Cabinet of Ministers Regulations No 647 in 2005 (30 august. 49.3 §) rules on recreational craft construction, assessment of conformity and placing on the market are Issued in accordance with the law "on conformity assessment" article 7 of the first and the second part 1. General questions 1. determines the rest of the vessel design and construction safety requirements applicable to the offering on the market, as well as the rest of the vessel conformity assessment procedures. 2. The terms used in the following terms: combination of UR2.1.atp vessel — any type of sport or leisure for vessel hull length from 2.5 to 24 m, measured according to the applicable standards. Requirements of this Regulation apply to the shipping agent, which prompted the European Union market as a recreational vessel, even if used for chartering or training;
2.2. water bikes — the vessel with a length of less than 4 metres, which is the internal combustion engine and water pump and the thrower that person (people) runs, sitting, standing or kneeling on, rather than it being in the inside of the hull;
2.3. engine: any internal combustion engine with spark or compression ignition vessels progress (two-stroke and four-stroke engines, built-in engines with Z-shaped propeller drive and single exhaust system, as well as the uzkaram engine);
2.4. the manufacturer: any natural or legal person who designs and manufactures vessels covered by this regulation, or has such a product designed and/or manufactured product, intended for placing on the market on his own behalf;
2.5. the authorized representative in the European Union, any natural or legal persons established in, which has received a written mandate from the manufacturer to act on their behalf. 3. the rules apply to vessels and structures, as well as on the engine exhaust and noise emissions and apply: 3.1. recreational craft and partly completed boats;
3.2. water motorcycles;
3.3. the rules referred to in point 7 of the recreational craft components, if they are offered on the market of the European Union and is intended for installation. 4. the provisions referred to in paragraph 3, the products rules apply only for the first time offering them on the market or put into service in use. 5. The rules referred to in paragraph 3 of the products conform to the safety, health, environmental protection and consumer protection requirements set out in section 2 of these regulations. 6. the provisions do not apply: 6.1., to the following vessels projects and structures: 6.1.1. vessels designed solely for racing, including rowing racing boats and training rowing boats, which the manufacturer is labelled accordingly;
6.1.2. canoeing, smailīt, gondola and water bikes;
6.1.3. sailing surfboards;
6.1.4. surfing boards, including boards, with drive;
6.1.5. the original historical craft and individual replicas designed and built before 1950 are mostly from the original materials and labelled as a producer;
6.1.6. experimental vessels, if they are not offered in later European Union market;
6.1.7. the vessels built for personal use, if for the next five years they will not be offered in the market of the European Union;
6.1.8. the vessels, which provide with the crew to perform the carriage of passengers;
6.1.9. underwater vessels;
6.1.10. the vessels to the air bag;
6.1.11. vessels with hydrofoils;
6.1.12. vessels whose engine uses steam energy plant by burning coal, coke, wood, oil or gas;
6.2. the following engine exhaust emissions: 6.2.1 propulsion engines installed or intended for installation: 6.2.1.1. shipping products intended exclusively for competition and which manufacturer is labelled accordingly;
6.2.1.2. pilot shipping when they later will not be at all in the European Union market;
6.2.1.3. the shipping products, with the crew for the commercial carriage of passengers;
6.2.1.4. submarine navigation products;
6.2.1.5. shipping products on air cushions;
6.2.1.6. shipping products with low water wings;
6.2.2. the original historical engines and their individual copies, of which the project was designed before 1950 and which were not produced in series and set this rule and 6.1.5.6.1.7. shipping referred to in media;
6.2.3. engines built for personal use if they are within five years (from commissioning) will not be offered in the market of the European Union;
6.3. the noise emissions: 6.3.1. all vessels referred to in paragraph 6.2. of these rules;
6.3.2. the vessels built for personal use if they are within five years (from commissioning) will not be offered to the European Union market. 7. Recreational craft design components are the following: 7.1 all the equipment built pretaizdegšan engines, engines with Z-shaped propeller drive and the uzkaram engines;
7.2. protectors against starting the engine the engine of all uzkaram;
7.3. Steering, steering mechanisms and cable assemblies;
7.4. fuel tanks intended for fixed Assembly and fuel hoses;
7.5. manufactured hatches and scuttles. 8. recommends that the Ministry of transport to society with limited liability "standard" European Union reliance standard. 9. Limited liability company "Latvian standards" submit for publication in the newspaper "journal" the Latvian National Standard, a list of applicable requirements of these regulations (hereinafter referred to as the applicable standards). 2. the rest of the vessel design and construction safety requirements 10. Depending on the design of the rest of the ships are divided into four categories: category A 10.1 "Ocean" — designed for long journeys where conditions may exceed wind force 8 (Beaufort scale) and wave height: 4 metres, except in exceptional circumstances;
10.2. Category B "open sea" – designed for offshore voyages where conditions up to wind force 8 ball (inclusive) and the wave height — up to 4metr (inclusive);
10.3. C category "coast" — designed for voyages in coastal waters, large bays, river sources, lakes and rivers, where conditions and wind strength is up to 6ball (inclusive) and the wave height up to 2 metres (inclusive);

10.4. Category D "Protected waters"-designed journeys protected coastal waters, small bays, small lakes, rivers, and canals where conditions up to wind force 4 Ballroom (inclusive) and the wave height 0.3-meters (inclusive), but separate waves-0.5 metres (inclusive), for example, from a passing ship. 11. The category of recreational vessels designed and built in such a way that they comply with the rules laid down in paragraph 10 the category criteria for stability, buoyancy, and other requirements laid down in this chapter and to have good handling characteristics. 12. the rest of the hull in put: 12.1. recreational craft identification number according to the standards applicable to the following: 12.1.1. manufacturer's code;
12.1.2. country of production;
12.1.3. serial number;
12.1.4. year of construction;
12.1.5. the model year;
12.2. manufacturer's plate with the following information: 12.2.1. name of manufacturer;
12.2.2. the CE marking (annex 1) according to this provision the provisions of Chapter 9;
12.2.3. the category according to the rules laid down in point 10;
12.2.4. maximum load capacity stated by the manufacturer pursuant to paragraph 22 of these rules, except the built-in tank content when they are full;
