Cabinet of Ministers Regulations No 535 Riga, 27 June 2006 (pr. No. 34) agricultural or forestry tractors, their trailers and component conformity assessment Issued in accordance with the provisions of the Highway Traffic Act, the fourth subparagraph of article 15.1 i. General questions 1. terms used in the rules: 1.1. Ec type-approval procedure, certifying that the vehicles, systems, components or separate technical units type meets the requirements of this regulation;
1.2. "multi-stage EC type-approval procedure, certifying that the completed or not (depending on the State of) the vehicle type satisfies the requirements of this regulation;
1.3. the approval of single vehicles – a procedure with which certifies that a vehicle approved individually satisfies the national vehicle conformity assessment requirements;
1.4. vehicle means any incomplete, completed in one stage or the Nepabeigts tractor, trailer or interchangeable towed machinery for use in agriculture or forestry;
1.5. vehicle category: any set of vehicles which have identical design characteristics;
1.6. vehicle type-of a particular category of signs which are not significantly different from the provisions of annex 1 (A) characteristics referred to in chapter (here are also allowable variants and versions of a type of vehicle);
1.7. basic vehicle-any incomplete vehicle, the vehicle identification number of which is preserved from the process of multi-stage EC type-approval in subsequent stages;
1.8. the incomplete vehicle: any vehicle which still needs completion in at least one further stage in order to meet all the requirements of this regulation;
1.9. the complete vehicle – a vehicle that, upon completion of the process of multi-stage EC type-approval, at all stages of meeting the requirements of this regulation;
1.10. any motor-tractor, wheeled or tracked agricultural or forestry motor vehicle having at least two axles and a maximum design speed of not less than 6 km/h, the main function of the drawbar pull is and which is specially designed to tow, push, carry and operate the changeable equipment designed agricultural or forestry work, or to tow the trailer. It may be adjusted load carrying performance of agricultural or forestry work, and be equipped with passenger seats;
1.11. trailer: any towed device intended mainly agricultural or forestry goods and designed for towing by tractor. This category includes the trailer, which is part of the load to the towing vehicle. Any vehicle coupled to the tractor and equipped with fixed installations shall be assimilated to the trailer, where that vehicle is the technically permissible total mass to unladen mass ratio 3.0 or higher and if the vehicle is not designed to process materials;
1.12. interchangeable towed machinery: any trailer, used in agriculture or forestry which is designed to be towed by a tractor and changes or adds to the functional capabilities of the tractor. It may be with a cargo platform, designed and built to hold all mechanisms and devices necessary for those objectives, and temporarily store materials produced or needed work. Any vehicle intended to tow with a tractor and equipped with fixed installations or designed materials processing are considered interchangeable towed machinery if that vehicle is the technically permissible total mass to unladen mass ratio less than 3.0;
1.13. the system-related devices connected to perform special functions in the vehicle;
1.14. ingredient – a device, intended to be part of a vehicle, which may be type-approved independently of a vehicle;
1.15. "separate technical unit-a device, intended to be part of a vehicle, which may be type-approved separately but only in relation to one or more specified types of vehicles;
1.16. manufacturer: the natural or legal person that EC type-approval authority responsible for type-approval process all formalities and for the compliance of the product and that for his own use, designs, has designed its, manufactures or has manufactured a vehicle, system, component or separate technical unit. The placing on the market or put into service a vehicle, system, component or separate technical unit, the manufacturer is responsible for ensuring compliance with those rules. The manufacturer shall also be deemed to be a manufacturer's representative to the European economic area are natural or legal persons established in, which the manufacturer has appointed in it to represent her activities with the EC type-approval authority and the manufacturer's task to deal with the areas defined by these regulations;
1.17. commissioning – any vehicle the first use for its intended purpose in these provisions, before which the manufacturer requires no installation or adjustment. The date when the vehicle is registered or placed on the market for the first time shall be considered the date of entry into service;
1.18. the EC type-approval authority, the body responsible for all vehicle, system, component or separate technical unit type-approval formalities and issued or withdrawn EC type-approval, and of the measures taken by the manufacturer to ensure product conformity;
1.19. testing laboratory-a body which tests or inspections carried out the EC type-approval authority. This function may also be carried out by the EC type-approval authority itself;
1.20. the individual directives-directives listed in this provision in chapter B of annex 1;
1.21. information document-form specified in annex 2 to these regulations, which set out what information is provided by the applicant;
1.22. the information folder – the folder or document with data, drawings and photographs required as per annex 2 of this provision and that the applicant submitted to the testing laboratory or the EC type-approval authority;
1.23. information package – the information folder plus any test reports or other documents requested in the separate directives that, in carrying out its tasks, added to the information folder in the testing lab, or the EC type-approval authority;

1.24. the index to the information package, the document setting out the contents of the information package. It is numbered or highlighted to all pages would be transparent and clearly listed;
1.25. the certificate of conformity – this provision is specified in annex 3 of document that is issued by the manufacturer to certify that a particular vehicle type approved in accordance with these provisions, at the time of manufacture answer to all the requirements laid down in these regulations and in the separate directives, confirm that the no additional checks may be registered or put into service in all Member States.
2. the rules provide: 2.1. conformity assessment procedures of General vehicles as defined in point 1.4;
2.2. the conformity assessment procedures of vehicle systems, components and separate technical units.
3. These provisions shall not apply to: 3.1. vehicles registered in foreign countries and for a period of up to three months from there;
3.2. individual vehicle approval;
3.3. machinery specially designed for forestry use (such as skidders and forwarders) and comply with the standard EN ISO 6814:2005 "– mobile machinery and self-propelled machines – terms, definitions and classification";
3.4. forestry machinery based on chassis for earthmoving and comply with the standard LVS EN ISO 6165:2003 "earth moving machinery – basic types-dictionary";
3.5. interchangeable machinery that is fully raised above the ground when the vehicle to which it is attached is in use on the road;
3.6. new vehicles belonging to categories T1, T2 and T3, which is put in service until July 1, 2009;
3.7. the new T4, T5, C, R and S in category types until July 1, 2009. 
II. The type approval procedure General 4. Vehicles and components in conformity assessment shall be carried out by the national agency "Latvian National Accreditation Bureau" to the standard LVS EN 45011:2004 "the main criteria for the different types of institutions that deal with product certification accredited state systems" limited liability company "certification and testing centre" (hereinafter referred to as the Centre) or notified body of another Member State, for which the Ministry of Economic Affairs has published a notice in the newspaper "journal".
5. vehicle testing and examination by the State Agency "Latvian National Accreditation Bureau" to the standard LVS EN ISO/IEC 17025:2005 "the competence of testing and calibration laboratories-General requirements" accredited Centre or another Member State notified body, on which the Ministry of Economic Affairs has published a notice in the newspaper "Gazette" (hereinafter referred to as the testing lab).
6. to confirm the vehicle in Latvia or the component type, the manufacturer of each type to be approved shall be submitted to the individual application.
7. the application shall be accompanied by an information folder containing: 7.1. information document, which contains the type of vehicle or component in the technical description in accordance with the requirements of this regulation;
7.2. conformity assessment required for the vehicle or component type drawings and photos;
7.3. the manufacturer or held other independent testing lab reports and other documents that can provide information on the type of vehicle or component;
7.4. the model of the certificate of conformity (annex 3), with which the manufacturer certifies each specific vehicle to conform to the approved type and indicating the person (including post) the names, surnames and signatures, which are allowed to sign the certificates of conformity.
8. the Centre shall within 30 working days of the evaluation and of the documents submitted for type approval of the vehicle applied sample (chosen by random selection method) checks awarded: 8.1. Ec type-approval of a vehicle type comply with the technical description and submitted these provisions listed in annex 1 as well as treating the rule in chapter C of annex 1 specific model EC type-approval certificate specified examinations;
8.2. multi-stage EC type-approval to incomplete or completed vehicle type, having regard to the State of completion of the vehicle (annex 4);
8.3. component type-approval of a vehicle type comply with the technical description and submitted to the requirements of this regulation;
8.4. the type-approval of a component type that corresponds to the technical description and submitted to the requirements of this regulation.
9. the issue of the EC type-approval certificate for a vehicle or component type, the Centre shall follow the following procedures: 9.1 if the system, component or separate technical unit fulfils its function or if its special function gets only with other parts of the vehicle and if so of compliance with one or more requirements can be certain that when the representative of the system, component or separate technical unit works in conjunction with other industrially manufactured or simulate parts of the vehicle such system, component or separate technical unit type-approval certificate shall specify any restrictions on its use and any conditions for fitting it;
9.2. for each vehicle type for which the Center has assigned, or is refused by a reference the type approval this month send to those of the other European economic area countries EC type-approval authorities in the type-approval certificate, together with copy of the attachments specified in chapter C of annex 1;
9.3. the Centre shall forward each month to the rest of the European economic area, the EC type-approval authorities with a list of these rules specified in annex 5 the data for systems, components or separate technical units which it has given during that month, "or reference a type approval;
9.4. the Centre by other European economic area countries in the EC type-approval authority shall immediately forward the request to the appropriate components of a copy of the type-approval certificate and/or information package for which it is issued or refused withdrawn approval.

10. If the Center finds that a vehicle, system, component or separate technical unit may compromise traffic safety, human health, life or the environment, or do not meet all of the particulars in the information document, or is not passed all of the type approval certificate set out in the test, the Centre adopted a decision not to grant type approval and shall forthwith inform the rest of the European economic area, the EC type-approval authority and the European Commission.
11. Type-approval costs shall be borne by the applicant for type-approval.
12. If these rules or regulations on conformity assessment is amended and the type approval granted the Centre no longer complies with these rules or regulations for the assessment of conformity with the requirements, the Centre shall immediately inform the manufacturer.
13. further to this provision, the information referred to in paragraph 12, the manufacturer shall submit to the Center a month of submission of the type-approval of the amendment.
14. If the vehicle is changed (which granted type-approval) and the design is amended information package type: 14.1. the manufacturer of the vehicle together with the application for amendment shall be submitted to the Center in their part of the information package relating to the above changes, indicating the change and the serial number, starting with the changed constructs vehicles;
14.2. the amendment applied the appropriate amount in the Centre shall issue the revised pages of the information package, marking each revised page to clearly indicate the nature of the change and the date of re-issue;
14.3. the requirements laid down in this provision in paragraph 14.2. also, the information package in respect of the consolidated, updated version, for which a detailed description of the amendment;
14.4. whenever amended pages or a consolidated, updated version are issued, amended also the index to the information package attached to the approval certificate to indicate the last amendment date or the date of the consolidated, updated version;
14.5. the amendment shall be deemed to have a type extension. The Centre shall issue a revised EC type-approval certificate, which is the extended certificate number that clearly states the reason for the extension and its date of re-issue in the following cases: 14.5.1. If you need additional tests;
14.5.2. If any information in the EC type-approval certificate, with the exception of its attachments, has changed;
14.5.3. where the separate directives requirements that were in effect when the vehicle was prohibited in the original commissioning, is changed from the date shown on the vehicle EC type-approval certificate.
15. An application for amendment of a type-approval shall be submitted by the vehicle manufacturer in its European economic area countries in the EC type-approval authority which granted the original type-approval.
16. If the Center finds that need new or additional tests or checks to verify the conformity of the vehicle for road safety and environmental safety requirements, it shall inform the manufacturer of the vehicle. This provision gives centres mentioned in paragraph 14, the type-approval only after a successful test or inspection.
17. If the type-approval certificate is amended (assigned a new extended type approval and issuing the type-approval certificate) or a type-approved vehicle production stopped, within 30 working days of the Centre shall inform the other countries of the European economic area for the EC type-approval authority on the last vehicle, the serial number, which produce the vehicles according to the previously issued type-approval certificate and, where appropriate, the serial number with which started vehicle production under the amended certificate of type approval.
III. ensuring the conformity of production 18. Before granting type-approval, the EC type-approval authority, in cooperation with the EC type-approval authorities in the other Member States, to make sure that the manufacturer of this rule 6. the measures referred to in the annex and the procedures for the effective control of the production of vehicles or their components conform to the approved type of vehicle or component.
19. the type approval the manufacturer: 19.1. components of means of transport or their compliance with the approved vehicle or component type in the production process;
19.2. ensure the EC type-approval authority the availability of test equipment to be able to periodically check the production vehicles or components in conformity with the approved vehicle or component type;
19.3. ensure the registration of the test results and availability of EC type-approval authority, as well as coordination with the EC type-approval authority determines how long to store the test results;
19.4. constantly analyzes the test results to verify and ensure that the vehicle or component parameter stability;
19.5. perform repeat tests, if these provisions referred to in paragraph 20 of the sample or the sample sequence mismatch of vehicle or component type, as well as prevent flaws and restore the conformity to the approved type.
20. the EC type-approval authority in accordance with the selected periodic production surveillance procedure checks the compliance of vehicles or their components control methods and with random selection techniques select the samples conformity to approved vehicle or component type, check the manufacturer's laboratory or another manufacturer or the EC type-approval authority, selected testing laboratory.
21. the manufacturer shall provide EC type-approval authority the opportunity to take the vehicle and its components in the production process control.
IV. the recognition of type-approval and registration procedures in General is recognised in Latvia, 22:22.1. other European economic area countries assigned vehicles and their component type-approval, where a type-approval certificate issued in accordance with European Union legal requirements in the field of conformity assessment;
22.2. European economic area countries granted component type-approval of vehicles, if the type approval certificate issued in accordance with the relevant technical requirements of the regulations.

