of each version and minimum) 2.9. Technically permissible maximum mass among the axles 2.11. technically permissible mass of the towed vehicle 2.11.1.2.11.2. Semi-trailer trailer (n) 2.11.3. Centre-axle trailer 2.11.4. Technically permissible maximum mass of the road train trailer without brakes 2.11.6. maximum mass of 2.12. Technically permissible maximum static vertical load/mass on the vehicle the coupling point 2.12.1. Technically permissible maximum static vertical load/mass on the coupling device of the motor vehicle are 4.3 (k) 3.1 Engine manufacturer 3.1.1. Manufacturer's engine code (according to the marking on the motor) 3.2. Internal combustion engine 3.2.1.1. working principle-spark ignition/compression ignition, four stroke/two stroke (1) 3.2.1.2. Number and arrangement of cylinders 3.2.1.3. Cylinder capacity (L) ... cm ³ 3.2.1.8. the manufacturer's specified maximum net power (m) … kW with ... min-1 3.2.1.10. the manufacturer's specified maximum useful torque (m) (n) ... NM to ... min-1 3.2.2. Fuel-diesel oil/petrol/LPG/any other fuel (1) 3.2.2.1. With exploratory method defined for leaded petrol Ron 3.2.2.2. With exploratory method defined for unleaded petrol Ron 3.2.3.1.1. number of fuel tanks and litres (n) 3.2.4. fuel feed: 3.2.4.1. By carburettor (s) Yes/No (1) 3.2.4.2. Fuel Injection (only with compression ignition) Yes/No (1) 3.2.4.2. Operating principle-direct injection/priekškamer/virpuļkamer (1) Inject fuel 3.2.4.3. (positive ignition only) Yes/No (1) 3.2.7. Cooling system-liquid/air (1)

3.2.8. Intake system-Turbo is/is not (1) 3.2.9.5. Exhaust system the output image location (excluding passenger cars and trailers (semi-trailers)) (n) 3.2.12. Environmental pollution reduction measures 3.2.12.2. Additional devices environmental pollution abatement (if there is, but not described in another section) 3.2.12.2.1. Catalytic exhaust converter is/is not (1). 3.2.12.2.2 oxygen probe is/is not (1) 3.2.12.2.3. air in addition to the supply is/is not (1). 3.2.12.2.4 exhaust gas recirculation is/is not (1) 3.2.12.2.5. Vapours emission control system is/is not (1) 3.2.12.2.6. Particulate trap is/ 3.2.12.2.7. (1) no other systems (description and operation) 3.2.13. location of the absorption coefficient (compression ignition engines only) 3.3. Electric Motor 3.3.1. Type (winding, excitation) 3.3.1.1. Maximum hourly output … kW 3.3.1.2. Operating voltage ….. V 3.3.2. Battery location 5 3.3.2.4.4. Transmission (o) 4.2 type (for example, mechanical, hydraulic, electrical) transmission 4.5 4.5.1. Type-with a manual/automatic/variator (1) 4.6. Gear ratios gear values transmission main transmission Variator maximum (1) 1.2.3., etc. Minimum Variator (1) reverse 4.7. vehicle maximum design speed (km/h) (w) 6 6. Suspension of each axle suspension 6.2. type and design of the 6.2.1. Height exaggerated yes/no/optional (1) 6.6.1. Tyre/drive combination (s) (for tyres indicate size designation, minimum load index, speed category symbol and wheel rim size) 6.6.1.1. Axis: 6.6.1.1.1.1.6.6.1.1.2.2. axis axis etc.