12.2.5. the number of persons stated by the manufacturer, the carriage of which the ship is intended. 13. Depending on the category of the recreational craft shall be so constructed as to reduce the risk of falling overboard and facilitate boarding the ship. 14. A Person who runs a recreational vessel from the ship's main control site under normal conditions (taking into account the speed and load) will ensure a good visibility in all directions. 15. To the rest of the ship owner's manual located in one of the languages of the European Union or its Member States in a specific language, in which the engine is offered in the market. In this guide, in particular the risk of fire and flooding, the unladen ship weight in kilograms and include the information referred to in paragraph 12.2 of these provisions, in point 22 and 26. 16. Recreational craft material choice and design provides the connectivity to the rest of the ship would be strong enough and matched it to the category in accordance with paragraph 10 of these regulations and the recommended maximum load capacity builder in accordance with the provisions of point 22. 17. Recreational craft, on account of its category in accordance with paragraph 10 of these regulations and the design maximum capacity in accordance with paragraph 22 of these rules is sufficient stability and freeboard height. 18. Building the rest of the body, ensure that the vessel would have the buoyancy characteristics appropriate to its category in accordance with paragraph 10 of these regulations and the design maximum carrying capacity in accordance with paragraph 22 of these regulations. 19. Apdzīvojamo daudzkorpus rest of the vessels built in such a way as to ensure buoyancy also overturned intact above the water. Recreational vessels the length of which does not exceed six metres and which can quickly fills with water, provided with buoyancy. 20. open the rest of the hull, deck and superstructure must not affect the integrity of the watertight integrity of the constructive or integrity of these openings close. Windows, Windows, doors and hatch covers to withstand the water pressure, which is possible, given their location, as well as pressure from the weight of people moving on deck. Openings in the hull, allowing water into the casing and scattering from it and below the waterline (which corresponds to the recommended maximum load capacity builder in accordance with this provision, paragraph 22), it is equipped with an easily accessible means of closing. 21. Recreational vessel designed and built in such a way as to minimize the risk of sinking, paying special attention to: 21.1. kokpit and other Board recesses, which must be pašdrenējoš or protected by other means, to hold water from entering inside;
21.2. the ventilation equipment;
21.3. the water evacuation capabilities using pumps or other means. 22. the maximum load capacity of the design (including fuel, water, food, miscellaneous equipment and people (in kilograms)), a recreational craft is designed, based on the category in accordance with the provisions of paragraph 10, stability and freeboard height in accordance with the provisions of paragraph 17 and buoyancy in accordance with the provisions of paragraph 18. 23. All category A and B, as well as C and D category, which is more than six metres, shall be equipped with one or more easily accessible to the liferafts. Raft size corresponds to a number of people, one vessel can carry according to its design and the manufacturer's recommendations. 24. Apdzīvojamo daudzkorpus rest of the vessels that are longer than the 12metr, equipped with rescue facilities to the roll of the ship or fire. 25. the rest of the ship, given the category and characteristics, shall be fitted with one or more ropes, or strengthening other means that could safely withstand the appropriate anchor, tethering and towage. 26. the manufacturer shall ensure that the driving characteristics of the ship would be satisfactory, with the most powerful engine to which the rest of the ship is designed and built. Recreational craft engine maximum power indicates the owner's manual under applicable standards. 27. The built-in engines placed on a partition that is separate from the living quarters to reduce the fire or fire spread risk, as well as to reduce the danger of living places, caused by toxic smoke, heat, noise and vibration. 28. the details of the engine and ancillaries required often to check and serve, is readily available. 29. the insulating materials inside engine compartment must not be flammable. 30. The engine compartment is ventilated and prevent water from entering through the compartment openings. 31. Open engine hot or moving parts that can injure people, effectively covers, unless the engine is protected by a shell, or shell. 32. Recreational craft, which is uzkaram engine, you need a device to prevent starting the engine when the gearbox is in neutral position, except in the following cases: 32.1. engine generates static driving force of less than 500 newtons (N);

32.2. the engine is equipped with a throttle opening limiting device for starting the engine at the moment does not allow static driving force of more than 500 n. 33. Water motorcycles made for automatic engine stopping device, or a device that automatically reduces the speed of the circulation and movement forward, if the driver discount corner or actually go overboard. 34. The filling, storage, ventilation and feeding equipment designed and installed so as to minimize the risk of fire and explosion. Fuel tanks, pipes and hoses are separated or protected from any significant source of heat. Tank fabrication materials and their design meets the capacity and fuel type. All compartments are ventilated containers. 35. Petrol stores tanks which do not form part of the ship's hull and are: 21.8. separated from the engine compartment and from all other source of ignition;
35.2. separated from living quarters. 36. Diesel fuel can be stored in containers which are part of the hull. 37. The electrical system is designed and installed so as to ensure the proper operation of recreational vessel under normal conditions of use and to reduce the fire and electrical shock hazard. 38. The electrical system is designed and installed so as to ensure that all circuit protection against overload and short circuits, except engine starting circuits that use a battery. 39. The electrical system has ventilation to prevent the accumulation of gases that can be released from batteries. 40. The batteries are firmly secured and protected from water penetration. 41. the management system is designed, constructed and installed so as to ensure the management team putting the foreseeable operating conditions. 42. Sailing ships and recreation recreational vessels with one engine and built-in remote steering system equipped with driving the ship's emergency management means that ships could run at a reduced speed. 43. the gas system, intended for use on recreational craft, ensure steam drain. They are designed and installed so as to prevent spill and explosion risk and leakage testing is available. Gas system components and materials are suitable for gas and resistant to the marine environment caused by voltage and exposure. 44. each gas appliance is equipped with a pretuzliesmošan facility, which is valid for all types of burners. Any equipment that consumes gas, supplied by a separate branch of the distribution system, and concluded with a separate closing device. To prevent gas leaks and combustion products of injury, provide adequate ventilation. 45. vessels with permanently integrated gas system is fitted with a closed compartment to hold the gas cylinder. Partitions separated from living quarters, they are only available from the outside and ventilated to the outside so that the gas spilling out of the deck. Permanently integrated gas system after its installation. 