23. in other European economic area countries issued the type approval certificate for the vehicle shall be recognised in the following order: 23.1. the vehicle manufacturer shall provide to the Centre the application for type-approval-certificate of recognition. The application shall be accompanied by the following documents: 23.1.1. type approval certificate or a copy of it;
23.1.2. a vehicle or component type information document and picture or photo of the vehicle;
23.1.3. test lab reports or other documents required by the separate directives and refers to a type of vehicle;
23.1.4. certificate of conformity, the manufacturer shall certify that each specific vehicle to conform to the approved type;
23.2. the Centre within 10 working days of the appearance of the documents submitted and take a decision on the recognition of the type-approval certificate or the refusal of recognition. These rules 40 and 41 in the cases referred to in paragraph, Center on the recognition or withdrawal of recognition, as well as the decision on the number of vehicles shall be taken within three months.
24. If you have not submitted all the required documents, the Center shall inform the manufacturer of the vehicle, setting a deadline of 30 days for the submission of documents required, and the decision shall be taken after receipt of all required documents and review.
25. Other European economic area countries issued the type approval certificate for vehicles (excluding vehicle component type-approval certificate) in the center of their recognition.
26. the expenses for the type-approval certificate is borne by the producer and that submitted the rule 23.1. documents referred to.
V. certificate of conformity and the type-approval mark 27. the manufacturer of the vehicle type-approval holder – each individual made complete or incomplete vehicle in conformity with the approved vehicle type, issue a certificate of conformity in accordance with the provisions of annex 3.
28. the manufacturer each component or separate technical units produced in conformity with an approved type shall be accompanied by a trade name or mark, the type and the type approval mark, if it is required by the laws under which have been granted type-approval number in accordance with the requirements of this regulation.
29. If required, the manufacturer shall indicate in the certificate of conformity for detailed information about this rule 9.1. restrictions referred to and all conditions for the systems, components or separate technical units.
30. the vehicle manufacturer and their components kept in vehicles and component type approval documentation and ensure its availability to market surveillance authorities (at their request) for 10 years.
Vi. Trade conditions and market monitoring 31. market surveillance functions by the State Agency "State technical supervisory agency (hereinafter the Agency).
32. Permitted to distribute (sell, bestow, put into use against or without payment) or include a permanent register a vehicle if it is accompanied by a valid certificate of conformity, attesting that it conforms to an approved or recognized in Latvia of a type of vehicle. Completed vehicles not allowed to sell, but until their completion it is prohibited to include permanent registry and put into service.
33. Allowed to distribute or use components of a vehicle which is a type approval certificate or are labelled according to the requirements of the separate directives.
34. If the agency finds that the vehicle or component that has a certificate or mark of conformity do not conform to the approved type of the vehicle or its components, the Agency will inform the Center. This distribution of the vehicle, the registration or use, as well as the components of the vehicle distribution or use in Latvia is paused until the discrepancy is resolved.
35. the Centre within 30 working days of receipt of the information on non-conformity shall inform the manufacturer of the vehicle or its components and take the measures necessary to ensure that the vehicles, systems, components or separate technical units conform to the approved type (including asking the type approval authority which granted the type-approval to verify the fact of non-compliance).
36. If the agency finds that a vehicle, system, component or separate technical units accompanied by a certificate of conformity or the appropriate labelling, jeopardises road safety or occupational safety, it shall inform the Centre and for a period of not more than six months, prohibit in Latvia such a vehicle, system, component or separate technical unit sale, registration and entry into service. The Centre shall immediately inform the other European economic area countries EC type-approval authority and the European Commission in support of the ban.
37. If the Center finds that a vehicle, system, component or separate technical unit type-approval granted by the Centre, jeopardises road safety, human health, life, environment, or does not comply with all the relevant data listed in the information package, the Center shall withdraw approval. Center 30 working days notify the other countries of the European economic area in the EC type-approval authorities and the European Commission of any withdrawal of type-approval, giving reasons for its decision.
VII. Exemptions and incentives that provision 38.32. the requirements referred to in paragraph 1 shall not apply to vehicles intended for use in the armed forces, civil protection, fire-fighting or public order maintenance services, and to vehicles type-approved in accordance with the provisions of paragraph 39.
39. At the request of the manufacturer, the EC type-approval authority, based on expert opinion, these rules can be released 40 and 41 vehicles referred to in points from one or more of the technical requirements of the separate directives, if it does not affect the safety of vehicles and do not change their functionality. Each year, the EC type-approval authority shall send to the European Commission and other European economic area countries a list of exemptions granted.

40. the EC type-approval authority based on the manufacturer's request, be permitted to sell, register or put into service in a small series manufactured vehicles, if these rules are followed in part A of annex 7 to the quantitative limits referred to in. EC type-approval authority shall each year send the Commission produced in small series type approval of the vehicle. If small series vehicles type-approved in Latvia, the Centre sends the member specified by the manufacturer of the EC type-approval authorities in the information document, the EC type-approval certificate and copies of all attachments, stating the nature of the exemptions granted.
41. the EC type-approval authority based on the manufacturer's request, a limited period of time (at one stage finished vehicles-to 24 months, and finished vehicles, up to 30 months from the approval date) permits the sale, registration or entry into service of new vehicles of the end of the series, if they conform to the vehicle type for which approval is no longer valid, subject to this provision 7. in part B of the annex, these limits if the following conditions are met : 25.5. these vehicles are located in the European economic area country and have a certificate of conformity issued when the type-approval of the vehicle in question was still valid, but the vehicle was not registered or placed in service;
41.2. the manufacturer shall submit a reasoned request of any EC type-approval authorities affecting those vehicle types commissioning, specifying the request technical and/or economic reasons;
41.3. all Member States concerned to the following types of vehicle the commissioning is responsible for ensuring that the manufacturer complies with the annex 7 part B requirements.
VIII. Non-compliance and non-compliance with the type 42. Vehicles, systems, components or separate technical units which, in the light of technological advances, designed in accordance with techniques or principles that are incompatible with one or more of the separate directives or requirements, EC type-approval authority granting temporary approval. In this case, it shall within one month send to the rest of the European economic area, the EC type-approval authorities and the European Commission in the type approval certificate and its annexes, as well as a request to allow the European Commission to grant type-approval. The request shall be accompanied by the following information: 42.1. the reasons for which the techniques or principles at issue make the vehicle, system, component or separate technical unit incompatible with the requirements of one or more of the separate directives;
26.2. safety, environmental protection or safety problems and their solution description;
26.3. the tests and their results, which show that a vehicle, system, component or separate technical unit at least equivalent guarantees of safety, environmental protection and safety in one or more of the requirements of the directives.
43. If the request is accepted, the European Commission, EC type-approval authority granting type-approval in accordance with these rules. This type of period of validity of the approval shall not be less than 36 months.
44. If the rules referred to in annex 1. separate directive are adapted to technical progress in accordance with these provisions and 42 and 43 in approved vehicles, systems, components or separate technical units comply with the grozītaj therefore the separate directives, the EC type-approval authority shall issue a new type-approvals which comply with these rules. If the separate directive are not adjusted, the EC type-approval authority that granted the EC type-approval, shall submit a request to the European Commission, and the EC type-approval of extended validity only upon acceptance by the European Commission.
45. the vehicle does not conform to the approved type, if a discrepancy is found, type-approval certificate or the information package and if such discrepancies are not permitted by the European economic area country, which has granted the type approval. A vehicle is deemed to conform to the approved type where tolerances are met, where the rules referred to in annex 1 of the separate directives.
46. the Centre shall inform the EC type-approval authority which granted the system, component, separate technical unit or incomplete vehicle type-approval, to ensure that vehicles in production conform to the approved type where: 46.1. has the vehicle type-approval where non-conformity of the vehicle type occurs only systems, components or separate technical unit;
46.2. "multi-stage type-approval where non-conformity of the vehicle occurs only systems, components or separate technical unit which is part of the incomplete vehicle, or of the incomplete vehicle itself.
47. the Centre for this rule 46 of the cases referred to in paragraph shall immediately inform the European Commission and take this provision 35. measures referred to in paragraph 1.
48. This provision 46. in the cases referred to in paragraph 1 the manufacturer fixes flaws and restore the conformity to the approved type. The Centre will inform the other European economic area countries of the EC type-approval authority.
Notification of Decision x and appeals 49. Center decision concerning type-approval refusal or revocation shall be notified in writing to the manufacturer.
50. the Centre's decision may be challenged in the Ministry of the economy.
X. closing questions 51. Be declared unenforceable in the Cabinet of 19 April 2005, regulations No. 277 "agricultural or forestry tractor, trailers, interchangeable towed machinery and its components conformity assessment rules" (Latvian journal, 2005, nr. 78).
52. provisions applicable to the July 1, 2006.
53. these provisions are published the rules of the directive, carried by a reference to those provisions. 
Informative reference to European Union directives, the regulations include provisions resulting from: 1) Parliament and of the Council of 26 May 2003 of Directive 2003/37/EC relating to the type-approval of agricultural or forestry tractors, their trailers and interchangeable towed machinery, together with their systems, components and separate technical units and repealing Directive 74/150/EEC;