6.6.1.2. Spare wheel (if any) 7.7. Steering equipment 7.2. Mechanism and control 7.2.1 7.2.2 the mechanism type connected to the wheels (principled scheme, images or detailed description) 7.2.3. Amplification method (if any) 8.8.5. Antilock brake system (ABS) Yes/no/optional (1) 8.9. brief description of the braking device: a service brake (s) parking brake emergency brake (s) (s) (s) auxiliary (such as transmission brake , engine brake) wheel brake mechanism brake mechanism bows/pads (1) contains/does not contain (1) asbestos materials (specify the axles, if different) (n) 9 body 9 9.1. Type of bodywork (according to the national standard LVS 87 "vehicle types and their definitions" requirements) 9.3.1. number and arrangement of Doors 9.10. Interior fittings 9.10.3. Seats number 9.10.3.2.9.10.3.1.

Position and arrangement of 9.10.3.2.1. Seating position (s) that is not intended for use while driving 9.10.4.1. Type of head restraints: integrated/removable/separate (1) 9.12.2. additional safety equipment (specify: yes/no/optional) (L = left, R = right side, C = Centre) front air bag side air bag belt tensioning device the first row of seats L C R second row of seats L C R table can be extended If the vehicle has more than two rows of seats or if the width of the vehicle is located more than three seats 10.11. Towing vehicles and their trailers (semi-trailers) coupling device installed or installable 11.1 coupling device class and type 11.3. Instructions or principled scheme for mounting the coupling device on the vehicle and the strengthening of the manufacturer specified point photos or drawings, as well as additional information, if the use of the coupling type to the vehicle specific mount variants or versions 11.4. information on special towing brackets or mounting plates reinforcement 11.13.
Information that applies only to vehicles of categories M2 and M3 (n) 13.1. Bus class 13.2. number of 13.3. Parking of passenger and crew seats 13.3.1. Crew seats is/is not (1) 13.4. passenger embarkation and disembarkation used for door number 13.5. number of emergency exits (doors, Windows, hatches) 13.6. volume of luggage compartment ... m3 8.5. Baggage for the roof area ... m2. Devices intended for ease of picking up (lift or an inclined platform support system) of the vehicle type version 1.2 and version identification of the manufacturer in table 12 indicates this sub-chapter annex 1.1. differences in the parameters for each type of variant and version. Vehicle type, variant and version type definitions given in regulations for wheeled vehicles and their components conformity assessment. These differences at the beginning of the sign to be in uppercase letters of the alphabet so that you can clearly see that differences attributable to each type, variant and version. 13. vehicle type concerned for each version a separate table to fill. If all versions of the type variant are the same, the data in the column "version number" indicates the word "All". Table item number All version 1 version 2 etc.
Version number 14. These data the manufacturer may be filed in any other form or arrangement, if the required information and its transparency. 15. In all cases, be included in all versions of the vehicle type and version of the possible combinations. 16. each type of option, and each version is identified by a letter and number combination. The notes. (1) Delete where inapplicable. (a) If the identification of the vehicle type designation consists of the symbol that does not apply to the type of vehicle or component identification under this technical description, these terms are to be replaced by the symbol '? ' (e.g. ABC?? 123??). (b) according to the normative acts of the State of the vehicle the technical inspection classification specified. (c) if there is a version with a normal cab and cab with bunk, in both cases, indicate the mass and size. (d) ISO Standard 612-1978 6.4. requirements of paragraph. (e) according to ISO Standard 612-1978, the requirements of paragraph 6.5. (f) ISO Standard 612-1978, the requirements of paragraph 6.1, but buses, trucks and trailers (semi-trailers) – under the European Union Directive 97/27/EC annex I, section 2.4.1. (g) ISO Standard 612-1978, the requirements of point 6.2, but buses, trucks and trailers (semi-trailers)-according to Directive 97/27/EC annex I, section 2.4.2. (h) ISO Standard 612-1978, the requirements of paragraph 6.3, but buses, trucks and trailers (semi-trailers)-according to Directive 97/27/EC annex I, section 2.4.3. (i) assumes that the driver's mass is 75 kg (according to ISO standard 2416-1992); fuel tanks must be filled about 90% of the capacity stated by the manufacturer. (j) in the case of semi-trailers and lorries tractors laden weight saddle consists of vehicle mass and load on saddle device. (k) On non-traditional types of engines and components submit data that is equivalent to the following. (L) The value shall be calculated on the assumption that π = 3.1416 and rounded to whole number (cm ³). (m) based on the European Union Directive 80/1269/EEC. (n) according to the European Union annex I of Directive 70/156/EEC, taking into account Directive 98/14/EC amendments made. (o) indicates data must be submitted for each option. (p) a 5% tolerance is Permitted. 2. Moped, motorcycle, tricycle and quadricycle technical description 2.1 General description no PO box type approval database code name 17.0. General information 0.1. make 0.2. Type (specify any variants and versions, identifying each with a number or letter combination) 0.3. means of identification of the type (if located on the vehicle) (a) 0.3.1. location of that designation 0.4. Category of vehicle (b) 0.5. Manufacturer's name and address of manufacturer's authorised representative 0.6. name and address of the 0.4. vehicle plates and place the reinforcement of 0.7.1.