46. choosing the type and layout of equipment on board, having regard to the risk of fire and its spread. Special focus on devices with an open flame (ensure that it is in close proximity to flammable objects), engines, auxiliary machinery and mechanism of the hot zones (not deploy the wiring over them) and unsettled oil and fuel pipes (prevents oil and fuel overflows). 47. Recreational craft shall be supplied with appropriate fire-fighting equipment as well as fire hazards under the fire-fighting equipment placement. The vessel is not put into service until the specific location is not placed in suitable fire-fighting equipment. Gasoline engine compartment shall be protected with fire-extinguishing system, which in case of fire allows you to delete the fire without opening the compartment. Portable fire extinguishers installed in easily accessible places, one of them is placed so that it can be easily to reach from the main control board. 48. The rest of the ship's navigation lights comply with the 1972 Convention on 20 October the international vessel collision prevention regulations (COLREG-72) or the European inland navigation code (CEVN). 49. Recreational craft is designed so as to prevent the release of contaminants (e.g., oil, fuel) accidental discharges outside the Board. 50. For recreational craft fitted with toilets, holding tanks are required or the possibility of such a tank set up. Holding tanks and drain hoses pipe diameter depending on the tank in accordance with the applicable standard is that tube withstand suction pressures. Any through the rest of the ship's hull drain valves that are applied to a safe conclusion. 51. every engine is clearly labeled with the following information: 51.1. manufacturer's trademark or trade name;
51.2. engine type and engine make (if necessary);
51.3. the unique engine identification number;
51.4. the CE marking, if defined in Chapter 9 of these regulations. 52. a mark under normal working conditions throughout the lifetime of the engine are: 52.1. durable, clearly legible and indelible. If marked on tags or plates, their attachment is rugged and tags/plates cannot be removed intact;
52.2. shielded from the moving parts of the engine;
52.3. positioned to be easily visible after the engine has been assembled with all the engine components needed for your work. 53. The engine shall be so designed, constructed and assembled so that after correct installation under normal working conditions the emissions do not exceed the allowable size (annex 2). 54. the engine manufacturer To prepare the necessary instructions and to add all new engines when they are first placed on the market before the endurance test (based on normal operating cycle of the engine) the engine manufacturer may obtain the relevant information to calculate engine fatigue. The manufacturer shall ensure that, following the instructions, the engine parameters over the duration of the match. 55. engine operation times: 55.1. the built-in engine or engine with Z-shaped propeller drive with single exhaust system or not: 480 hours or 10 years (if the engine is run at less than 480 hours);
55.2. water motorcycle engine: 350 hours or 5 years (if the engine is run at less than 350 hours);

55.3. uzkaram engines: 350 hours or 10 years (if the engine is run at less than 350 hours). 56. for each engine is added to the owner's manual in one of the languages of the European Union or its Member States in a specific language, in which the engine is offered in the market. This guide is: 56.1. engine installation and operating instructions to ensure proper engine performance under this rule 55;
56.2. specify engine power, measured according to the applicable standards. 57. Recreational craft with a built-in engine or engine with Z-shaped propeller driven without a single exhaust system, water motorcycles, uzkaram engine and engine with Z-shaped propeller drive with single exhaust system is designed, constructed and assembled so that noise emissions measured in accordance with the applicable standards specified tests, does not exceed that specified in annex 3 the noise emission limit values. 3. The notified body 58. Chapter 7 of these rules mentioned in the conformity assessment procedures shall be entitled to perform the conformity assessment bodies accredited to a government agency "Latvian National Accreditation Bureau" under the standard LVS EN ISO/IEC 17020:2005 "the main criteria for the various types of bodies performing inspection" requirements, or other Member States of the European Union notified body, on which the economy Ministry published a notice in the newspaper "Gazette" (notified body). 59. The notified body, its Director and the personnel conducting the inspection tests, the product may not be the recreational craft or components of the design engineer, manufacturer, supplier, installer or their authorised representatives. They may not be directly or as authorized representatives involved in this product design, manufacture, marketing or maintenance. 60. The notified body is independent and not controlled by neither the manufacturer nor the supplier. 61. This provision 60. the conditions referred to in paragraph 1 shall not preclude the possibility of exchanges of technical information between the manufacturer and the notified body. 62. The notified body shall have at its disposal the necessary human resources, financial resources and equipment, in order to be able to efficiently perform examination with the technical and administrative tasks. 63. the staff responsible for inspection shall comply with the following requirements: 39.2. appropriate technical and vocational education and training;
39.3. knowledge of the tests to be carried out and the test-taking experience;
63.3. design skills certificates, notes and reports, which are required to verify the tests. 64. the notified body shall ensure the impartiality of inspection staff. Staff remuneration does not depend on the number of tests or test results. 65. The notified body shall take out civil liability. 66. the staff of the notified body are obliged not to disclose the resultant professional activities of commercial information. 4. Recreational craft and their components of the structure of the market offering 67. The notified body shall take the necessary measures to ensure that the rules laid down in paragraph 3, the products are built and maintained according to the requirements, can offer the market and put into service according to its intended purpose only if they do not endanger the safety and health of persons, property or the environment. 68. Latvia is not prohibited, restricted or impeded the provision laid down in paragraph 3, the product offering on the market or putting into service If they are labelled with these rules specified in Chapter 9 and CE marking in conformity with the requirements of these provisions, including the conformity procedures set out in Chapter 7 of these rules. 69. in Latvia it is not prohibited, restricted or impeded the partly completed recreational craft of offering on the market, if the manufacturer, or his authorised representative established in the European Union, or person responsible for the placing on the market, in accordance with the provisions of paragraph 70, declares that the rest of the ship's construction will be completed. 70. The rules referred to in paragraph 69 of the manufacturer, his authorized representative in the European Union or the person responsible for the placing on the market, the Declaration shall include the following information: manufacturer, producer of 70.1. representatives of the European Union or the person responsible for the placing on the market, the name and address;
70.2. partially completed ship;
70.3. a statement that the partly completed construction of the vessel will be completed and that the ship complies with this construction applicable requirements. 71. in Latvia it is not prohibited, restricted or impeded the provision set out in section 7 of the construction component of the offering on the market and putting into service unless they are marked with the CE marking, is approved for compliance with the relevant essential requirements and these components are accompanied by a written declaration of conformity according to Chapter 10 of these rules, as well as where these components are intended to be incorporated in the rest of the ships in accordance with the provisions laid down in paragraph 70 of the Declaration submitted by the manufacturer, his authorized representative in the European Union or the person that these components offer the Latvian market. 72. Latvia is not prohibited, restricted or impeded the built-in engine or engine with Z-propeller propulsion without offering a single exhaust market, if these types are approved according to the laws and regulations on traffic not transportable mechanism used in internal combustion engines of pollutant emissions in the air, as well as the engine type approved according to the legislation on technical regulations for wheeled vehicles, requirements and components of prevention, and the compliance of the manufacturer or his authorized representative declares the engine parameters are relevant requirements of this regulation, when it will be installed in the vessel or watercraft, as specified in the manufacturer's instructions that came. 73. the manufacturer, his authorized representative in the European Union or persons ingredients offers a market of Latvia, the Declaration shall include the following: 73.1. the manufacturer, the manufacturer's representative to the European Union or persons ingredients offers a market of Latvia, name and address;
73.2. Description of components;

73.3. a statement that the component complies with the specific requirements. 74. The provisions referred to in paragraph 3, that the product does not meet the requirements of this regulation are allowed to expose the exhibitions, fairs and other events, if the mark is clearly visible in the clear that this product trading and commissioning is only allowed by their compliance in accordance with these rules. 5. Warranty conditions 75. If this provision in paragraph 7 of the design components or recreational vessels that have the CE marking and which is properly designed, constructed, installed, maintained and used in accordance with the intended purpose, may compromise the safety and health of persons, property or the environment, the consumer rights protection centre under the competence take steps to remove them from the market, prohibit or restrict the placing on the market and putting into service. Consumer rights protection centre shall immediately inform the Ministry of the economy, which, in turn, inform the European Commission of the said measures, specifying the reasons for its decision, especially where non-compliance is due to this provision, paragraph 5 of the non-compliance. 76. If the provisions of paragraph 7, the product is marked with CE mark, but does not meet the requirements laid down in these rules, the notified body, which controls the person who affixed them, take appropriate measures and inform the Ministry of the economy, which, in turn, inform the European Commission and the other Member States of the European Union representation. 6. the conformity assessment procedures Before the manufacturer launched the 77. the rules referred to in paragraph 3 of the vessels and their components production and placing on the market, he or his authorized representative in the European Union, having regard to the provisions of section 5 and the requirements laid down in this chapter in accordance with the rules set out in paragraph 10 of the recreational vessel categories. 78. the rest of the categories A and B vessels with a hull length of up to 2.5 12metr, take the internal production control plus tests (module Aa) or CE sample test (module B), complemented with the test specimen (C module) or any such module: B + D, or B + E, or B + F, or G, or H. 79. Category A and B recreational vessels with a hull length from 12 to 24 metres take the sample test, CE (module B), complemented with the test specimen (C module) or any such module: B + D, or B + E, or B + F, or G, or H. 80. category (C) recreational craft, hull length from 2.5 up to 12metr: 80.1. if applicable standards are complied with in respect of stability, free port and buoyancy, take the internal production control (module A), or the internal production control plus tests (module Aa) If the CE test sample (module B), complemented with the test specimen (C module) or any such module: B + D, or B + E, or B + F, or G, or H;
80.2. where non-compliance with the applicable standards for stability, free port and buoyancy, take the internal production control plus tests (module Aa) or CE sample test (module B), complemented with the test specimen (C module) or any such module: B + D, or B + E, or B + F, or G, or H. 81. Ckategorij the rest of the ships hull length from 12 to 24 metres take the sample test, CE (module B), complemented with the test specimen (C module) or any such module: B + D, or B + E, or B + F, or G, or H. 82. Category D recreational craft, hull length from 2.5 up to 24metr, take the internal production control (module A), or the internal production control plus tests (module Aa) or CE sample examination (module B) supplemented with the test specimen (C module) or any such module: B + D, or B + E, or B + F, or G, or H. 83. Recreational craft construction material using one of the following modules: B + C, or B + D, or B + F, or G, or H. One of these modules are also applicable: 83.1. pretaizdegšan equipment in all internal and rear engines;
51.7. protector against starting the engine when the gearbox is in neutral, all boarding engines;
83.3. corner rooms, steering mechanisms and cable assemblies;
83.4. fuel tanks and fuel hoses;
83.5. industrially produced hatches and scuttles. 84. A water bike, take the internal production control (module A), or the internal production control plus tests (module Aa) or the CE test sample (Bmodul), complemented with the test specimen (C module) or any such module: B + D, or B + E, or B + F, or G, or H. 85. Propulsion engines which are installed or specifically intended for installation on recreational craft or ūdensmotociklo, and engines significantly modified for the exhaust emission test samples made CE (module B), complemented with the test specimen (C module) or any such module: B + D, or B + E, or B + F, or G, or H. 86. Recreational craft with stern drive engines without integral exhausts or with inboard regarding noise emissions shall apply: 53.5. internal production control plus tests (module Aa) or module G or (H) module, where the test is carried out using the applicable standards for noise measurements; 86.2. internal production control (Amodul), or the internal production control plus tests (module Aa) or module G or H module when the estimate used for power/water-rate method, and the Frūd number ν-the speed of the ship; g — free fall acceleration; L: length of the vessel; 86.3. internal production control (module A), or the internal production control plus tests (module Aa) or module G or H module, if the assessment is used to refer to the ship's official data, established in accordance with this rule 86.1. section.

87. Water motorcycles, outboard engines and stern drive engines with integral exhaust which are intended for installation in recreation vehicles for noise emissions shall apply the internal production control (module A), or the internal production control plus tests (module Aa) or module G or H module. 7. Conformity assessment procedures 7.1. Internal production control (module A) 88. the manufacturer or his authorized representative in the European Union provide the products concerned are in conformity with the requirements of this regulation. The manufacturer or his authorized representative in the European Union, be marked with the CE marking and draws up a written declaration of conformity in accordance with the provisions of Chapter 10. 89. the technical documentation prepared by the manufacturer or its authorised representative in the European Union shall be kept for at least ten years after the last product has been manufactured. These documents are available to the market surveillance authorities for inspection. 90. If the manufacturer or his authorized representative is not in the European Union, technical documentation a person who distributes the product market of the European Union. 91. the product is in conformity with the requirements of these provisions valued at technical documentation, which includes the product design, production and operation, according to this provision description Chapter 8. 92. the manufacturer or his authorized representative shall keep a copy of the Declaration of conformity with the technical documentation. 7.2. Internal production control tests (module Aa, option 1) 93. Internal production control with the addition of Amodul to the test requires that the recreational craft shall take one or more tests for stability and buoyancy properties according to the requirements of these regulations or equivalent calculation or control. 94.93. These provisions the tests referred to in paragraph 1 or the equivalent calculation or control shall be carried out by the notified body chosen by the manufacturer. 95. One or more recreational vessels with integrated engine or engine with Z-shaped propeller driven without a single exhaust system and water motorcycles producer or on his behalf and selected by the manufacturer under the responsibility of the notified body carry out noise emission test. If one or more of the engines are tested, exhaust and noise emission conformity assessment (annex 4) to keep consistency. 96. One or more of the uzkaram engines and engines with Z-shaped Zen screw drive with single exhaust system engine producer or on his behalf and selected by the manufacturer under the responsibility of the notified body carries out noise emissions test as defined in section 2 of these regulations. If one or more of the engines are tested, exhaust and noise emission conformity assessment (annex 4) to maintain consistency. 97. If you test multiple engine manufacturer in order to verify the conformity of the sample comply with the provisions of annex 2 to these rules. 7.3. the CE test sample (module B) 98. Notified Body ascertains and attests that a specimen, representative of the production envisaged, meets the requirements of these regulations. 99. the application of the CE examination of the sample, the manufacturer or his authorised representative shall submit to the European Union notified body (optional). The application shall include the following information: 99.1. manufacturer's name and address (if the application is lodged by the authorised representative, the representative's name and address);
99.2. a written declaration that the application has not been lodged with any other notified body;
99.3. This provision referred to in paragraph 103 of the technical documentation. 100. The applicant shall place at the disposal of the notified body a specimen of the product (hereinafter sample). 101. The sample may cover several versions of the product provided that the differences between those versions do not affect the level of safety and the other requirements relating to a product. 102. If necessary, the notified body may request further samples, to carry out the test programme. 103. The technical documentation shall enable the conformity of the product with the requirements of this regulation. It includes (to the extent necessary for such assessment) product design, manufacture and operation of the description in accordance with the provisions of Chapter 8. 104. The notified body: 104.1. examine the technical documentation, verify that the model is built in accordance with the technical documentation and identify the components of the structure which are and which are not constructed in accordance with the applicable standards;
104.2. take appropriate and necessary tests to check whether the solutions adopted by the manufacturer meet the requirements of this regulation if the applicable standards have not been applied;
104.3. carry out appropriate inspections and tests necessary to check that the manufacturer's selected suitable standards are actually applied;

104.4. agree with the applicant on the inspection and verification of the required tests. 105. If the sample meets the requirements of these provisions, the notified body shall issue the applicant a CE certificate of inspection of the sample. The certificate shall contain the name and address of the manufacturer, conclusions of the examination, the conditions of validity and the information necessary to identify the approved sample. 106. The certificate is added to the relevant parts of the technical documentation. A copy shall be deposited at notified body that issued the certificate. 107. If the manufacturer is denied a sample certification, the notified body shall justify refusal to detail. 108. The applicant shall inform the notified body that holds the technical documentation concerning the CE examination certificate of the sample and of the changes to the approved product which requires additional approval where such changes may affect compliance with the requirements or conditions of use of the product described. Additional approval is given in the form of an addition to the CE examination certificate of the sample. 109. each notified body shall give the other notified bodies the necessary information on the CE sample examination certificates and certificates issued or refused the supplements. 110. The other notified bodies may receive CE sample inspection certifi cate and/or supplement it. The annexes to the certificates are available to the other notified bodies the Thai. 111. the manufacturer or his authorised representative shall keep the sample in CE examination certificate and its additions with the technical documentation a copy of at least ten years after the last product has been manufactured. 112. If the manufacturer or his authorized representative is not in the cou childhood, technical documentation, which markets the product in the European Union. 7.4 consistency (C module) 113. the manufacturer or his authorized representative in the European Union, ensures and declares that the products concerned conform to the pattern described in CE sample examination certificate and satisfy the requirements of this regulation. Manufacturer highlights each of the CE marking to the product and draw up a written declaration of conformity. The CE marking is accompanied by the identification number of the notified body which has carried out this provision set out in paragraph 147. 114. the manufacturer shall take necessary measures to ensure that the bags of izgat process ensures that the manufactured products conform to a model that describes the sample CE examination certificate and with the requirements of this regulation. 