2) Council of 26 April 2004, Directive 2004/66/EC of the European Parliament and Council Directive 1999/45/EC, 2002/83/EC, 2003/37/EC and 2003/59/EC, and Council Directive 77/388/EEC, 91/414/EEC, 96/26/EC, 2003/48/EC and 2003/49/EC adapted to the free movement of goods, freedom to provide services, agriculture, transport and tax policies with regard to the Czech Republic Estonia, Cyprus, Latvia, Lithuania, Hungary, Malta, Poland, Slovenia and Slovakia to the European Union;
3) Council of 4 March 1974 to Directive 74/151/EEC on the approximation of the laws of the Member States relating to certain parts and characteristics of wheeled agricultural or forestry tractors;
4) Council of 4 March 1974 to Directive 74/152/EEC on the approximation of the laws of the Member States relating to wheeled agricultural or forestry tractors to the maximum design speed and load platforms;
5) Council of 25 June 1974 Directive 74/346/EEC on the approximation of the laws of the Member States relating to rear-view mirrors for wheeled agricultural or forestry tractors;
6) Council of 25 June 1974 Directive 74/347/EEC on the approximation of the laws of the Member States relating to wheeled agricultural or forestry tractors field of vision and windscreen wipers;
7) Council of 20 May 1975 Directive 75/321/EEC on the approximation of the laws of the Member States relating to the steering equipment of wheeled agricultural or forestry tractors;
8) Council of 20 May 1975 Directive 75/322/EEC on the approximation of the laws of the Member States relating to wheeled agricultural or forestry tractors to the Suppression of radio interference produced by spark-ignition engines fitted;
9) Council of 6 April 1976 Directive 76/432/EEC on the approximation of the laws of the Member States relating to the braking devices of wheeled agricultural or forestry tractors;
10) Council of 27 July 1976 Directive 76/763/EEC on the approximation of the laws of the Member States relating to passenger seats for wheeled agricultural or forestry tractors;
11) Council of 29 March 1977 Directive 77/311/EEC on the approximation of the laws of the Member States relating to the noise level of wheeled agricultural or forestry tractors leaders;
12) Council of 28 June 1977 Directive 77/536/EEC on the approximation of the laws of the Member States relating to the roll-over protection structures of wheeled agricultural or forestry tractors;
13 1978) 25 July to Directive 78/764/EEC on the approximation of the laws of the Member States relating to the driver's seat on wheeled agricultural or forestry tractors;
14) Council of 17 October 1978 in Directive 78/933/EEC on the approximation of the laws of the Member States relating to the installation of lighting and light-signalling devices on wheeled agricultural and forestry tractors;
15) Council may 17, 1979 by Directive 79/532/EEC on the approximation of the laws of the Member States relating to the component type-approval of lighting and light-signalling devices on wheeled agricultural and forestry tractors;
16) Council may 17, 1979 by Directive 79/533/EEC on the approximation of the laws of the Member States relating to wheeled agricultural or forestry tractors to the coupling device and the reverse;
17) Council of 25 June 1979 by Directive 79/622/EEC on the approximation of the laws of the Member States relating to the roll-over protection structures of wheeled agricultural or forestry tractors (static testing);
18) Council of 24 June 1980 of Directive 80/720/EEC on the approximation of the laws of the Member States relating to the operating space, access to the driving position and the doors and Windows of wheeled agricultural and forestry tractors;
19) Council of 26 May 1986 Directive 86/297/EEC on the approximation of the laws of the Member States relating to agricultural and forestry tractor power take-off and its protection;
20) Council of 26 May 1986 Directive 86/298/EEC on rear-mounted roll-over protection structures of narrow-track wheeled agricultural and forestry tractors;
21) Council of 24 July 1986 Directive 86/415/EEC on agricultural and forestry tractors installation, location, operation and identification of controls;
22) Council of 25 June 1987 directives 87/402/EEC on narrow-track wheeled agricultural and forestry tractors roll-over protection structures mounted in front of the driver's seat;
23) Council of 21 December 1988, Directive 89/173/EEC on the approximation of the laws of the Member States relating to certain components and characteristics of wheeled agricultural or forestry tractors;
24) of the European Parliament and of the Council of 22 May 2000 Directive 2000/25/EC, on action to be taken against the emission of gaseous and particulate pollutants by engines intended to power agricultural or forestry tractors and amending Council Directive 74/150/EEC;
25) Commission of 21 February 2005 Directive 2005/13/EC of the European Parliament and the Council amending Directive 2000/25/EC in relation to emission of gaseous and particulate pollutants by engines intended to power agricultural or forestry tractors, and amending Annex I to the directive of the European Parliament and of the Council 2003/37/EC relating to the type-approval of agricultural or forestry tractors;
26) Commission of 18 October 2005 Directive 2005/67/EC amending Council Directive 86/298/EEC, annexes I and II to Council Directive 87/402/EEC and annexes I and II to the directive of the European Parliament and of the Council 2003/37/EC annex I, II and III in relation to the agricultural or forestry tractor type-approval, to be adapted;
27) Council of 17 December 1982 of Directive 82/890/EEC amending the directives on the approximation of the laws of the Member States relating to wheeled agricultural or forestry tractors;
28) Commission of 21 June 1988 Directive 88/410/EEC adapting to technical progress Council Directive 74/151/EEC on the approximation of the laws of the Member States relating to certain parts and characteristics of wheeled agricultural or forestry tractors;
29) Commission of 3 June 1998 Directive 98/38/EC adapting to technical progress Council Directive 74/151/EEC with respect to certain agricultural and forestry tractors parts and parameters;

30) of the European Parliament and of the Council of 23 September 1997 Directive 97/54/EC relating to agricultural or forestry tractors to the maximum design speed of amending Council directives 74/150/EEC, 74/151/EEC, 74/152/EEC, 74/346/EEC, 74/347/EEC, 75/321/EEC, 75/322/EEC, 76/432/EEC, 76/763/EEC, 77/311/EEC, 77/537/EEC, 78/764/EEC , 78/933/EEC, 79/532/EEC, 79/533/EEC, 80/720/EEC, 86/297/EEC, 86/415/EEC and 89/173/EEC;
31) Commission of 22 June 1988 Directive 88/412/EEC adapting to technical progress Council Directive 74/152/EEC on the approximation of the laws of the Member States relating to wheeled agricultural or forestry tractors to the maximum design speed and load platforms;
32) Commission of 21 June 1988 Directive 88/411/EEC adapting to technical progress Council Directive 75/321/EEC on the approximation of the laws of the Member States relating to the steering equipment of wheeled agricultural or forestry tractors;
33) Commission of 22 June 1988 Directive 88/413/EEC adapting to technical progress Council Directive 79/622/EEC on the approximation of the laws of the Member States relating to the roll-over protection structures of wheeled agricultural or forestry tractors (static testing);
34) Commission of 22 June 1988 Directive 88/414/EEC adapting to technical progress Council Directive 80/720/EEC on the approximation of the laws of the Member States relating to the operating space, access to the driving position and the doors and Windows of wheeled agricultural and forestry tractors;
35) Commission 30 June 1988 Directive 88/465/EEC adapting to technical progress Council Directive 78/764/EEC on the approximation of the laws of the Member States relating to the driver's seat on wheeled agricultural or forestry tractors;
36) Council of 21 December 1989 directive 89/680/EEC amending Directive 77/536/EEC on the approximation of the laws of the Member States relating to the roll-over protection structures of wheeled agricultural or forestry tractors;
37) Council of 21 December 1989 directive 89/681/EEC amending Directive 87/402/EEC on narrow-track wheeled agricultural and forestry tractors roll-over protection structures mounted in front of the driver's seat;
38) Council of 21 December 1989 directive 89/682/EEC, amending Directive 86/298/EEC on rear-mounted roll-over protection structures of narrow-track wheeled agricultural and forestry tractors;
39) Commission of 22 November 1979 by Directive 79/1073/EEC adapting to technical progress Council Directive 74/347/EEC on the approximation of the laws of the Member States relating to wheeled agricultural or forestry tractors field of vision and windscreen wipers;
40) Council of 25 June 1987 directives 87/354/EEC, amending certain directives on the approximation of the laws of the Member States relating to industrial products with respect to the distinctive numbers and letters indicating the Member States;
41) Commission of 15 December 1982 of Directive 82/953/EEC adapting to technical progress Council Directive 79/622/EEC on the approximation of the laws of the Member States relating to the roll-over protection structures of wheeled agricultural or forestry tractors (static testing);
42) Commission 28 March 1983 Directive 83/190/EEC adapting to technical progress Council Directive 78/764/EEC on the approximation of the laws of the Member States relating to the driver's seat on wheeled agricultural or forestry tractors;
43) Commission of 30 September 1996, Directive 96/63/EC amending Council Directive 76/432/EEC on the approximation of the laws of the Member States relating to the braking devices of wheeled agricultural or forestry tractors;
44) Commission 5 June 1998 Directive 98/39/EC, adapting to technical progress Council Directive 75/321/EEC relating to the steering equipment of wheeled agricultural or forestry tractors;
45) Commission of 8 June 1998 Directive 98/40/EC adapting to technical progress Council Directive 74/346/EEC relating to rear-view mirrors for wheeled agricultural or forestry tractors;
46) Commission 20 November 1998 Directive 98/89/EC adapting to technical progress Council Directive 74/152/EEC relating to wheeled agricultural or forestry tractors on the maximum design speed and load platforms;
47) Commission of 6 May 1999 Directive 1999/40/EC, adapting to technical progress Council Directive 79/622/EEC on the approximation of the laws of the Member States relating to the roll-over protection structures of wheeled agricultural or forestry tractors (static testing);
48) the Commission's 1 June 1999 Directive 1999/55/EC adapting to technical progress Council Directive 77/536/EEC relating to the roll-over protection structures of wheeled agricultural or forestry tractors;
49) Commission of 3 June 1999, Directive 1999/56/EC adapting to technical progress Council Directive 78/933/EEC relating to the installation of lighting and light-signalling devices on wheeled agricultural and forestry tractors;
50) Commission of 7 June 1999, Directive 1999/57/EC adapting to technical progress Council Directive 78/764/EEC relating to the driver's seat on wheeled agricultural or forestry tractors;
51) Commission of 7 June 1999, Directive 1999/58/EC adapting to technical progress Council Directive 79/533/EEC relating to coupling and reversing devices for wheeled agricultural or forestry tractors;
52) Council of 11 November 1999 Directive 1999/86/EC adapting to technical progress Directive 76/763/EEC on the approximation of the laws of the Member States relating to passenger seats for wheeled agricultural or forestry tractors;
53) Commission of 13 April 2000, Directive 2000/19/EC adapting to technical progress Council Directive 86/298/EEC on rear-mounted roll-over protection structures of narrow-track wheeled agricultural and forestry tractors;
54) Commission of 28 April 2000, Directive 2000/22/EC adapting to technical progress Council Directive 87/402/EEC on narrow-track wheeled agricultural and forestry tractors roll-over protection structures mounted in front of the driver's seat;
55) Commission of 14 January 2000, Directive 2000/1/EC adapting to technical progress Council Directive 89/173/EEC on the approximation of the laws of the Member States relating to certain components and characteristics of wheeled agricultural or forestry tractors;