Type the serial number starts with 0.8. Component type-approval mark the location and method of affixing 18.1. General design 1.1. vehicle prototype photos or drawings of the complete vehicle 1.2 exploded view drawing with overall dimensions of 1.3. number of axles and wheels 1.4. engine location and position 19. Weight (kg) 2 (c). the unladen mass of the vehicle 2.1 2.1.1. Unladen mass(es) among the axles of 2.2. mass of the vehicle with the driver 2.2.1. Distribution of this mass among the axles 2.3. Manufacturer's gross vehicle weight specified in 2.3.1. Distribution of this mass among the axles

2.3.2. Technically permissible maximum mass among the axles 2.4. maximum growth, which may initiate movement with the manufacturer's specified technical permissible maximum mass of 2.5. technically permissible mass of the towed vehicle 20.3. Engine (d) 3.0 3.1. the manufacturer Mark 3.1.1. Type 3.2. Spark ignition or compression ignition engine 3.2.1. Engine characteristics 3.2.1.1. Operating cycle-spark ignition/compression ignition, four/two stroke (1) 3.2.1.2. Cylinder number, position and sequence of operation 3.2.1.2.1. Cylinder internal diameter ... mm (e) 3.2.1.2.2. Stroke … mm (e) 3.2.1.3. Cylinder capacity ..... cm3 (f) 3.2.1.4. compression 3.2.1.5. ratio (2) cylinder head, piston, piston ring and cylinder 3.2.1.6. Idling speed drawing (2) … … min-1 3.2.1.7. Maximum net power … kW with ... min-1 3.2.1.8. maximum useful torque ... NM with … …. min-1 3.2.2. Type of fuel-diesel/petrol/mixture/LPG/other (1) 3.2.3. fuel tank 3.2.3.1. maximum capacity (2) 3.2.3.2. Drawing of the tank and the indication of the construction materials for the circuitry that 3.2.3.3. precise identification of the location of the tank on the vehicle 3.2.4. fuel feed 3.2.4.1. By carburettor Yes/No (1) 3.2.4.1.1. Mark 3.2.4.1.2.3.2.4.1.3. Number type 3.2.4.1.4. Regulation (2) 3.2.4.1.4.1.3.2.4.1.4.2. pludiņkamer units level 3.2.4.1.4.3. mass of Float in 3.2.4.1.4.4. Float needle (if not do not fill in this box) 3.2.4.1.4.5. Fuel curve that reflects the air flow and settings required to 3.2.4.1.5. Cold function for engine starting system-manual/automatic (1) 3.2.4.1.5.1. Operating principle (s) injecting fuel 3.2.4.2. (compression ignition engines only) Yes/No (1) 3.2.4.2.1. system description 3.2.4.2.2. Operating principle-direct/indirect injection/virpuļkamer (1) 3.2.4.2.3. injection pump 3.2.4.2.3.1. Mark 3.2.4.2.3.2. type (if not, do not fill in this field) 3.2.4.2.3.3. Maximum fuel delivery (1) (2) ... mm/stroke or cycle ³ If the pump rotational speed is … min-1 or 3.2.4.2.3.4. injection advance curve (2) 3.2.4.2.3.5. Injection advance curve (2) 3.2.4.2.3.6. Calibration procedure-bench/engine (1) 3.2.4.2.4. Speed regulator 3.2.4.2.4.1. Type 3.2.4.2.4.2. "said point laden mode 3.2.4.2.4.2.1. …. min-1 3.2.4.2.4.2.2. Unloaded mode ... min-1. Idle speed 3.2.4.2.4.3 ... min-1 3.2.4.2.5. injection piping length 3.2.4.2.5.1 … 3.2.4.2.5.2. Internal diameter: mm ... mm. Nozzles 3.2.4.2.6.1.3.2.4.2.6 Mark 3.2.4.2.6.2. type (if not , do not fill in this field) opening pressure 3.2.4.2.6.3. (2) … … kPa or characteristic curve 3.2.4.2.7. Cold (2) engine starting system 3.2.4.2.7.1. Mark 3.2.4.2.7.2. type (if not, do not fill in this field) 3.2.4.2.7.3. the description starting accessories 3.2.4.2.8.1 3.2.4.2.8.. Mark 3.2.4.2.8.2. type (if not, do not fill in this field) 3.2.4.2.8.3. system description 3.2.4.3. Fuel Injection (positive ignition only) Yes/No (1) 3.2.4.3.2 3.2.4.3.1. Description of the system.

Principle of operation the intake manifold (single/multiple point/direct injection/other (1)) 3.2.4.3.2.1. injection pump mark 3.2.4.3.2.2. type injection pump nozzle opening pressure 3.2.4.3.3. (2) … … … … … kPa or characteristic curve (2) 3.2.4.3.4. Injection advance 3.2.4.3.5. Cold engine starting system 3.2.4.3.5.1. Operating Principles 3.2.4.3.5.2. action/restrictions set (1) (2) 3.2.4.4. Fuel pump is/is not (1) 3.2.5. Electrical equipment 3.2.5.1. Rated voltage ..... V, positive/negative Earth (1) Earth 3.2.5.2. Generator 3.2.5.2.1. Type 3.2.5.2.2. Nominal capacity … W 3.2.6. Ignition 3.2.6.1. Mark 3.2.6.2. Type 3.2.6.3. working principle 3.2.6.4. Ignition advance curve or set point (2) 3.2.6.5. starting lead angle (2) … … … …. degrees before top Exchange point 3.2.6.6. Contact gap (2) … mm. Contact connected position 3.2.6.7 angle (2) … degrees 3.2.6.8. Interference cancelling system damping suppression devices 3.2.6.8.1. scheme and terminology 3.2.6.8.2. The indication of the nominal DC resistance and the nominal resistance ignition wires for the 3.2.6.8.3 Cooling System metres.-liquid/air (1) 3.2.7.1. the engine temperature control mechanism of a nominal setting 3.2.7.2. Liquid fluid 3.2.7.2.1. way 3.2.7.2.2. Circulating Pump is/is not (1) 3.2.7.3.3.2.7.3.1. Forced ventilation air is/is not (1) 3.2.8. Intake system 3.2.8.1. Pressure charger is/is not (1) 3.2.8.1.1. Mark 3.2.8.1.2. Type 3.2.8.1.3. Description of the system (e.g. maximum pressure turbocharger ... kPa and overpressure valve setting) 3.2.8.2. Intercooler is/is not (1) 3.2.8.3. Intake pipes and their fittings (for example, increased the pressure Chamber, heating device, additional air intakes) description and drawings 3.2.8.3.1. Intake Manifold description (drawings and/or photographs) 3.2.8.3.2. Air filter, drawings (if not do not fill in this box) 3.2.8.3.2.1. Mark 3.2.8.3.2.2. Type 3.2.8.3.3. Inlet muffler drawings (if not, do not fill in this field) 3.2.8.3.3.1. Mark 3.2.8.3.3.2. Type 3.2.9. exhaust system the exhaust system 3.2.9.1. Drawing 3.2.10. Intake and exhaust channel minimum cross section 3.2.11. Data on intake system or equivalent data 3.2.11.1. Maximum lift of valves, angles of opening and closing, or data on a different system setup values 3.2.11.2. valve heat setting ranges of the spaces (1) 3.2.12. measures against air pollution 3.2.12.1. device for recycling crankcase gases (only If there is a four-stroke engine). Description and drawings 3.2.12.2. Additional devices against the contamination of the environment (if there are and they are not described in another heading) 3.2.12.2.1. Description and/or drawings 3.2.13. Location of the absorption coefficient symbol (compression ignition engines only) 3.3. Electric Motor 3.3.1. Type (winding, excitation) 3.3.1.1. Maximum hourly output … kW 3.3.1.2. Operating voltage ….. V 3.3.2. Batteries 3.3.2.1. Number of items 3.3.2.2. Mass ... kg 3.3.2.3. Capacity ... Ah (ampere hours) 3.3.2.4. Position 3.4. Other engines or motors or combinations thereof (particulars regarding the parts of such engines) 3.5 the temperature specified by the manufacturer of the cooling system of the 3.5.1 3.5.1.1. Liquid cooling-the maximum temperature, rippling through the radiators ... ° C of cooling air 3.5.1.2.1 3.5.1.2. Milestone 3.5.1.2.2. maximum temperature at reference point ... ° C 3.6. Lubrication System 3.6.1. Description of the system oil reservoir 3.6.1.1. location 3.6.1.2. Feed System (for example, pump/injection into intake/with fuel) (1) 3.6.2. Oil mixed with fuel percentage 3.6.2.1.3.6.3. Oil cooler (radiator) is/is not (1) 3.6.3.1. Drawing (if not, do not fill in this field) 3.6.3.1.1. Mark 3.6.3.1.2.21.4. Transmission Type (g) 4.1. Drawing of the transmission (scheme) 4.2 type (for example, mechanical, hydraulic, electrical) 4.3. Clutch (type) 4.4 transmission 4.4.1. Type-automatic/manual (1) 4.4.2. Method of control-by hand/foot (1) 4.5. Gear ratios R1 R2 R3 N Rt: minimum 1 Variator. 2.3., etc. Variator maximum reverse gear ratio N = R1 = primary gear ratio (engine and gearbox primary shaft) R2 = secondary ratio ratio (transmission of primary and secondary shaft output shaft) R3 = main transmission gear ratio (transmission of the outgoing shaft and the driving wheel speed) Rt = overall transmission ratio 4.6 maximum Vehicle speed and gear design, which it achieved (in km/h) (h) 4.7. Speedometer odometer and is/is not (1) 4.7.1 4.7.2. Mark type 22.5-arm suspension drawing of 5.1 and 5.2.
Tyres (category, dimensions and maximum loading) and rims 5.2.1. Nominal rolling circumference is 5.2.2. the Manufacturer pressure … kPa 5.2.3. Tyre and disk combinations 23.6. Steering mechanism and leadership 6.1 6.1.1. type Mechanism 24.7. Braking equipment 7.1. diagram of the brake equipment 7.2. Front and rear brakes-disc and/or arc (1) 7.2.1 7.2.2. Type of Mark 7.3 braking component drawings 7.3.1. and/or Rim pads (1) contains/does not contain asbestos materials (1) 7.3.2. Linings and/or pads (1) content/content (not 1) asbestos materials 7.3.3. Rods and/or pedals (1) 7.3.4. Hydraulic reservoirs 7.4. Other devices-drawing and description 25.8. Lighting and light-signalling devices 8.1. list of all devices (including the number, make, model, component type-approval marks and numbers, high beam lamp light volume, colour kontrolskaitl, the corresponding control device) 8.2. Lighting and light-signalling device placement diagram 8.3. Emergency alarm lamp 8.4. Additional requirements for special vehicles 26.9. Equipment 9.1 9.1.1. Type of the coupling device-hook/eye/other (1) 9.1.2. Coupling device location and design of the illustrative photographs or drawings 9.2. Control devices, control devices and the location and identification of indicators 9.2.1. Symbol, control devices, control devices and light placement photos or drawings of the protective device 9.4 9.4.1 9.4.2. Types of devices devices used to describe 9.5. Audible warning device 9.5.1. Description of the device and used for the purpose 9.5.2. Mark 9.5.3. Type 9.5.4. name and address of the manufacturer, 9.5.5. Component type-approval mark 9.5.6. Audible warning device location and illustrative drawings in relation to vehicle body elements detailed building 9.5.7. a description of the method, indicating the part of the vehicle to which the audible warning device attached 9.6. rear registration plate location 9.6.1. Building a plane angle in relation to the vertical 2.2. additional technical description the moped and motorcycle 27.1. Equipment 1.1. Rear-view mirrors 1.1.1. Mark 1.1.2. Type approval mark 1.1.3 version 1.1.4. Rear-view mirror locations and illustrative drawings in relation to vehicle body components 1.1.5. detailed description of the method of strengthening indicating the part of the vehicle for which the rear-view mirror mounted 1.2. Stop 1.2.1. Type-Central/side (1), 1.2.2. Stop location and illustrative drawings in relation to vehicle body elements 1.3. strengthening elements of the side 1.3.1. Location and construction photographs or drawings of the passenger handle 1.4 1.4.1. Type-strap/handle (1) 1.4.2. Location photos or drawings 2.3. additional technical description the motorcycle with a sidecar, tricycle and quadricycle 28 Gauge 1 and mass (mm) (kg) and overall dimensions of 1.1. to be followed, equipping with 1.1.1. bodywork the chassis length 1.1.2. width 1.1.3. unladen height position 1.1.4. Front overhang 1.1.5. Rear overhang 1.1.6. limit of the Centre of gravity of the vehicle with bodywork 1.2. masses (c) for the 1.2.1. maximum capacity stated by the manufacturer. 2.29 equipment 2.1. Bodywork the bodywork type 2.1.1 2.1.2. overall dimensions of a drawing of the Interior with an exploded view drawing of 2.1.3 to 2.1.4. overall dimensions with construction materials and methods of manufacture 2.1.5. Passenger door it latches and hinges door layout, 2.1.6. overall dimensions, direction and maximum opening angle of opening 2.1.7. Drawing showing the latch and hinge locations on the door latch and hinge 2.1.8. technical description 2.2. Windscreens and other glass 2.2.1. Windscreen 2.2.1.1. materials 2.2.2. Other window 2.2.2.1. materials 2.3. windscreen wipers 2.3.1. Detailed technical description (including photographs or drawings) 2.4. windscreen washer 2.4.1. Detailed technical description (including photographs or drawings) 2.5. Defrosting and demisting systems equipment 2.5.1. Detailed technical description (with photographs or drawings) 2.6. Rear-view mirrors 2.6.1. Mark 2.6.2. The type approval marking version 2.6.3 2.6.4. Rear-view mirror locations and illustrative drawings in relation to vehicle body elements 2.6.5.

A detailed description of the method of strengthening, indicating the part of the vehicle for which the rear-view mirror mounted 2.7 2.7.1. Number of Seats 2.7.2. Arrangement of "R" point 2.7.3. coordinates or drawing (s) of the driver's seat 2.7.3.1.2.7.3.2. other seats 2.7.4. expected tilt of the seat backs 2.7.4.1. driving seat 2.7.4.2. other seats 2.7.5. Seat adjustment range 2.7.5.1. driving seat 2.7.5.2. other seats 2.8. Passenger compartment heating system 2.8.1. Heating systems General description, if it uses engine coolant 2.8.2. Heating systems General description If it uses the cooling air or exhaust gas, including: 2.8.2.1. dimensioned drawing of heating systems, illustrating its position in the vehicle and silencing the arrangement (including the heat exchange points) 2.8.2.2. exhaust gas heat heating systems using the radiator exploded view drawing or an exploded view drawing of the device in which the heat exchanger, (if the heating system uses the engine cooling air) 2.8.2.3. a heating radiator or cross section drawings of the device, in which the heat of the showing wall thickness, as well as the materials used and their surface properties of other key 2.8.2.4. heater element (such as a fan) method of manufacture specifications and technical indicators installed belt 2.9.1. number and position of that reference to the seats where that type of belt can be installed in the D/P * full component type-approval mark Variant, if applicable front seating positions in the rear seats, the remaining seats special devices (example: , seat height adjustment, the inertia of the machine) * D = driver's side; P = front passenger side 2.10. Safety belt anchorages 2.10.1. number of Anchorages and the location of the photos or the superstructure 2.10.2. drawings, illustration and "R" point location and size 2.10.3. Seat belt anchorages and parts of the drawings (including the materials) 2.10.4. list of a type of safety-belt, which allowed for installation in a vehicle seating positions and Strengthening the place of fastening the vehicle seating position in the front seats to the right side of the bottom edge of the inner attachment of the upper anchorage average seating capacity of the lower edge of the inner attachment of the upper anchorage of seats on the left side of the lower anchorage
the inner edge of the upper anchorage back right side seats lower mounting the inner edge of the upper anchorage average seating capacity of the lower edge of the inner attachment of the upper anchorage of seats on the left side of the lower edge of the inner attachment of the upper anchorage legend: (A): the three-point belt; (B): the waist belt; S: a special type of belt-in this case provide specific information about these types, column "comments"; With, or Sr: belt with inertia reel; With, BRE and SRE: belt with inertia reel and an energy absorber at least at one of the notes. (1) Delete where inapplicable. (2) specify the tolerance (s). (a) If the identification of the vehicle type designation consists of the symbol that does not apply to the type of vehicle or component identification under this technical description, these terms are to be replaced by the symbol '? ' (e.g. ABC?? 123??). (b) according to the normative acts of the State of the vehicle the technical inspection classification specified. (c) 1. the mass of the completed vehicle-operation prepared transport mass with the following equipment: 1. accessories, ensuring the vehicle is in motion; 1.2. the complete electrical equipment, including the manufacturer, the installed lighting and light-signalling devices; 1.3. instruments and accessories; 1.4. operating liquids in quantities required for all vehicle functions (fuel and the fuel/oil mixture are not included in the mass, but include battery acid, cooling liquid, as well as the engine and hydraulic oil mass). 2. Mass-mass of the completed vehicle, plus: 2.1. mass of fuel (fuel must be filled to 90% of the capacity stated by the manufacturer); 2.2. Optional mass that does not include the mass of the completed vehicle (such as a tool kit, trunk, front windscreen, protective equipment). 3. Technically permissible maximum mass stated by the manufacturer-mass with a technical permissible vehicle operation. 4. maximum capacity – mass obtained from the technically permissible maximum mass less the tare weight and driver (75 kg). (d) On non-traditional types of engines and components submit data that is equivalent to the following. (e) the number you want to round to the nearest tenth of a millimetre. (f) this value calculated on the assumption that π = 3.1416 and rounded to whole number (cm ³). (g) the information to be submitted for each option. (h) a 5% tolerance is Permitted. (i) ' R ' point "or" seating reference point ".
Traffic acting Minister — Deputy Prime Minister a. shlesers