115. the manufacturer or his authorized representative shall keep a copy of the Declaration of conformity for at least 10 years after the last product has been manufactured. 116. If the manufacturer or his authorized representative is not in the cou childhood, technical documentation, which markets the product in the European Union. 117. If the manufacturer is not working under a relevant quality system as specified in these regulations, the manufacturer section 7.10 selected notified body to assess compliance with the exhaust emission requirements of this regulation, can perform extraordinary inspection without prior application. If the quality level is not satisfactory or if you need to check the manufacturer's data, perform the following procedure: from the series are checked out one engine and, subject to these terms as described in the chapter 2 test. The test engine powered Kit or separately (according to the manufacturer's specification). If the engine taken from the series exhaust emissions exceed this rules Chapter 2 limit, the manufacturer may ask for measurements to be performed repeatedly in the engine model of the series and the first sample that matched the exhaust emissions requirements of this regulation. To verify the conformity of the model engine requirements of these provisions, shall carry out conformity assessment (annex 4). 7.5. the product quality assurance (module D) 118. the manufacturer ensures and declares that the products concerned conform to the pattern described in CE sample examination certificate and comply with the requirements of this regulation. The manufacturer or his authorized representative in the European Union shall be marked with the CE marking each product and draw up a written declaration of conformity. The CE marking is accompanied by the identification number of the notified body which has carried out this provision set out in paragraph 147. 119. the manufacturer shall ensure that the provisions laid down in sub-section 7.10 of the high quality of the system and abide by the rules set out in paragraph 147. 7.6. The product quality assurance (module E) 120. the manufacturer or his authorised representative shall affix the CE marking to each product and draw up a written declaration of conformity. The CE marking shall be accompanied by the identification number of the notified body responsible for surveillance. 121. the manufacturer of the finished product inspection and testing is used for transmit quality exhausted system. 122. the quality system assessment and product quality inspection in accordance with the provisions of this sub-section 7.10. 123. Each notified body must, on request, give the other notified bodies information on issued and withdrawn the approval of the quality system. 7.7. the product verification (module F) 124. This module describes the procedure whereby the manufacturer or his authorized representative in the European Union checks and attests that the products subject to the requirements of this regulation, shall conform to a model that describes the sample CE examination certificate and with the requirements of this regulation. 125. the manufacturer shall take necessary measures for the manufacturing process ensures conformity of the sample described CE sample examination certificate and with the requirements of this regulation. The manufacturer or his authorized representative in the European Union shall be marked with the CE mark to each product and draw up a declaration of conformity. 126. The notified body shall carry out appropriate inspections and tests to check the conformity with the requirements of this regulation. Check after the choice of the manufacturer: 126.1. examining and testing every product in accordance with the provisions of paragraph 128;
126.2. checking and testing the products by statistical methods in accordance with the provisions of article 129. 127. the manufacturer or his authorized representative shall keep a copy of the Declaration of conformity for at least 10 years after the last product has been manufactured. 128. the examination and testing of products: 128.1. the product individually examined and tests defined in example in rojamo standards, or equivalent tests, to ensure that the product is in conformity with the look game specified CE sample examination certificate and with the requirements of this regulation;

128.2. the notified body shall affix, or cause to be affixed, its identification manufacturer number to each approved product and draw up a written certificate of conformity concerning the tests carried out;
128.3. the manufacturer or his authorized representative shall ensure that the notified body's certificates of conformity issued available upon request. 129. statistical verification: 129.1. the manufacturer shall present his products as a uniform group and must do to make the manufacturing process ensure the uniformity of each group produced;
129.2. all products shall be available for inspection in a uniform group. Choose from each group. Samples of the product of the individual checks and tests set out in the applicable standards, or equivalent tests, to ensure that the product is in conformity with the requirements of this regulation and to determine whether the group is validated or rejected;
129.3. statistical inspection, the following elements: 129.3.1. statistical method;
129.3.2. sampling plan with a description of its implementation;
129.3.3. the exhaust and noise emission conformity assessment (annex 4);
129.3.4. gas emissions in conformity assessment (annex 4);
129.4. If product is approved, the notified body shall affix, or cause to be affixed, its identification manufacturer number to each product and draw up a written certificate of conformity relating to the tests carried out. All products in the group can offer the market, except those who were identified as non-compliant;
129.5. If product is rejected, the notified body or the consumer protection centre shall take appropriate measures to prevent the sale of this product on the market;
129.6. If the product group has been rejected several times, the notified body may cancel the results of statistical tests;
129.7. If a notified body's responsibility, the manufacturer may affix the notified body's identification number during the manufacturing process;
129.8. the manufacturer or his authorised representative shall, on request, be produced to the notified body's certificates of conformity issued. 7.8. the unit verification (module G) 130. This module describes the procedure whereby the manufacturer ensures and de klar, the product that is the subject of this provision, paragraph 132 a certificate meeting the requirements of this regulation. The manufacturer or his authorized representative in the European Union must affix the CE marking to the product and draw up a declaration of conformity. 131. the notified body shall examine and testing of every product as laid down in the applicable standards, or equivalent tests, to check the conformity of the products with the requirements of this regulation. 132. The notified body shall affix, or cause to be affixed, its identification manufacturer number to the approved product and shall draw up a certificate of conformity relating to the tests carried out. 133. The technical documentation shall enable the conformity of the product with the requirements of these provisions and provide an explanation of the product's design, manufacture and use. 7.9. Full quality assurance (module H) 134. This module describes the procedure whereby the manufacturer who fulfils the obligations listed in the rules, ensures and declares that the products concerned meet the requirements of these regulations applicable to them. The manufacturer or his authorized representative in the European Union must affix the CE marking to each product and draw up a written declaration of conformity. 135. The CE marking supplemented by the identification number of the notified body responsible for the provisions set out in paragraph 147. 136. the manufacturer shall ensure that rule 7.10. sub-chapter quality system with respect to the product's design, manufacture and final inspection and testing, as well as the supervision order is subject to the rules set out in paragraph 147. 7.10. the quality system 137. to evaluate the quality system, the manufacturer shall provide the notified body application, which shall include information on the expected products and quality system documentation, as well as, where appropriate, technical documentation and CE sample a copy of the inspection certificate. 138. the quality system shall ensure compliance of the products with the requirements of these provisions and the CE examination certificate of the sample. 139. the elements adopted by the manufacturer, the requirements and the conditions for systematic document, presenting them as written plans, procedures and instructions. 140. the quality system documentation shall ensure a quality policy, procedures, quality programmes, plans, manuals and protocols for common understanding. 141. the quality system documentation includes: 141.1. the quality system objectives and structure, responsibilities and powers of the management with regard to design and product quality;
141.2. technical specifications, including the standards which will be applied (if standards were not applied in full, the-features that will be used to ensure that requirements are met);
141.3. control and construction design examination technical take, process and across Member in activities relating to the product category;
141.4. the corresponding manufacturing, quality control and quality assurance techniques, related to the processes and systematic actions;
141.5. the examinations and tests that will be carried out before, during and after manufacture, and inspection and testing frequency;
141.6. quality records (such as inspection reports and test messages, kalib catches news, qualifications of the personnel concerned messages);

141.7. features the required design and product quality supervision, protection of and effective operation of the quality system. 142. The notified body shall assess the quality system to determine its compliance with this provision, 138, 139 and 140.141. point requirements and assumes that a quality system which implements the applicable standard, meets these requirements. 143. the conformity assessment expert team has at least one person with experience in the product technology concerned. The assessment procedure includes a visit to the manufacturer's premises. 144. the decision shall be notified to the manufacturer. Notification shall include testing and evaluation in conclusion you justification. 145. The manufacturer shall undertake to fulfil the obligations arising out of the approved quality system, and maintain the quality system adequate and efficacious. 146. the manufacturer or his authorized representative shall inform the notified body of any planned quality improvement of this system. The notified body shall evaluate the modifications proposed and decide whether the premium quality system complies with this rule 138., 139, 140 and 141.. point requirements or needs assessment. The notified body shall notify its decision to the manufacturer. The notification shall contain the conclusions of the examination and the grounds for the decision. 147. The notified body: 147.1. checks to make sure that the manufacturer duly fulfils the obligations arising out of the approved quality system;
147.2. periodically carry out audits to make sure that the manufacturer maintains and applies the quality system and provide the manufacturer with audit reports;
147.3. without warning can make the manufacturer's inspection. Such inspection the notified body may carry out tests or have them carried out, to check the quality of the system. The notified body must provide the manufacturer with an inspection report and, if a test has taken place, and the test results. 148. the notified body To perform the test, the manufacturer provides free access to it's design, manufacture, inspection, testing and storage locations and provide all required information including: 148.1. quality system documentation;
148.2. quality records, relating to the construction (the results of analyses, calculations, tests);
148.3. quality records that are related to the production (inspection reports, test and calibration results, qualifications of the personnel concerned ones). 149.10 years after the last product has been manufactured, keep at the manufacturer of such control bodies available documents: 149.1. the quality system documentation;
149.2. documentation on the quality system improvements;
149.3. notified body decisions and reports on quality system compliance with applicable standards, periodic audits and on the manufacturer additional tests. 150. Each notified body must, on request, give the other notified bodies information on issued and withdrawn the approval of the quality system. 8. The manufacturer's technical documentation submitted 151. Modules A, B, C, D, G and E referred to in the technical documentation includes information, and the way the manufacturer provides the constructive components of vessels and their compliance with the requirements. 152. technical documentation provides information about the product's design, manufacture, installation and operation and assess compliance with the requirements of this regulation. 153. in order to carry out the evaluation, the technical documentation includes: 153.1. General description of the sample;
153.2. conceptual and storyboard drawings of parts, assemblies, and other elements of the scheme, as well as the explanatory descriptions and instructions for use of the product;
153.3. list of applicable standards applied in full or in part, and descriptions of the solutions adopted to meet the requirements of this regulation if the applicable standards are not applied;
design and calculation of 153.4. results of checks;
153.5. test results or estimates regarding stability in accordance with the provisions of paragraph 17 of the conditions and buoyancy in accordance with the provisions of paragraph 18;
153.6 exhaust emission test protocol, showing compliance with this provision the requirements of Chapter 2;
153.7. noise emission test report or a reference to the ship's data, showing compliance with these rules in Chapter 2 requirements. 9. the CE marking 154. Recreational craft, water motorcycles, uzkaramo engines, engines with Z-shaped propeller drive with single exhaust system and the rules referred to in paragraph 7 of the design components which comply with this provision in paragraph 5 the requirements placed on the market, shall be marked with the CE marking. 155. the CE marking is located on the Recreation Board on water motorcycles and to this rule set out in section 7 of the design components and their packaging. The CE marking is clearly visible, legible and indelible. The CE marking is accompanied by the identification number of the notified body which has carried out of Aa, (D), (F), (G) and (H) the procedures in the module. 156. it is prohibited to place on the products listed in these rules marks or inscriptions which are likely to mislead third parties as to the meaning or form of the CE marking. Other signs can be placed on the products listed in these rules and their packaging provided that the visibility and legibility of the CE marking is not thereby reduced. 157. If a notified body establishes that the CE marking is positioned incorrectly, the manufacturer or his authorized representative in the European Union is obliged to end the infringement. 158. If further failure to comply with the requirements set out in these rules for the labelling of the product, the notified body shall take measures to limit or prohibit the placing on the market of such products, or to ensure that it is withdrawn from the market, subject to this provision in the chapter 4 requirements. 10. the written declaration of conformity for 159. The written declaration of conformity with the requirements of this regulation are located: 159.1. recreational craft and water motorcycle, and it's in the owner's manual;
159.2. This provision at paragraph 7 of the said ingredients;
159.3. at engine, and it is added to the owner's manual. 160. The written declaration of conformity shall include the following: 160.1. the manufacturer or his authorized representative in the European Union the name and address;
160.2. recreational craft, water motorcycle, or this rule 7, paragraph description of ingredients;
160.3. references to relevant applicable standards or references to instructions, in accordance with which conformity is declared;
160.4. If necessary, the reference to other legislation;

160.5. this information, if necessary for CE sample examination certificate issued by a notified body;
160.6. If necessary, the notified body name and address;
160.7. the data of the person, the signatory who has been empowered to represent producers in the European Union. 161. the written declaration of conformity is issued in one of the languages of the European Union or its Member States in a specific language, in which the engine is offered in the market. 162. with regard to the rules referred to in paragraph 64 of the engines in addition to the Declaration of conformity that rule 160. the information specified in point include a statement by the manufacturer that the engine exhaust emissions will correspond to the requirements of these regulations, if the engine is to be installed on recreational craft, in accordance with the manufacturer's instructions and added, if necessary, that this engine must not be put into service until the rest of the Board declared (in which it installed) compliance with the relevant provisions. 11.163. Market surveillance market surveillance authority under the national budget resources to fulfil consumer centres. Consumer rights protection Centre carries out the laws and measures to prevent the provision of inadequate recreational vessels and their equipment distribution market. 164. If the rest of the ship and its equipment, the manufacturer or his authorized representative in the European Union has not fulfilled the requirements laid down in these provisions, the trade of the product concerned is not permissible. 12. The final issue 165. Be declared unenforceable in the Cabinet's April 1, 2003, the provisions of no. 144 "rules on the rest of the shipbuilding, the assessment of conformity and placing on the market" (Latvian journal, 2003, nr. 53; 2004, nr. 68). Informative reference to European Union directives, the regulations include provisions resulting from: 1) of the European Parliament and of the Council of the European Union of 16 June 1994, Directive 94/25/EC "on the Member States ' laws, regulations and administrative provisions relating to recreational craft";
2) of the European Parliament and of the Council of 16 June 2003 of Directive 2003/44/EC on the approximation of the laws, regulations and administrative provisions of the Member States relating to recreational craft ". Prime Minister a. Halloween traffic Minister a. shlesers annex 1 Cabinet of 30 august 2005, regulations no 647 CE conformity mark 1. CE marking consists of the capital letters CE that depict the following: 2. the CE marking of size can be increased or reduced, following the sample proportions. 3. The two components of the CE marking are the same size, and it may not be less than five millimeters. 4. the CE marking supplemented by the identification number of the notified body, if it participates in the control of production, as well as with the last two digits of the year when the product is marked with CE marking.
Traffic Minister a. shlesers annex 2 Cabinet of 30 august 2005, regulations no 647 engine exhaust emission (g/kWh) no PO box

Carbon monoxide CO = A + B/Hidrokarbonāt HC PnN = A + B/a of nitrogen oxides NOx PnN notes PT type (A) (B) (A) (B) n n 1. Two-stroke engine, the spark ignition is not used jam 2 150.0 600.0 1.0 30.0 100.0 0.75 10.0. Four-stroke engine, the spark ignition is not used jam 3 150.0 600.0 1.0 6.0 50.0 0.75 15.0. compression ignition 5.0 1.5 2.0 0.5 9.8 1.0 0 0 notes. 1. A, B and n are constants in accordance to the table. 2. PN is the rated engine power in kilowatts (kW). 3. the exhaust emissions are measured in accordance with applicable standards. 4. the engines with a capacity of more than 130 kW, you can use the E3 (IMO) or E5 (recreational vessels) work cycle. 5. Emission test fuels used in gasoline and diesel engines comply with the legislation on technical regulations for wheeled vehicles, requirements and conformity assessment of ingredients.
Traffic Minister a. shlesers annex 3 Cabinet of 30 august 2005, regulations no 647 noise emission limits for single engine power in kilowatts maximum sound pressure level (LpASmak.) in decibels PN = PN = PN = 40 72 10 67 10 < 40 75 notes. 1. PN-rated engine power in kW rated for the speed of rotation. 2. LpASmak. — the maximum sound pressure level in DB. 3. All types of engines with dubultdzinēj and compound engine unit can apply 3 decibels. 4. Recreational craft with inboard engine configuration or stern drive engine without integral exhaust shall be deemed to conform to the requirements, if Frūd is equal to the number of 1.1 and a power and water residue ratio is equal to 40 and where the engine and exhaust system are installed in accordance with the engine manufacturer specifications: 4.1 Frūd the number is calculated using the following formula: where: a the maximum speed of the vessel ν (m/s); LWL-waterline length (in metres); g — free fall Acceleration (g = 9.8 m/s2); 4.2. capacity and water residue ratio is calculated using the following formula:, where P-engine power (kW); D-water residue.
Traffic Minister a. shlesers annex 4 of the Cabinet of Ministers of 30 august 2005, regulations no 647 of the exhaust and noise emission conformity assessment 1. Engine series for verification of conformity of the series is taken. The manufacturer determines the number of samples (n) is required and agree on them with the notified body. 2. The mean size X, derived from the results of the sample, is calculated for each of the exhaust and noise emission adjustable component. Consider that series production meet the requirements (pass decision) if the following conditions are met: + k x S X ≤ L, S – standard deviation calculated using the following formula: S2 = (x-X)-1990s 2/(n-1); X — the arithmetic mean of the results; x-sample individual result; L — the limit size; n — number of engines in the series; (k) — a statistical factor depending on n (see table). Table 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 0.973 0.613 0.489 0.421 0.376 0.342 0.317 0.296 0.279 n n k k 0.265 0.253 0.242 0.233 0.224 0.216 0.210 0.203 0.198 if n ≥ 20, k = 0,860/√ n then traffic Minister a. shlesers