56) Commission of 14 January 2000, Directive 2000/2/EC, adapting to technical progress Council Directive 75/322/EEC relating to the Suppression of radio interference produced by spark-ignition engines fitted to wheeled agricultural or forestry tractors and Council Directive 74/150/EEC relating to wheeled agricultural or forestry tractors type approval;
57) Commission of 8 January 2001, Directive 2001/3/EC adapting to technical progress Council Directive 74/150/EEC relating to the type-approval of wheeled agricultural or forestry tractors and Council Directive 75/322/EEC relating to wheeled agricultural or forestry tractors to the Suppression of radio interference produced by spark-ignition engines fitted;
58) Council of 28 June 1977 Directive 77/537/EEC on the approximation of the laws of the Member States relating to the measures to be taken against the emission of pollutants from diesel engines for use in wheeled agricultural or forestry tractors.
Prime Minister a. Halloween Minister of Agriculture m. Roze Editorial Note: rules applicable to 1 July 2006.
The provisions of the directive-European Union law database http:////eur-URlex.europa.eu en URindex.htm Ministry of Agriculture presented version of annex 1 of the Cabinet of Ministers of 27 June 2006 regulations no 535 vehicle categories definitions and requirements for EC type-approval for A vehicle section categories and vehicle types a. definition of vehicle category definition 1. T category: tractors: 1.1 category T1: wheeled tractors for which the maximum design speed of not more than 40 km/h the minimum distance between the wheels to the axis closest to the driver (tractors with reversible driving position (reversible seat and steering wheel) for the driver to the nearest axis must be considered as axis, equipped with the biggest diameter tyres) of not less than 1150 mm, with an unladen mass, in running order, of more than 600 kg and not exceeding 1000 mm clearance; 1.2. category T2: wheeled tractors of which the maximum design speed of not more than 40 km/h the minimum distance between the wheels is less than 1150 mm, mass in running order, of more than 600 kg and not exceeding 600 mm ground clearance. If the height of the Centre of gravity of the tractor (measured in relation to the ground) to the average minimum distance between the wheels of each axle exceeds 0.90 to, the maximum design speed is limited to 30 km/h;
1.3. Category T3: wheeled tractors of which the maximum design speed of not more than 40 km/h and an unladen mass, in running order, of not more than 600 kg;
1.4. Category T4: special wheeled tractors for which the maximum design speed of not more than 40 km/h (according to Appendix 1);
1.5. Category T5: wheeled tractors with a maximum design speed of more than 40 km/h. 2. C category: crawler tractor that axle and steering are endless. C1 through C5 category similar to T1 to T5 category, as defined in this chapter A of the annex, part A, point 1.
3. R: trailers: 3.1 category R1: trailers, which the sum of the technically permissible masses per axle of which does not exceed 1500 kg;
3.2. R2: trailers for which the sum of the technically permissible masses per axle exceeds 1500 kg but does not exceed 3500 kg;
3.3. category R3: trailers for which the sum of the technically permissible masses per axle exceeds 3500 kg but does not exceed 21000 kg;
3.4. the R4: trailers, which the sum of the technically permissible masses per axle of which exceeds 21000 kg.
3.5. each category of trailers, according to its design speed also includes an "a" or "b" index: "a" 3.5.1 – trailers with a maximum design speed of 40 km/h or less;
3.5.2. "b" for trailers with a maximum design speed exceeding 40 km/h. Rb3 is a category of trailers for which the sum of the technically permissible masses per axle exceeds 3500 kg but does not exceed 21000 kg, and designed to be towed by a tractor in category T5.
4. S category: interchangeable towed machinery: 4.1 category S1: interchangeable towed machinery intended for agricultural or forestry use and which the sum of the technically permissible masses per axle of which does not exceed 3500 kg;
4.2. S2: interchangeable towed machinery for use in agriculture or forestry and which the sum of the technically permissible masses per axle exceeds 3500 kg;
4.3. for each category of interchangeable towed machinery according to its design speed also includes an "a" or "b" index: 4.3.1. "a" – interchangeable towed machinery with a maximum design speed of 40 km/h or less;
4.3.2. "b" for interchangeable towed machinery with a maximum design speed of more than 40 km/h. example. Sb2 is a category of interchangeable towed machinery for which the sum of the technically permissible masses per axle exceeds 3500 kg and designed to be towed by a tractor in category T5.
B. definition of vehicle type 1. Wheeled tractors: 1.1. "type" means tractors of the same category that do not differ in respect of at least the following basic: 1.1.1. manufacturer;
1.1.2. the manufacturer's type designation;
1.1.3. the main construction characteristics and design of basic parameters: 1.1.3.1. backbone chassis/chassis with side members/articulated chassis (obvious and fundamental differences);
1.1.3.2. engine (internal combustion/electric/hybrid);
1.1.3.3. axles (number);
1.2. the "variant" means tractors of the same type which do not differ in respect of at least the following: 1.2.1 the main engine: 1.2.1.1. working principle;
1.2.1.2. number and arrangement of cylinders;
1.2.1.3 capacity difference of no more than 30% (the largest being no more than 1.3 times the lowest);
1.2.1.4. volumetric difference of no more than 20% (the highest is more than 1.2 times not greater than the smallest);
1.2.2. powered axles (number, position, interconnection);
1.2.3. the steered axles (number and position);
1.2.4. maximum laden mass does not differ by more than 10%;
1.2.5. the transmission (type);
1.2.6. the roll-over protection structure;
1.2.7. braked axles (number);
1.2.8. "variation version" means tractors which consist of a combination of the subject matter, which in accordance with the provisions of the annex appearing in the information package.
2. Track-laying tractors: idem wheeled tractors, as defined in this chapter A of the annex, part B, point 1.
3. Trailer: 3.1 "type" means a category of trailers, which do not differ in respect of at least the following basic: 3.1.1. manufacturer;
3.1.2. the manufacturer's type designation;

3.1.3. main construction characteristics and design of basic parameters: 3.1.3.1. backbone chassis/chassis with side members/articulated chassis (obvious and fundamental differences);
3.1.3.2. axles (number);
3.2. the "variant" means trailers of the same type which do not differ in respect of at least the following characteristics: 3.2.1. steered axles (number, position, interconnection);
3.2.2. maximum laden mass does not differ by more than 10%;
3.2.3. braked axles (number).
4. Interchangeable towed machinery: idem trailers as defined in this chapter A of the annex, part B, paragraph 3.
 
(B) the Department of Vehicle EC type-approval part I of the list of requirements in separate directives No.
 Subject to annex the base directive and the full name of the directive and in the official journal of the European Union publication data applicability (T4 and C4-Appendix 1) Tl T2 T3 T5 C R S 1.1.
 Maximum laden mass 74/151/EEC of the Council of 4 March 1974 Directive 74/151/EEC on the approximation of the laws of the Member States relating to certain parts and characteristics of wheeled agricultural or forestry tractors (84, 28.3.1974, p. 25) X X X X (X) (X) (X) 1.2.
 Number plate 74/151/EEC of the Council of 4 March 1974 Directive 74/151/EEC on the approximation of the laws of the Member States relating to certain parts and characteristics of wheeled agricultural or forestry tractors (84, 28.3.1974, p. 25) X X X X I (X) (X) 1.3.
 Fuel tank 74/151/EEC of the Council of 4 March 1974 Directive 74/151/EEC on the approximation of the laws of the Member States relating to certain parts and characteristics of wheeled agricultural or forestry tractors (84, 28.3.1974, p. 25) X X X X I — — 1.4.
 The ballast masses 74/151/EEC (IV) Council of 4 March 1974 Directive 74/151/EEC on the approximation of the laws of the Member States relating to certain parts and characteristics of wheeled agricultural or forestry tractors (84, 28.3.1974, p. 25) X X (X) (I) — — 1.5.
 Audible warning device 74/151/EEC V Council 4 March 1974 Directive 74/151/EEC on the approximation of the laws of the Member States relating to certain parts and characteristics of wheeled agricultural or forestry tractors (84, 28.3.1974, p. 25) X X X X I — — 1.6.
 Sound level (external) 74/151/EEC the Council VI, 4 March 1974 Directive 74/151/EEC on the approximation of the laws of the Member States relating to certain parts and characteristics of wheeled agricultural or forestry tractors (84, 28.3.1974, p. 25) X X X (X) (I) — — 2.1.
 The maximum speed of 74/152/EEC annex 1 of the Council of 4 March 1974 Directive 74/152/EEC on the approximation of the laws of the Member States relating to wheeled agricultural or forestry tractors to the maximum design speed and load platforms (84, 28.3.1974, p. 33) X X X (X) (I) — — 2.2.
 Cargo platform 74/152/EEC of the Council of 4 March 1974 Directive 74/152/EEC on the approximation of the laws of the Member States relating to wheeled agricultural or forestry tractors to the maximum design speed and load platforms (84, 28.3.1974, p. 33) X X X (X) (I) — — 3.1.
 Rear-view mirrors, 74/346/EEC of the Council of 25 June 1974 Directive 74/346/EEC on the approximation of the laws of the Member States relating to rear-view mirrors for wheeled agricultural or forestry tractors (191, 15.7.1974, p. 1) X X (X) (I) — — 4.1.
 Area of vision and windscreen wipers 74/347/EEC of the Council of 25 June 1974 Directive 74/347/EEC on the approximation of the laws of the Member States relating to wheeled agricultural or forestry tractors field of vision and windscreen wipers (191, 15.7.1974, p. 5) X X X (X) (I) — — 5.1.
 The steering system 75/321/EEC of the Council of 20 May 1975 Directive 75/321/EEC on the approximation of the laws of the Member States relating to the steering equipment of wheeled agricultural or forestry tractors (147, 9.6.1975, p. 24) X X X (X) (X):-6.1.
 Electromagnetic compatibility 75/322/EEC of the Council of 20 May 1975 Directive 75/322/EEC on the approximation of the laws of the Member States relating to wheeled agricultural or forestry tractors to the Suppression of radio interference produced by spark-ignition engines fitted (147, 9.6.1975, p. 28) X X X X I — — 7.1.
Braking devices 76/432/EEC of the Council of 6 April 1976 Directive 76/432/EEC on the approximation of the laws of the Member States relating to the braking devices of wheeled agricultural or forestry tractors (122, 8.5.1976, p. 1) — X X X (X) (X) (X) 71/320/EEC (4) of the Council of 26 July 1971 the Directive 71/320/EEC on the approximation of the laws of the Member States of certain categories of motor vehicles and their trailers (202 of the braking equipment , 6.9.1971, p. 1. 37)
 —
 —
 —
 X
 —
 —
 —
 8.1.
 Passenger seats on Council 76/763/EEC of 27 July 1976 Directive 76/763/EEC on the approximation of the laws of the Member States relating to passenger seats for wheeled agricultural or forestry tractors (262, 27.9.76, p. 135) X — X (X) (I) — — 9.1.
 Sound level (internal), 77/311/EEC of the Council of 29 March 1977 Directive 77/311/EEC on the approximation of the laws of the Member States relating to the noise level of wheeled agricultural or forestry tractors leaders (105, 28/04/1977, p. 1) X X X (X) (I) — — 10.1.
 Roll-over protection structures of Council 77/536/EEC of 28 June 1977 Directive 77/536/EEC on the approximation of the laws of the Member States relating to the roll-over protection structures of wheeled agricultural or forestry tractors (220, 29.8.1977, p. 1) — X (X) (X) — — 11.1.
 Measures of contaminants in diesel emissions Council 77/537/EEC of 28 June 1977 Directive 77/537/EEC on the approximation of the laws of the Member States relating to the measures to be taken against the emission of pollutants from diesel engines for use in wheeled agricultural or forestry tractors X X X X X 12.1.
 The driving position 78/764/EEC

Council of 25 July 1978 by Directive 78/764/EEC on the approximation of the laws of the Member States relating to the driver's seat on wheeled agricultural or forestry tractors (255, 18.9.1978, p. 1) X X X (X) (X):-13.1.
 Lighting installation of 78/933/EEC Council of 17 October 1978 in Directive 78/933/EEC on the approximation of the laws of the Member States relating to the installation of lighting and light-signalling devices on wheeled agricultural and forestry tractors (325, 20.11.1978, p. 16) X X X (X) (X) (X) (I) 14.1.
 Lights and warning devices 79/532/EEC of the Council of 17 May 1979 by Directive 79/532/EEC on the approximation of the laws of the Member States relating to the component type-approval of lighting and light-signalling devices on wheeled agricultural and forestry tractors (145, 13.6.1979, p. 16) X X X X X (X) (X) 15.1.
 Coupling and reversiekārt 79/533/EEC of the Council of 17 May 1979 by Directive 79/533/EEC on the approximation of the laws of the Member States relating to wheeled agricultural or forestry tractors to the coupling device and the reverse of (145, 13.6.1979, p. 20) X X X (X) (I) — — 10.0.
 ROPS (static testing) 79/622/EEC of the Council of 25 June 1979 by Directive 79/622/EEC on the approximation of the laws of the Member States relating to the roll-over protection structures of wheeled agricultural or forestry tractors (static testing) (179, 17.7.1979, p. 1) X (X) (I) — — — — 17.1.
 The operating space, access to the driving position of 80/720/EEC of the Council of 24 June 1980 of Directive 80/720/EEC on the approximation of the laws of the Member States relating to the operating space, access to the driving position and the doors and Windows of wheeled agricultural and forestry tractors (194, 28.7.1980, p. 1) — X X (X) (I) — — 18.1.
 PTO 86/297/EEC of the Council of 26 May 1986 Directive 86/297/EEC on the approximation of the laws of the Member States relating to agricultural and forestry tractor power take-off and its protection (186, 8.7.1986, p. 19) X X X (X) (I) — — 19.1.
 Rear mounted ROPS (narrow-track wheeled tractors) 86/298/EEC of the Council of 26 May 1986 Directive 86/298/EEC on rear-mounted roll-over protection structures of narrow-track wheeled agricultural and forestry tractors (186, 8.7.1986, p. 26)-X-(X) (I) — — 20.1.
 Installing controls 86/415/EEC of the Council of 24 July 1986 Directive 86/415/EEC on agricultural and forestry tractors installation, location, operation and identification of controls (240, 26.8.1986, p. 1) X X X (X) (I) — — 21.1.
 Front mounted ROPS (narrow-track wheeled tractors) 87/402/EEC of the Council of 25 June 1987 Directive 87/402/EEC on narrow-track wheeled agricultural and forestry tractors roll-over protection structures mounted in front of the driver's seat (220, 8.8.1987, p. 1)-X-(X) (I) — — 22.1.
 Size and mass of the trailer I 89/173/EEC of the Council of 21 December 1988, Directive 89/173/EEC on the approximation of the laws of the Member States relating to certain components and characteristics of wheeled agricultural or forestry tractors (67, 10.3.1989, p. 1) X X X (X) (X) (X) (I) 22.2.
Glass 89/173/EEC III Council of 21 December 1988, Directive 89/173/EEC on the approximation of the laws of the Member States relating to certain components and characteristics of wheeled agricultural or forestry tractors (67, 10.3.1989, p. 1) — I — — X X X 92/22/EEC (4) of the Council of 31 March 1992 Directive 92/22/EEC relating to motor vehicles and their trailers on safety glazing and glazing materials (129 , 14.5.1992, p. 1. 11)
 —
 —
 —
 X
 —
 —
 —
 22.3.
 Speed regulator 89/173/EEC, II (1) a Council of 21 December 1988, Directive 89/173/EEC on the approximation of the laws of the Member States relating to certain components and characteristics of wheeled agricultural or forestry tractors (67, 10.3.1989, p. 1) X X X (X) (I) — — 22.4.
 Drive components protection 89/173/EEC, II 2 Council of 21 December 1988 Directive 89/173/EEC on the approximation of the laws of the Member States relating to certain components and characteristics of wheeled agricultural or forestry tractors (67, 10.3.1989, p. 1) X X X (X) (I) — — 22.5.
 The mechanical coupling device 89/173/EEC (IV) Council of 21 December 1988, Directive 89/173/EEC on the approximation of the laws of the Member States relating to certain components and characteristics of wheeled agricultural or forestry tractors (67, 10.3.1989, p. 1) X X X (X) (X) (X) (I) 22.6.
 Required manufacturer's plate 89/173/EEC V Council of 21 December 1988, Directive 89/173/EEC on the approximation of the laws of the Member States relating to certain components and characteristics of wheeled agricultural or forestry tractors (67, 10.3.1989, p. 1) X X X (X) (X) (X) (I) 14.1.
 Trailer brake transmission 89/173/EEC the Council VI, 21 December 1988 of Directive 89/173/EEC on the approximation of the laws of the Member States relating to certain components and characteristics of wheeled agricultural or forestry tractors (67, 10.3.1989, p. 1) X X X (X) (X) (X) (I) 23.1.
 Pollutant emissions 2000/25/EC of the European Parliament and of the Council of 22 May 2000 Directive 2000/25/EC, on action to be taken against the emission of gaseous and particulate pollutants by engines intended to power agricultural or forestry tractors and amending Council Directive 74/150/EEC (173, 12.7.2000, p. 1) X X X X X — — 24.1.
 […/…/EC] Riepas1 — X X X — X (X) (X) 31.
 […/…/EC] Stabilitāte1 — — — — — — — SD 26.1.
 Belt stiprinājumi3 76/115/EEC (4) of the Council of 18 December 1975 Directive 76/115/EEC on the approximation of the laws of the Member States relating to anchorages for motor-vehicle safety belts (24, 30.1.1976, p. 6) X X X X X — — 27.1.
 Safety belts 77/541/EEC (4)

Council of 27 June 1977 Directive 77/541/EEC on the approximation of the laws of the Member States relating to safety belts and restraint systems of motor vehicles (220, 29.8.1977, p. 95) — — — — — — X 28.1.
 Reverse and speedometer 75/443/EEC (4) of the Council of 26 June 1975 Directive 75/443/EEC on the approximation of the laws of the Member States relating to the reverse and speedometer equipment of motor vehicles (196, 26.7.1975, p. 1) — — — — — — X 29.1.
 Spray-suppression devices 91/226/EEC (4) of the Council of 27 March 1991 Directive 91/226/EEC on the approximation of the laws of the Member States relating to the spray-suppression systems of certain categories of motor vehicles and their trailers (103, 23.4.1991, p. 5) — — — — X (X): 30.1.
 Speed limiters 92/24/EEC (4) of the Council of 31 March 1992 Directive 92/24/EEC relating to speed limitation devices or similar speed limitation on-board systems of certain categories of motor vehicles (129, 14.5.1992, p. 154) — — — — — — X 31.1.
 Rear security konstrukcijas1 […/…/EC] — — — — — — — SD 32.1.
Lateral protection 89/297/EEC (4) of the Council of 13 April 1989 directive 89/297/EEC on the approximation of the laws of the Member States relating to certain motor vehicles and their trailers to the lateral protection (side guards) (124, 5.5.1989) — — — — — X (X) notation.
X-apply fully.
(X)-apply grozītu2.
SD-a separate directive.
– do not apply.
I – like T according to category.
 The notes.
1 pending the adoption of directives on tyres, stability and rear safety structures, the fact that individual directives, shall not prevent the grant whole-vehicle type approval.
2 granting type-approval, the brackets are not used.
3 T1, T2, T3, C1, C2 and C3 of the tractors category minimum number of belt anchorages are two as N3 vehicles forward facing seats, medium defined by Directive 76/115/EEC, annex I, Appendix I. The following categories of tractor test load shall be applied to vehicles of category N3 to the said directive set out in annex I and in point 5.4.3.5.4.4..
4 here is the framework directive on motor vehicles number, they must follow the requirements in the light of EC type-approval in force on the date of the latest amendment to the specified in the law on conformity assessment of motor vehicles.
 
 
Separate directive amendments p.k.
Individual directive amended directive name Full OJ L 1.
74/151/EEC, 82/890/EEC of the Council of 17 December 1982 Directive 82/890/EEC amending the directives on the approximation of the laws of the Member States relating to agricultural and forestry tractors 378, 31.12.1982, p. 45 88/410/EEC of the Commission of 21 June 1988, Directive 88/410/EEC adapting to technical progress Council Directive 74/151/EEC on the approximation of the laws of the Member States relating to certain parts and characteristics of wheeled agricultural or forestry tractors 200 , 26.7.1988, p. 27 97/54/EC of the European Parliament and of the Council of 23 September 1997 Directive 97/54/EC as regards the agricultural and forestry tractors to the maximum design speed of amending Council Directive 74/150/EEC, 74/151/EEC, 74/152/EEC, 74/346/EEC, 74/347/EEC, 75/321/EEC, 75/322/EEC, 76/432/EEC, 76/763/EEC, 77/311/EEC , 77/537/EEC, 78/764/EEC, 78/933/EEC, 79/532/EEC, 79/533/EEC, 80/720/EEC, 86/297/EEC, 86/415/EEC and 89/173/EEC 277 10.10.1997 p. 24.98/38/EC of the Commission of 3 June 1998 Directive 98/38/EC adapting to technical progress Council Directive 74/151/EEC with respect to certain agricultural and forestry tractors parts and characteristics of 170 by 16.6.1998, p. 13 2.
74/152/EEC, 82/890/EEC of the Council of 17 December 1982 Directive 82/890/EEC amending the directives on the approximation of the laws of the Member States relating to agricultural and forestry tractors 378, 31.12.1982, p. 45 88/412/EEC of the Commission of 22 June 1988 Directive 88/412/EEC adapting to technical progress Council Directive 74/152/EEC on the approximation of the laws of the Member States relating to wheeled agricultural or forestry tractors to the maximum design speed and load platforms of 200 , 26.7.1988, p. 31 97/54/EC of the Parliament and of the Council of 23 September 1997 Directive 97/54/EC as regards the agricultural and forestry tractors to the maximum design speed of amending Council Directive 74/150/EEC, 74/151/EEC, 74/152/EEC, 74/346/EEC, 74/347/EEC, 75/321/EEC, 75/322/EEC, 76/432/EEC, 76/763/EEC, 77/311/EEC, 77/537/EEC , 78/764/EEC, 78/933/EEC, 79/532/EEC, 79/533/EEC, 80/720/EEC, 86/297/EEC, 86/415/EEC and 89/173/EEC 277 10.10.1997 p. 24.98/89/EC of the Commission of 20 November 1998 Directive 98/89/EC adapting to technical progress Council Directive 74/152/EEC relating to wheeled agricultural or forestry tractors to the maximum design speed and load platforms of 322 , 1.12.1998, p. 40.
74/346/EEC, 82/890/EEC of the Council of 17 December 1982 Directive 82/890/EEC amending the directives on the approximation of the laws of the Member States relating to agricultural and forestry tractors 378, 31.12.1982, p. 45 97/54/EC of the Parliament and of the Council of 23 September 1997 Directive 97/54/EC as regards the agricultural and forestry tractors to the maximum design speed of amending Council directives 74/150/EEC , 74/151/EEC, 74/152/EEC, 74/346/EEC, 74/347/EEC, 75/321/EEC, 75/322/EEC, 76/432/EEC, 76/763/EEC, 77/311/EEC, 77/537/EEC, 78/764/EEC, 78/933/EEC, 79/532/EEC, 79/533/EEC, 80/720/EEC, 86/297/EEC, 86/415/EEC and 89/173/EEC 277 10.10.1997 p. 24.98/40/EC of the Commission of 8 June 1998 Directive 98/40/EC adapting to technical progress Council Directive 74/346/EEC as regards rear-view mirrors for wheeled agricultural or forestry tractors 171, 17.6.1998, p. 28.
74/347/EEC, 79/1073/EEC of the Commission of 22 November 1979 by Directive 79/1073/EEC adapting to technical progress Council Directive 74/347/EEC on the approximation of the laws of the Member States relating to wheeled agricultural or forestry tractors field of vision and windscreen wipers for 331, 27.12.1979, p. 20 82/890/EEC

Council of 17 December 1982 Directive 82/890/EEC amending the directives on the approximation of the laws of the Member States relating to agricultural and forestry tractors 378, 31.12.1982, p. 45 97/54/EC of the Parliament and of the Council of 23 September 1997 Directive 97/54/EC as regards the agricultural and forestry tractors to the maximum design speed of amending Council Directive 74/150/EEC, 74/151/EEC , 74/152/EEC, 74/346/EEC, 74/347/EEC, 75/321/EEC, 75/322/EEC, 76/432/EEC, 76/763/EEC, 77/311/EEC, 77/537/EEC, 78/764/EEC, 78/933/EEC, 79/532/EEC, 79/533/EEC, 80/720/EEC, 86/297/EEC, 86/415/EEC and 89/173/EEC 277 10.10.1997 p. 24.5.
75/321/EEC, 82/890/EEC of the Council of 17 December 1982 Directive 82/890/EEC amending the directives on the approximation of the laws of the Member States relating to agricultural and forestry tractors 378, 31.12.1982, p. 45 88/411/EEC of the Commission of 21 June 1988 Directive 88/411/EEC adapting to technical progress Council Directive 75/321/EEC on the approximation of the laws of the Member States relating to the steering equipment of wheeled agricultural or forestry tractors 200 , 26.7.1988, p. 30 97/54/EC of the Parliament and of the Council of 23 September 1997 Directive 97/54/EC as regards the agricultural and forestry tractors to the maximum design speed of amending Council Directive 74/150/EEC, 74/151/EEC, 74/152/EEC, 74/346/EEC, 74/347/EEC, 75/321/EEC, 75/322/EEC, 76/432/EEC, 76/763/EEC, 77/311/EEC, 77/537/EEC , 78/764/EEC, 78/933/EEC, 79/532/EEC, 79/533/EEC, 80/720/EEC, 86/297/EEC, 86/415/EEC and 89/173/EEC 277 10.10.1997 p. 24.98/39/EC of the Commission of 5 June 1998 Directive 98/39/EC adapting to technical progress Council Directive 75/321/EEC relating to the steering equipment of wheeled agricultural or forestry tractors 170, 16.6.1998, p. 15.
75/322/EEC, 82/890/EEC of the Council of 17 December 1982 Directive 82/890/EEC amending the directives on the approximation of the laws of the Member States relating to agricultural and forestry tractors 378, 31.12.1982, p. 45 97/54/EC of the Parliament and of the Council of 23 September 1997 Directive 97/54/EC as regards the agricultural and forestry tractors to the maximum design speed of amending Council directives 74/150/EEC , 74/151/EEC, 74/152/EEC, 74/346/EEC, 74/347/EEC, 75/321/EEC, 75/322/EEC, 76/432/EEC, 76/763/EEC, 77/311/EEC, 77/537/EEC, 78/764/EEC, 78/933/EEC, 79/532/EEC, 79/533/EEC, 80/720/EEC, 86/297/EEC, 86/415/EEC and 89/173/EEC 277 10.10.1997 p. 24, 2000/2/EC of the Commission of 14 January 2000, Directive 2000/2/EC adapting to technical progress Council Directive 75/322/EEC on the Suppression of radio interference produced by spark-ignition engines fitted to wheeled agricultural or forestry tractors and Council Directive 74/150/EEC relating to wheeled agricultural or forestry tractors type approval of 21, 26.1.2000, p. 23 2001/3/EC of the Commission of 8 January 2001, Directive 2001/3/EC adapting to technical progress Council Directive 74/150/EEC relating to the type-approval of wheeled agricultural or forestry tractors and Council Directive 75/322/EEC relating to wheeled agricultural or forestry tractors to the Suppression of radio interference produced by spark-ignition engines fitted to 28 , 30.1.2001, p. 7 1.
76/432/EEC, 82/890/EEC of the Council of 17 December 1982 Directive 82/890/EEC amending the directives on the approximation of the laws of the Member States relating to agricultural and forestry tractors 378, 31.12.1982, p. 45 96/63/EC of the Commission of 30 September 1996, Directive 96/63/EC amending Council Directive 76/432/EEC on the approximation of the laws of the Member States relating to the braking devices of wheeled agricultural or forestry tractors 253 , 5.10.1996, p. 13 97/54/EC of the Parliament and of the Council of 23 September 1997 Directive 97/54/EC as regards the agricultural and forestry tractors to the maximum design speed of amending Council Directive 74/150/EEC, 74/151/EEC, 74/152/EEC, 74/346/EEC, 74/347/EEC, 75/321/EEC, 75/322/EEC, 76/432/EEC, 76/763/EEC, 77/311/EEC, 77/537/EEC , 78/764/EEC, 78/933/EEC, 79/532/EEC, 79/533/EEC, 80/720/EEC, 86/297/EEC, 86/415/EEC and 89/173/EEC 277 10.10.1997 p. 24, 8.
76/763/EEC, 82/890/EEC of the Council of 17 December 1982 Directive 82/890/EEC amending the directives on the approximation of the laws of the Member States relating to agricultural and forestry tractors 378, 31.12.1982, p. 45 97/54/EC of the Parliament and of the Council of 23 September 1997 Directive 97/54/EC as regards the agricultural and forestry tractors to the maximum design speed of amending Council directives 74/150/EEC , 74/151/EEC, 74/152/EEC, 74/346/EEC, 74/347/EEC, 75/321/EEC, 75/322/EEC, 76/432/EEC, 76/763/EEC, 77/311/EEC, 77/537/EEC, 78/764/EEC, 78/933/EEC, 79/532/EEC, 79/533/EEC, 80/720/EEC, 86/297/EEC, 86/415/EEC and 89/173/EEC 277 10.10.1997 p. 24, 1999/86/EC Council of 11 November 1999 Directive 1999/86/EC adapting to technical progress Directive 76/763/EEC on the the approximation of the laws of the Member States relating to passenger seats for wheeled agricultural or forestry tractors 297, 18.11.1999, p. 22 9.
77/311/EEC, 82/890/EEC of the Council of 17 December 1982 Directive 82/890/EEC amending the directives on the approximation of the laws of the Member States relating to agricultural and forestry tractors 378, 31.12.1982, p. 45 97/54/EC of the Parliament and of the Council of 23 September 1997 Directive 97/54/EC as regards the agricultural and forestry tractors to the maximum design speed of amending Council directives 74/150/EEC , 74/151/EEC, 74/152/EEC, 74/346/EEC, 74/347/EEC, 75/321/EEC, 75/322/EEC, 76/432/EEC, 76/763/EEC, 77/311/EEC, 77/537/EEC, 78/764/EEC, 78/933/EEC, 79/532/EEC, 79/533/EEC, 80/720/EEC, 86/297/EEC, 86/415/EEC and 89/173/EEC 277 10.10.1997 p. 24.10.
77/536/EEC 87/354/EEC of the Council of 25 June 1987 Directive 87/354/EEC amending certain directives on the approximation of the laws of the Member States relating to industrial products with respect to the distinctive numbers and letters indicating the Member 192, 11.7.1987, p. 43 89/680/EEC of the Council of 21 December 1989 directive 89/680/EEC amending Directive 77/536/EEC on the approximation of the laws of the Member States relating to the roll-over protection structures of wheeled agricultural or forestry tractors 398 , 30.12.1989, p. 26 of 1999/55/EC of the Commission of 1 June 1999, Directive 1999/55/EC adapting to technical progress Council Directive 77/536/EEC relating to the roll-over protection structures of wheeled agricultural or forestry tractors 146, 11.6.1999, p. 28 11.
77/537/EEC, 82/890/EEC

Council of 17 December 1982 Directive 82/890/EEC amending the directives on the approximation of the laws of the Member States relating to agricultural and forestry tractors 378, 31.12.1982, p. 45 97/54/EC of the Parliament and of the Council of 23 September 1997 Directive 97/54/EC as regards the agricultural and forestry tractors to the maximum design speed of amending Council Directive 74/150/EEC, 74/151/EEC , 74/152/EEC, 74/346/EEC, 74/347/EEC, 75/321/EEC, 75/322/EEC, 76/432/EEC, 76/763/EEC, 77/311/EEC, 77/537/EEC, 78/764/EEC, 78/933/EEC, 79/532/EEC, 79/533/EEC, 80/720/EEC, 86/297/EEC, 86/415/EEC and 89/173/EEC 277 10.10.1997 p. 24.12.
78/764/EEC, 82/890/EEC of the Council of 17 December 1982 Directive 82/890/EEC amending the directives on the approximation of the laws of the Member States relating to agricultural and forestry tractors 378, 31.12.1982, p. 45 83/190/EEC of the Commission of 28 March 1983 Directive 83/190/EEC adapting to technical progress Council Directive 78/764/EEC on the approximation of the laws of the Member States relating to the driver's seat on wheeled agricultural or forestry tractors 109 , 26.4.1983., p. 13 88/465/EEC of the Commission of 30 June 1988, Directive 88/465/EEC adapting to technical progress Council Directive 78/764/EEC on the approximation of the laws of the Member States relating to the driver's seat on wheeled agricultural or forestry tractors 228, 17.8.1988, p. 31 97/54/EC of the Parliament and of the Council of 23 September 1997 Directive 97/54/EC as regards the agricultural and forestry tractors to the maximum design speed of amending Council directives 74/150/EEC , 74/151/EEC, 74/152/EEC, 74/346/EEC, 74/347/EEC, 75/321/EEC, 75/322/EEC, 76/432/EEC, 76/763/EEC, 77/311/EEC, 77/537/EEC, 78/764/EEC, 78/933/EEC, 79/532/EEC, 79/533/EEC, 80/720/EEC, 86/297/EEC, 86/415/EEC and 89/173/EEC 277 10.10.1997 p. 24, 1999/57/EC of the Commission of 7 June 1999, Directive 1999/57/EC adapting to technical progress Council Directive 78/764/EEC with regard to the driver's seat on wheeled agricultural or forestry tractors 148, 15.6.1999, p. 35 13.
78/933/EEC, 82/890/EEC of the Council of 17 December 1982 Directive 82/890/EEC amending the directives on the approximation of the laws of the Member States relating to agricultural and forestry tractors 378, 31.12.1982, p. 45 97/54/EC of the Parliament and of the Council of 23 September 1997 Directive 97/54/EC as regards the agricultural and forestry tractors to the maximum design speed of amending Council directives 74/150/EEC , 74/151/EEC, 74/152/EEC, 74/346/EEC, 74/347/EEC, 75/321/EEC, 75/322/EEC, 76/432/EEC, 76/763/EEC, 77/311/EEC, 77/537/EEC, 78/764/EEC, 78/933/EEC, 79/532/EEC, 79/533/EEC, 80/720/EEC, 86/297/EEC, 86/415/EEC and 89/173/EEC 277 10.10.1997 p. 24, 1999/56/EC of the Commission of 3 June 1999, Directive 1999/56/EC adapting to technical progress Council Directive 78/933/EEC in relation to the installation of lighting and light-signalling devices on wheeled agricultural and forestry tractors 146, 11.6.1999, p. 31 14.
79/532/EEC, 82/890/EEC of the Council of 17 December 1982 Directive 82/890/EEC amending the directives on the approximation of the laws of the Member States relating to agricultural and forestry tractors 378, 31.12.1982, p. 45 97/54/EC of the Parliament and of the Council of 23 September 1997 Directive 97/54/EC as regards the agricultural and forestry tractors to the maximum design speed of amending Council directives 74/150/EEC , 74/151/EEC, 74/152/EEC, 74/346/EEC, 74/347/EEC, 75/321/EEC, 75/322/EEC, 76/432/EEC, 76/763/EEC, 77/311/EEC, 77/537/EEC, 78/764/EEC, 78/933/EEC, 79/532/EEC, 79/533/EEC, 80/720/EEC, 86/297/EEC, 86/415/EEC and 89/173/EEC 277, 10.10.1997, p. 24.15.
79/533/EEC, 82/890/EEC of the Council of 17 December 1982 Directive 82/890/EEC amending the directives on the approximation of the laws of the Member States relating to agricultural and forestry tractors 378, 31.12.1982, p. 45 97/54/EC of the Parliament and of the Council of 23 September 1997 Directive 97/54/EC as regards the agricultural and forestry tractors to the maximum design speed of amending Council directives 74/150/EEC , 74/151/EEC, 74/152/EEC, 74/346/EEC, 74/347/EEC, 75/321/EEC, 75/322/EEC, 76/432/EEC, 76/763/EEC, 77/311/EEC, 77/537/EEC, 78/764/EEC, 78/933/EEC, 79/532/EEC, 79/533/EEC, 80/720/EEC, 86/297/EEC, 86/415/EEC and 89/173/EEC 277 10.10.1997 p. 24, 1999/58/EC of the Commission of 7 June 1999, Directive 1999/58/EC adapting to technical progress Council Directive 79/533/EEC relating to coupling and reversing devices for wheeled agricultural or forestry tractors 148, 15.6.1999, p. 37 16.
79/622/EEC, 82/953/EEC of the Commission of 15 December 1982 Directive 82/953/EEC adapting to technical progress Council Directive 79/622/EEC on the approximation of the laws of the Member States relating to the roll-over protection structures of wheeled agricultural or forestry tractors (static testing) 386, 31.12.1982, p. 31 87/354/EEC of the Council of 25 June 1987 Directive 87/354/EEC amending certain directives on the approximation of the laws of the Member States relating to industrial products with respect to the distinctive numbers and letters indicating the Member 192 , 11.7.1987, p. 43 88/413/EEC of the Commission of 22 June 1988 Directive 88/413/EEC adapting to technical progress Council Directive 79/622/EEC on the approximation of the laws of the Member States relating to the roll-over protection structures of wheeled agricultural or forestry tractors (static testing) 200, 26.7.1988, p. 32 1999/40/EC of the Commission of 6 May 1999 Directive 1999/40/EC adapting to technical progress Council Directive 79/622/EEC on the approximation of the laws of the Member States relating to the roll-over protection structures of wheeled agricultural or forestry tractors (static testing) 124 , 18.5.1999, p. 11 17.
80/720/EEC, 82/890/EEC of the Council of 17 December 1982 Directive 82/890/EEC amending the directives on the approximation of the laws of the Member States relating to agricultural and forestry tractors 378, 31.12.1982, p. 45 88/414/EEC of the Commission of 22 June 1988 Directive 88/414/EEC adapting to technical progress Council Directive 80/720/EEC on the approximation of the laws of the Member States relating to the operating space , access to the driving position and the doors and Windows of wheeled agricultural and forestry tractors 200, 26.7.1988, p. 34 97/54/EC

Parliament and of the Council of 23 September 1997 Directive 97/54/EC as regards the agricultural and forestry tractors to the maximum design speed of amending Council Directive 74/150/EEC, 74/151/EEC, 74/152/EEC, 74/346/EEC, 74/347/EEC, 75/321/EEC, 75/322/EEC, 76/432/EEC, 76/763/EEC, 77/311/EEC, 77/537/EEC, 78/764/EEC , 78/933/EEC, 79/532/EEC, 79/533/EEC, 80/720/EEC, 86/297/EEC, 86/415/EEC and 89/173/EEC 277 10.10.1997 p. 24.18.
86/297/EEC 97/54/EC of the Parliament and of the Council of 23 September 1997 Directive 97/54/EC as regards the agricultural and forestry tractors to the maximum design speed of amending Council Directive 74/150/EEC, 74/151/EEC, 74/152/EEC, 74/346/EEC, 74/347/EEC, 75/321/EEC, 75/322/EEC, 76/432/EEC, 76/763/EEC, 77/311/EEC , 77/537/EEC, 78/764/EEC, 78/933/EEC, 79/532/EEC, 79/533/EEC, 80/720/EEC, 86/297/EEC, 86/415/EEC and 89/173/EEC 277, 10.10.1997, p. 24.19.
86/298/EEC, 89/682/EEC of the Council of 21 December 1989 directive 89/682/EEC amending Directive 86/298/EEC on rear-mounted roll-over protection structures of narrow-track wheeled agricultural and forestry tractors 398, 30.12.1989, p. 29 2000/19/EC of the Commission of 13 April 2000, Directive 2000/19/EC adapting to technical progress Council Directive 86/298/EEC on rear-mounted roll-over protection structures of narrow-track wheeled agricultural and forestry tractors 94 , 14.4.2000, p. 31, 2005/67/EC of the Commission of 18 October 2005 Directive 2005/67/EC amending Council Directive 86/298/EEC, annexes I and II to Council Directive 87/402/EEC and annexes I and II to the directive of the European Parliament and of the Council 2003/37/EC annex I, II and III relating to agricultural or forestry tractors type approval to the appropriate custom 273 , 19 October, p. 17-20.
86/415/EEC 97/54/EC of the Parliament and of the Council of 23 September 1997 Directive 97/54/EC as regards the agricultural and forestry tractors to the maximum design speed of amending Council Directive 74/150/EEC, 74/151/EEC, 74/152/EEC, 74/346/EEC, 74/347/EEC, 75/321/EEC, 75/322/EEC, 76/432/EEC, 76/763/EEC, 77/311/EEC , 77/537/EEC, 78/764/EEC, 78/933/EEC, 79/532/EEC, 79/533/EEC, 80/720/EEC, 86/297/EEC, 86/415/EEC and 89/173/EEC 277 10.10.1997 p. 24.21.
87/402/EEC, 89/681/EEC of the Council of 21 December 1989 directive 89/681/EEC amending Directive 87/402/EEC on narrow-track wheeled agricultural and forestry tractors roll-over protection structures mounted in front of the driver's seat 398, 30.12.1989, p. 27 2000/22/EC of the Commission of 28 April 2000, Directive 2000/22/EC adapting to technical progress Council Directive 87/402/EEC on narrow-track wheeled agricultural and forestry tractors roll-over protection structures mounted in front of the driver's seat 107, 4.5.2000, p. 26, 2005/67/EC of the Commission of 18 October 2005 Directive 2005/67/EC amending Council Directive 86/298/EEC, annexes I and II to Council Directive 87/402/EEC and annexes I and II to the directive of the European Parliament and of the Council 2003/37/EC annex I, II and III in relation to the agricultural or forestry tractor type-approval to adapt the 273, 19 October, p. 17.
89/173/EEC 97/54/EC of the Parliament and of the Council of 23 September 1997 Directive 97/54/EC as regards the agricultural and forestry tractors to the maximum design speed of amending Council Directive 74/150/EEC, 74/151/EEC, 74/152/EEC, 74/346/EEC, 74/347/EEC, 75/321/EEC, 75/322/EEC, 76/432/EEC, 76/763/EEC, 77/311/EEC , 77/537/EEC, 78/764/EEC, 78/933/EEC, 79/532/EEC, 79/533/EEC, 80/720/EEC, 86/297/EEC, 86/415/EEC and 89/173/EEC 277 10.10.1997 p. 24, 2000/1/EC of the Commission of 14 January 2000, Directive 2000/1/EC adapting to technical progress Council Directive 89/173/EEC on the approximation of the laws of the Member States relating to certain components and characteristics of wheeled agricultural or forestry tractors 21 , 26.1.2000, p. 16-23.
2000/25/EC, 2005/13/EC of the Commission of 21 February 2005 Directive 2005/13/EC of the European Parliament and the Council amending Directive 2000/25/EC in relation to emission of gaseous and particulate pollutants by engines intended to power agricultural or forestry tractors, and amending Annex I to the directive of the European Parliament and of the Council 2003/37/EC relating to the type-approval of agricultural or forestry tractors 55 1.3.2005, p. 35, II., part A (1) this table shows the separate directives on motor vehicles (latest version in force of the EC type-approval) may be applied to the corresponding separate directives on agricultural and forestry tractors instead.
 No subject in the table of part I of the framework directive (for motor vehicles) the name of the framework directive OJ L 1.5.
 Audible warning device 70/388/EEC of the Council of 27 July 1970 directive 70/388/EEC on the approximation of the laws of the Member States relating to audible warning devices for vehicles 176, 10.8.1970, p. 12-1.6.
 Sound level (external) 70/157/EEC of the Council of 6 February 1970 directive 70/157/EEC on the approximation of the laws of the Member States relating to motor-vehicle permissible sound level and the exhaust system of 42, 23.2.1970, p. 1. 16 4.1.
 Area of vision and windscreen wipers 77/649/EEC of the Council of 27 September 1977 Directive 77/649/EEC on the approximation of the laws of the Member States relating to the field of vision of motor vehicle drivers 284, 10.10.1978, p. 11 5.1.
 Steering effort 70/311/EEC of the Council of 8 June 1970 directive 70/311/EEC on the approximation of the laws of the Member States relating to the steering equipment for motor vehicles and their trailers 133, 18.6.1970, p. 10 6.1.
 Damping suppression of 72/245/EEC Council 20 June 1972 by Directive 72/245/EEC on the approximation of the laws of the Member States relating to the Suppression of radio interference produced by spark-ignition engines fitted to motor vehicles 152, 6.7.1972, p. 15 7.1.
 Braking 71/320/EEC of the Council on July 26, 1971 in Directive 71/320/EEC on the approximation of the laws of the Member States of certain categories of motor vehicles and their trailers braking devices 202, 6.9.1971, p. 1. 37 14.1.
 Rear reflex reflectors 76/757/EEC

Council of 27 July 1976 Directive 76/757/EEC on the approximation of the laws of the Member States relating to reflex reflectors for motor vehicles and their trailers 262, 27.9.76, p. 1. 32 14.1.
 Rear lamps 76/758/EEC Council of 27 July 1976 Directive 76/758/EEC on the approximation of the laws of the Member States relating to motor vehicles and their trailers to the end-outline marker lamps, front position (side) lamps, rear position (side) lamp and stop lamp 262, 27.9.76, p. 1. 54 14.1.
 Direction indicators 76/759/EEC Council of 27 July 1976 Directive 76/759/EEC on the approximation of the laws of the Member States relating to motor vehicles and their trailers and of direction indicator lamps, 27.9.76, p. 262. 71 14.1.
 Number-plate 76/760/EEC Council July 27 1976 Directive 76/760/EEC on the approximation of the laws of the Member States relating to motor vehicles and their trailers and of rear registration plate lamps, 262, 27.9.76, p. 1. 85 14.1.
 Headlamps 76/761/EEC of the Council of 27 July 1976 Directive 76/761/EEC on the approximation of the laws of the Member States relating to motor-vehicle headlamps which function as main-beam and/or dipped-beam headlamps and filament lamps for such headlamps to 262, 27.9.76, p. 1. 96 14.1.
 Dipped-beam headlamps of Council 76/761/EEC of 27 July 1976 Directive 76/761/EEC on the approximation of the laws of the Member States relating to motor-vehicle headlamps which function as main-beam and/or dipped-beam headlamps and filament lamps for such lamps, 14.1.
 Front fog lamps 76/762/EEC Council July 27 1976 Directive 76/762/EEC on the approximation of the laws of the Member States relating to front fog lamps for motor vehicles and filament lamps for such lamps 262, 27.9.76, p. 1. 122 14.1.
 Rear fog lamps 77/538/EEC of the Council of 28 June 1977 Directive 77/538/EEC on the approximation of the laws of the Member States relating to motor vehicles and their trailers and of rear fog lamps 220, 29.8.1977, p. 1. 60 14.1.
 Reversing lamps 77/539/EEC of the Council of 28 June 1977 Directive 77/539/EEC on the approximation of the laws of the Member States relating to reversing lamps for motor vehicles and their trailers 220, 29.8.1977, p. 1. 72 22.2.
 Secure glass 92/22/EEC of the Council of 31 March 1992 Directive 92/22/EEC relating to motor vehicles and their trailers on safety glazing and glazing materials 129, 14.5.1992, p. 1. 11 23.1.
 Pollutant emissions 88/77/EEC of the Council of 3 December 1987 Directive 88/77/EEC on the approximation of the laws of the Member States relating to the measures to be taken against the emission of gaseous pollutants from diesel engines for use in vehicles, 36, 9.2.1988, p. 1. 33. part II (B) (1) this table shows that the regulation of the Council of 27 November 1997 decision 97/836/EC concerning the accession of the European Community to United Nations Economic Commission for Europe agreement of uniform technical prescriptions concerning the approval of wheels for vehicles, equipment and parts which can be fitted and/or be used on wheeled vehicles and the conditions for mutual recognition of approvals granted on the basis of these requirements (hereinafter referred to as the agreement) and the latest version of the community as a party to the said agreement, in accordance with the relevant separate Directive EC type-approval is recognised on the day of the award may be applied to the table in part II a. above the corresponding separate directives on agricultural tractors and the corresponding separate directives on motor vehicles instead.
 
No subject in the table of part I of the UN/ECE Regulation number 1.5.
 Audible warning device R 28 1.6.
 Sound level (external) R 51 4.1.
 Area of vision and windscreen wipers R 71 5.1.
 Steering R 79 6.1.
 Damping suppression of R 10 7.1.
 R 13 13.1 the service braking system.
 Lighting installation R 86 * 14.1.
 Rear reflex reflectors R 3 14.1.
 Rear lamp R 7 14.1.
 Direction indicator lamp R 6 14.1.
 Number plate lamp R 4 14.1.
 Headlamps R R R l-8-20-R 98 14.1.
 Dipped-beam headlamps R R R l-8-20-R 98 14.1.
 Front fog lamps R 19 14.1.
 Rear fog lamps R 38 14.1.
 Reversing lamps R 22.2 23.
 Secure glass R 43 ** 23.1.
 Pollutant emissions R 49/96 R *** notes.
1. Only in the case of devices referred to in the corresponding directive.
2. Other than windscreens.
3. *** only in relation to the period referred to in the corresponding directive.
 
II. compliance with the standardized part C of the Organisation for economic cooperation and development (OECD) codes (1) the Test bulletins (complete) which conform to the OECD codes given below may be used in place of the test report prepared pursuant to the relevant separate directives.
No table of part I of the directive subject to the OECD kodi1 10.1.
77/536/EEC official agricultural or forestry tractor tests the protection structure (dynamic test) code 3 26.1 16.1 76/115/EEC.
79/622/EEC official agricultural or forestry tractor roll-over protection device test (static test) code 4 26.1.
76/115/EEC 19.1.
86/298/EEC official agricultural or forestry tractors of narrow wheels of the rear-mounted protection structure test code 7 26.1.
76/115/EEC 21.1.
87/402/EEC agricultural or forestry Official of narrow-track wheeled tractors in front-mounted protection structures test code 6 26.1.
76/115/EEC SD2 official agricultural or forestry tractor crawler tests the protection code 8 26.1.
76/115/EEC notes.
1 Test newsletters must comply with the OECD decision c (2005) 1. In regard to safety belt anchorages test bulletins can be recognised as equivalent to the anchorages that are tested.
On the basis of decision K (2000) 59, as last amended by decision c (2003) 252, test messages that comply with the code may be accepted during the transition period, which lasts one year, from 1 to decision c (2005) publication date of the OECD Web site, that is, until 21 April 2006.

2 SD: to be included in a separate directive.
 
 
Appendix 1 part I definition of special vehicles and vehicle EC type-approval requirements 1. T4 tractors category 1.1. T 4.1 with great clearance Tractor tractors designed for working with high-growing crops (e.g. grapes). They are with high chassis or chassis part that allows them to move forward in parallel with the crops the left and right wheels on either side of one or more rows of crops. They are intended for the transport of the machine or operation which may be set up in the front, between the axles, rear or on the platform. If the tractor is in working condition, the ground clearance perpendicular to the crop rows exceeds 1000 mm. If the tractor (in accordance with the standard EN ISO 789-6:2005 "agricultural tractors – test procedures – part 6: Centre of gravity") of the Centre of gravity height (measured relative to the Earth, which is equipped with a tractor usually used tyres) against the average minimum distance between wheels on all axles exceeds 0.90, the maximum design speed must not exceed 30 km/h. 1.2. T 4.2 bulky tractors tractors, which characteristically large sizes and intended mainly for large agricultural land area processing.
1.3. T4.3 low-clearance tractors with all-wheel-drive agricultural or forestry tractors whose interchangeable equipment intended for use in agriculture or forestry and which are characterised by one or more of the PTO equipped bearing frames, the technically permissible mass not exceeding 10 tonnes and of this mass to the maximum unladen mass in running order is less than 2.5. Furthermore, tractor (in accordance with the standard EN ISO 789-6:2005 "agricultural tractors – testing procedures-part 6 : "The Centre of gravity) of the Centre of gravity height (measured relative to the Earth, which is equipped with a tractor usually used tyres) is less than 850 mm. 2. C4 category-C 4.1: crawler tractor with a big ground clearance: idem T 4.1 categories of tractors.
 
Part II applicability of the separate directives to special vehicles No.
 The base directive and the subject matter of the applicability of the category annex T T T C 4.1 4.1 4.2 4.3 1.1.
 Maximum laden mass 74/151/EEC X X X X 1.2.
 Number plate 74/151/EEC, II (X) (X) X (X) 1.3.
 Fuel tank 74/151/EEC X X X 1.4 X III.
 The ballast masses 74/151/EEC (IV) X X X X 1.5.
 Audible warning device 74/151/EEC X X X X V 1.6.
 Sound level (external) 74/151/EEC, RESPECTIVELY (X) (X) X (X) 2.1.
 The maximum speed of 74/152/EEC annex 1 X X X X 2.2.
 Cargo platform 74/152/EEC (2) (X) X (X) (X) 3.1.
 Rear-view mirrors, 74/346/EEC (X) X X (X) 4.1.
 Area of vision and windscreen wipers 74/347/EEC (X) (X) X (X) 5.1.
 The steering system 75/321/EEC X X X SD 6.1.
 Electromagnetic disturbance 75/322/EEC X X X X 7.1.
 Braking devices 76/432/EEC (X) X (X) X 8.1.
 Passenger seats to 76/763/EEC X X X X 9.1.
 Sound level (internal), 77/311/EEC (X) X (X) X 10.1.
 The roll-over protection structure 77/536/EEC X X SD SD 12.1.
 The driving position 78/764/EEC (X) X (X) X 13.1.
 Lighting installation of 78/933/EEC (X) (X) X (X) 14.1.
 Lights and warning devices 79/532/EEC X X X X 15.1.
 Coupling and reversiekārt 79/533/EEC (X) X (X) X 16.1.
 ROPS (static testing) 79/622/EEC X X SD SD 17.1.
 The operating space, access to the driving position of 80/720/EEC (X) (X) (X) (X) 18.1.
 PTO 86/297/EEC X X X X 19.1.
 Rear mounted ROPS (narrow-track wheeled tractors) 86/298/EEC — — — — 20.1.
 Installing controls 86/415/EEC X X X X 21.1.
 Front mounted ROPS (narrow-track wheeled tractors) 87/402/EEC — — — — 22.1.
 Size and mass of the trailer 89/173/EEC I (X) X (X) X 22.2.
 Glass 89/173/EEC X X X 22.3 X III.
 Speed regulator 89/173/EEC, II, 1 X X X X 22.4.
 Drive components protection 89/173/EEC, (II), 2 (X) X (X) X 22.5.
 The mechanical coupling device 89/173/EEC (IV) X (X) X X 22.6.
 Number plate 89/173/EEC X X V X X 14.1.
 Trailer brake transmission 89/173/EEC (VI) X (X) X X 23.1.
 Pollutant emissions 2000/25/EC X X X X 24.1.
 Riepas1 […/…/EC] SD SD SD-25.1.
[…/…/EC] SD-Stabilitāte1-SD legend.
X-apply fully.
(X)-apply grozītu2.
SD-need a separate directive.
– do not apply.
 The notes.
1 pending the adoption of directives on tyres and stability, the fact that individual directives, shall not prevent the grant whole-vehicle type approval.
2 when granting EC type-approval, the brackets are not used.
 
Appendix 2 procedures to be followed during EC type-approval 1. If the application is made in accordance with rules 5 and 6 point (in accordance with the model shown in Annex B), the EC type-approval authority: 1.1 check that the component EC type-approvals and EC type-approvals issued pursuant to the separate directives are in force, and organizes the tests and checks specified in any of the separate directives which are not taken into account in issuing such approvals;
1.2. documentation, make sure that the vehicle specification (s) and data contained in the information document of the vehicle (I) include information packet data or the approval reports, which document certifying components, systems or separate technical units approved in accordance with the relevant separate directives and, if the point number in part I of the information document is not included in any of the separate directives information package, confirm that the relevant part or parameter conforms to the particulars in the information folder;

1.3. make or arrange for vehicle parts and systems to vehicles type approved models, to verify that the vehicle (s) is/are built in accordance with (i) the information package included relevant data, the authenticity of which has been approved for all approvals granted pursuant to the separate directives;
1.4. If necessary, carry out or arrange for checks in respect of separate technical units.
2. the number of vehicles to be inspected is adequate to Appendix 2 of this annex 1.3. checks referred to check various combinations to be approved in accordance with the following characteristics: 2.1 the engine;
2.2. the gearbox;
2.3. powered axles (number, position, interconnection);
2.4. steered axles (number and position);
2.5. braked axles (number);
2.6. the roll-over protection structure.
3. If the application is made in accordance with rules 5 and 6 point (in accordance with the model shown in Annex A), the EC type-approval authority shall: 3.1 organizing the necessary tests and checks defined by each relevant separate directive;
3.2. make sure that the vehicle conforms to the information folder contains data and technical requirements of each of the relevant separate directive;
3.3. If necessary, carry out or arrange for checks on the installation of separate technical units.
 
Chapter c vehicle EC type-approval certificate Appendix 3 EC type-approval certificate numbering system (1) the approval number consists of four parts (if approve the finished vehicles) or of five parts (if approved by the systems, components and separate technical units) in accordance with the following requirements (components and separate technical units shall be marked in accordance with the relevant separate directives; parts always separated by an asterisk): 1.1 number part 1: the lower case letter "e" , followed by the distinguishing number or letters of the Member State which has granted type-approval: 1 for Germany, 2 for France, 3 for Italy, 4 for the Netherlands, Sweden, Belgium, 5-6, Spain 9, United Kingdom of Great Britain and Northern Ireland-11,-12 for Austria, 13 for Luxembourg, 17 for Finland, 18 for Denmark, Portugal, Greece, 23-21, Ireland – 24, the Czech Republic, Estonia, Hungary, 29-8, Cyprus – CY, Latvia-Lithuania-32, 36-7, Malta, Hungary, Poland – 20 MT , Slovenia, Slovakia-26-27;
1.2. number part 2 – the number of the base directive..........................................;
1.3. number part 3 – the number of the directive, to which the latest amendments relating to approval: 1.3.1. in the case of a vehicle approval – the latest directive amending Directive 2003/37/EC one (more) article (s);
1.3.2. If approved in accordance with the separate directives, the recent directive that includes specific provisions which the system, component or separate technical unit must comply;
1.3.3. If the directive contains various effective dates that apply to different technical standards, an alphabetical letter must be added. This letter will indicate the specific technical requirements, on the basis of which issued the approval;
1.4. number of part 4 – a four-digit sequential number (if necessary, with leading zeros as applicable) to denote the approval number. For each base directive numbering starts at 0001;
1.5. number 5 – two-digit sequence number (if necessary, with zero in the beginning) to denote the extension of approval. For each base approval number numbering starts at 2.00 pm. If the vehicle is approved, part 2 missing.
3. Number of part 5 releases only the mandatory (s) manufacturer's plate (s).
4. Example of the third system approval (which so far have not had the extension), issued in France in respect of Directive 80/720/EEC: e 2 * 80/720 * 88/414 * 0003 * 00, if directive, which includes two implementation stages A and b. – 5. Example of the second extension to the fourth vehicle in relation confirmation issued by the United Kingdom: e 11 * 97/54 * 0004 * 02 in which case Directive 97/54/EC would be temporary recent directive amending the articles of the framework directive.
6. Example of the approval number stamped on the vehicle manufacturer's statutory plate (s) (s): e 11 * 97/54 * 0004. Minister of Agriculture m. