Cabinet of Ministers Regulations No. 747 in 2005 (October 4. No 56 2) rules for European technical approval is Issued in accordance with the law "on conformity assessment" of article 7 and article 22 of the law on construction of the second part 1. General questions 1. determines the content of the European technical approval and issuance procedures.
2. the European technical approval for construction products is a positive technical assessment according to the intended purpose of use based on the būviz strādājum conformity with the essential requirements of the construction that it is intended to be incorporated. The essential requirements are defined in the Latvian construction et seq of the LBN 006-00 ' essential requirements ' structures, approved by the Cabinet on March 27, 2001 regulations No 142 "rules for the Latvian et seq of the LBN 006-00" essential requirements "in buildings" (hereinafter referred to as the Latvian et seq of the LBN 006-00 "essential requirements construction").
3. the European technical approval is issued by: 3.1 for construction products which have not issued the European harmonised stan darts, the European Commission recognised in a Member State of the European Union a national standard or the European Commission issued a mandate to the European harmonized standard for the development and the European Commission, after consulting the Standing Committee on construction is the finding that standard cannot or cannot yet be elaborate;
3.2. for construction products which differ significantly from the construction products which are made to harmonised European standards or recognised by the European Commission of one of the Member States of the European Union national standards;
3.3. for construction products, for which the European Commission has already issued a mandate to the European Committee for standardisation or the European Committee for Electrotechnical Standardization in the European harmonized standard for the design or to which the European Commission has found that the following harmonised European standards can be developed only on the mandate issued by the European Commission and the European Commission specified period.
4. If the mandate of the European harmonized standard development is issued, the provisions referred to in point 3.1. conditions do not exclude the issue of European technical approval for construction products, for which the rules are set in accordance with the issued guidelines for European technical approval. In this case the European technical approval is valid until the entry into force of the harmonized European standard.
5. The Ministry of economy is the institution responsible for the granting of European technical approval for Latvia and for the provision of European technical approval for withdrawal in accordance with the procedure laid down in these rules, where the European technical approval do not comply with this provision, in paragraph 3, the requirements or does not support the LBN Latvian et seq 006-00 "essential requirements construction" that the requirements are met.
2. the European technical approval izdevējinstitūcij 6. in Latvia the European technical approval for construction products in accordance with the procedure laid down in these provisions shall be issued by the authorized institution of the Ministry of Economic Affairs (hereinafter referred to as the technical approval authority), which is selected in an open tender.
7. technical approval authority issuing European technical approval, on the basis of a written application submitted by the manufacturer or its authorised representative established within the European economic area country and is specifically authorized to submit the request for European technical approval of application (hereinafter the applicant).
8. technical approval bodies and experts involved in the preparation of the European technical approval: 8. on the basis of scientific knowledge and practical knowledge, able to assess the appropriateness of the use of new materials;
8.2. in these terms and the ability to carry out the Cabinet of 30 April 2001, regulations No. 181 "construction products conformity assessment procedures of regulated accounts dad sphere" those requirements;
8.3. can accept from the manufacturer or their authorized representatives, interest is no pendent decisions;
8.4. the ability to objectively and fully assess the contribution of all interested parties;
8.5. is apdrošinājuš its civil liability.
9. On the technical approval of the authorization of the Ministry of economy shall notify the European Commission and published in the relevant information in the newspaper "journal".
3. the European technical approval request 10. The applicant may request the issuance of European technical approval for construction products, materials for the kit or būvizstrādāj mu family in only one Member State of the European Union authorised the European technical approval izdevējinstitūcij (hereinafter Member State notified ETA izdevējinstitūcij). If the applicant has requested the issue of a European technical approval for construction products or the products of a particular family in another Member State of the European Union, the applicant is not entitled to request European technical approval for the issue of the US prices for the same products, or materials of construction kit family technical approval institution in Latvia.
11. Requests the European technical approval authorities, technical approval the applicant agrees that the technical approval of the content of the application, the institution shall inform the European Commission, the European technical approval bodies authorised by Member States in the Secretariat and the izdevējinstitūcij.
12. The applicant before the application can be requested from the technical approval institutions following written information: 12.1. preparation for European technical approval and allocation procedures;
12.2. the timetable that technical approval authority required to perform certain construction products in the European technical approval shall prepare the horse and picking (technical approval) procedure;
12.3. technical approval procedures cost estimate and payment arrangements.
13. If the area of construction products have not yet been approved as complying with European technical approval or if the construction satisfies that rule 3.1. and 3.2., the conditions referred to in this provision of the information referred to in paragraph 12, the applicant provided only once in accordance with the provisions of section 4.2 that procedure is a decision on the possibility to issue European technical approvals and technical approval authority has been informed about it.
14. the application shall be accompanied by a description of the products, specifications, and testing you race reports that details of construction that is required for a European technical approval, and its intended use.
15. the application shall specify all possible shop construction and location. The applicant shall ensure that the technical approval of specialists or its authorised institution experts technical approval process can visit the shop floor during their work.
16. Submission (annex 1) shall be submitted in the language of the country. The application attached noto documents shall be submitted to the national language or in English. If the documents annexed to the application submitted in English, technical approval authority may require the applicant to submit, within two months, of any or all of the gum cold translations of documents connected to the Latvian language. These translations should be considered part of the application.
17. If the application is accepted, the technical approval authority Adm in nistratīv process within the time limit set by law certifying the receipt of the application and readiness to start a technical approval procedure and invited the applicant to contract for technical approval procedures (annex 2).
18. If the application is rejected, the institution of technical approval decision shall state the reasons for rejection. In this case, the applicant may: 18.1. technical approval authority to challenge the decision of the administrative procedure law;
18.2. to submit the application to the other Member States authorized ETA izdevējinstitūcij.
19. technical approval body shall have the right to request the applicant to submit documents, test reports, estimates and other information required for the technical approval of the construction procedure and evaluation of conformity with regard to the validity of the intended use.
20. The applicant shall provide a technical approval bodies and its full varoto experts who assess the technical approval of construction and, with the necessary information and documents.
21. technical approval authority is entitled to withdraw the application, if, within two months after sending the reminder the applicant does not fulfil the obligations referred to in these provisions or requirements necessary for the adoption of technical approvals.
22. technical approval authority and its authorized experts ensure the confidentiality of the information of this that they become known, considering the cold gum and acting for European technical approvals.
4. European technical approval 23. preparation and granting European technical approval shall be issued in accordance with these provisions, and 23.1.: Cabinet 30 April 2001 fixing the tions No. 181 "construction products conformity assessment procedures for the regulated sphere";

23.2. the common procedural rules for European technical approval for the request specified in Commission on 17 January 1994 decision 94/23/EC;
23.3. the relevant guidelines, specifying their number and name if one European technical approval in accordance with the Council of 21 December 1988 of Directive 89/106/EEC on the approximation of the laws, regulations and administrative provisions of the Member States relating to construction products (hereinafter Directive 89/106/EEC) article 9 (2) of the rules of procedure and the total 3.2 is not issued without guidelines.
24. the European technical approval based on Directive 89/106/EEC construction products inspections, tests and conformity assessment in accordance with the strādājum or būviz family of construction guidelines and explanatory documents for the European Council of 21 December 1988 Directive 89/106/EEC on the approximation of the laws, regulations and administrative provisions of the Member States relating to construction products (hereinafter referred to as Interpretative documents) (released as the European Commission's 1994 report 94/C 62/01 and published in the official journal of the European Union on 28 February 1994 (series a C62 37. volume)).
25. If the European technical approval guidelines have not yet been issued, European technical approval may be issued with reference to construction products designated with the essential requirements and the interpretative documents (if the construction products conformity assessment is approved by the Member States, the notified body issuing the ETA, which the European Organisation for technical approval).
26. the European technical approval and CE marking of construction products declares the conformity of construction products with the essential requirements of the Latvian et seq of the LBN 006-00 "essential requirements construction" and the interpretative documents. If the European technical approval are taken into account and evaluated other aspects of construction products, which do not relate to the essential requirements and the non-regulated area, such evaluation should be clearly distinguished and the European technical approval must specify that it refers to the non-regulated areas.
27. the European technical approval shall be issued for a period of up to five years. This period may extend this provision in Chapter 6, in that order.
28. technical approval procedures and the European technical approval of the issue of the cost to you in accordance with the annexed to the Treaty on the approval of the technical procedures, shall be borne by the applicant.
4.1. preparation of the European technical approval and in accordance with the guidelines issue 29. European technical approval guidelines for construction or construction product family developed in accordance with the mandate issued by the European Commission.
30. the European technical approval guidelines technical approval by the institution in the development of the European technical approval Organisation Committee of the technical Council created.
31. the guidelines for European technical approval shall include the following information: 31.1. Explanatory reference to relevant documents;
19.4. specific requirements for construction products or materials essential to the sai mei sliding requirements of Latvian et seq of the LBN 006-00 "essential requirements in buildings";
31.3. methods of testing of construction products;
19.5. the evaluation of the test results and documentation techniques;
31.5. inspection and conformity assessment practices in accordance with Cabinet of Ministers 30 April 2001 No. 181 of the provisions "of the construction products conformity assessment procedures for the regulated sphere" annexes III, IV and VII;
19.6. the European technical approval expiration date.
32. The transitional period by the European technical approval organisation down each specific guidelines for European technical approval for a project to examine the draft of the European technical approval comparability with those of the other Member States for the notified ETA izdevējinstitūcij issued to European technical approvals, prepared the draft of the European technical approval, together with its accompanying documents and test reports, technical approval authority shall forward its opinion to the provision: 32.1. notified the other Member States of izdevējinstitūcij;
32.2. the European technical approval to the Secretariat of the organization.
33. Opinions on the guidelines for European technical approval for the project and the project of the European technical approval of this provision in paragraph 32 of that institution during the two months provided no information on the technical approval and project developer.
34. the European technical approval guidelines (also in the other Member States of the Council of izdevējinstitūcij prepared EIT Roto guidelines) after consultation with the Standing Committee Codes construction of technical approval body shall publish in a newspaper "journal".
35. The European technical approval for the technical implementation of the project the institution sends the approval class(es) and opinions: 21.8. notified the other Member States of izdevējinstitūcij;
35.2. the European technical approval to the Secretariat of the organization. European Organisation for technical approval of the projects mentioned by the Secretariat sent to the European Commission.
36. technical approval issued by the institution and published in the European technical approval: 36.1. notify all other Member States notified ETA izdevējinstitūcij;
36.2. the information shall be published in the newspaper "Gazette";
36.3. the authorised in other Member States at the request of the ETA izdevējinstitūcij send them the European technical approval is issued a full set of supporting documents.
4.2. preparation of the European technical approval and issue, if the guidelines are not issued 37. technical approval by the institution receiving an application in accordance with the provisions of paragraph 13 or an entirely new applications (innovative) būviz strādājum or family of construction products European technical approval, consult with the European Organisation for technical approval of the technical Council for the harmonisation of European technical approval for construction products without assignment for European technical approval guidelines (under 13 and 25 of these rules) and reach agreement on conformity assessment proc is a fist.
38. The European technical approval organisation Technical Council agree that the application complies with the provisions of this subparagraph 3.1, the European Organisation for technical approval of the President of the European Commission requested a mandate to issue European technical approvals.
39. If the European technical approval is issued in accordance with this set of 25 mu (not guidelines), its content and structure under the Commission of 22 July 1997 decision No 97/571/EC on construction products is the General format of European technical approval.
40. The European technical approval organisation Technical Council can not agree to issue European technical approvals, "said mu sends the Organization the European technical approval for the Executive Committee. European Organisation for technical approval of the Executive Committee shall decide whether an issue submitted for consideration by the European Commission within the Standing Committee on construction. Technical approval authority shall inform the applicant for the construction of the decision taken by the Standing Committee.
41. The European technical approval organisation is agreed fucking for issuing European technical approval without guidelines, technical approval authority shall consult the other Member States notified ETA izdevējinstitūcij of the European technical approval applied for the preparation of the course of the testing programme and the construction products conformity assessment procedures. Technical approval authority of the other Member States, take into account the opinion of the authorised izdevējinstitūcij. If other Member States notified ETA izdevējinstitūcij findings objections cannot be taken into account, the differences discussed the organisation of the European technical approval of the technical Council and Executive Committee meetings.
42. If the application of the European technical approval refers to the būviz strādājum or family of construction products, for which the rules of procedure referred to in paragraph 37 is already established, the issue of the European technical approval shall be based on the existing order.
43. The European technical approval Before issuing technical approval you institution prepared the project of the European technical approval is sent (with a request to give feedback within two months) for their consideration and opinions: 43.1. notified the other Member States of izdevējinstitūcij;
43.2. the European technical approval to the Secretariat of the organization.
44. If that rule 43, paragraph authorities have given approval to the technical approval authority to the applicant the European technical approval. European technical approval is issued by technical institution rinājum transmit circulate all this provision in paragraph 43 of the said institutions.
45. If notified by the Member States of the provisions of the ETA izdevējinstitūcij. 43 and 44 in the order referred to in paragraph agree fails, the matter shall be submitted for examination to the European Organisation for technical approval in the technical Council. If the technical Council, technical approval authority to the applicant the European technical approval. If the agreement fails to achieve, the question of the European Organisation for technical approval of the Executive Committee and shall take a decision on the draft of the European technical approval for future progress.

5. the withdrawal of the European technical approval and amendment of 46 if the European Commission informs that in Latvia the European technical approval issued does not comply with the provisions of paragraph 3 above requirements or does secure the Latvian et seq of the LBN 006-00 "essential requirements construction" of those requirements, the economy Ministry said the European technical approval is issued, and shall inform the institution of the technical approval of construction products and the manufacturer or his authorised representative to the European economic area country. The Ministry of economics for the European technical approvals of construction products to the withdrawal shall inform the organisation of the European technical approval of the Secretariat and other Member States notified ETA izdevējinstitūcij, as well as the owner of the European technical approval.
47. technical approval authority may amend only the European technical approval is issued.
48. the amendment of the European technical approval shall be made in accordance with the new issue of the European technical approval (Chapter 4 of these rules), technical approval procedure exposing its European technical approval you have parts that are amended.
49. the Issue of the amended European technical approval, the technical body validating you revoke the existing European technical approval.
6. the European technical approval expiration date extension 50. European technical approval of application, the period of validity of the definition of the paunch, the applicant Chapter 3 of these rules in the order presented in the technical approval body at least six months before the European technical approval expiration date. Technical approval authority extended only in Latvia for European technical approval is issued.
51. the European technical approval may be extended to up to five years, unless the European Commission is informed by the European Organisation for technical approval or the approval of the technical authority that changed the conditions on the basis of which the European technical approval is issued.
52. the application for a European technical approval for the extension of the period of validity of the construction products appropriate for European technical approval guidelines in certain documents.
53. If the European technical approval is to be issued without a European technical approval guidelines in accordance with the provisions of subsection 4.2, deliverables documents technical approval authority determines, after consultation with the organisations of the European technical approval for the Secretariat and other Member States notified ETA izdevējinstitūcij.
54. the European technical approval expiration date is extended in accordance with the new issue of the European technical approval (Chapter 4 of these rules).
Informative reference to European Union directives, the regulations include provisions resulting from: 1) Council of 21 December 1988 of Directive 89/106/EEC on the States carry the approximation of laws, regulations and administrative provisions relating to construction products;
2) Council of 22 July 1993 of Directive 93/68/EEC amending Directive 87/404/EEC (simple pressure vessels), 88/378/EEC (safety of toys), 89/106/EEC (construction products), 89/336/EEC (electromagnetic compatibility), 89/392/EEC (machinery), 89/686/EEC (personal protective equipment), 90/384/EEC (non-automatic weighing instruments), 90/385/EEC (active implantable medical devices), 90/396/EEC (appliances burning gaseous fuels) , 91/263/EEC (telecommunications terminal equipment), 92/42/EEC (new water heaters that heat with liquid or gaseous fuels) and 73/23/EEC (electrical equipment designed for use within certain voltage limits);
3) Commission of 17 January 1994 decision 94/23/EC on the common procedural rules for European technical approval;
4) Commission of 22 July 1997, decision No. 97/571/EC on construction products is the General format of European technical approval.
Prime Minister a. Halloween — Minister of Economy Minister e. Repše Editorial Note: the entry into force of the provisions by 8 October 2005.
 
1. the annex to Cabinet of 4 October 2005, regulations no 747 economy Minister, the Defense Minister e. Repše annex 2 Cabinet of 4 October 2005, regulations no 747 economy Minister, the Defense Minister e. Morgan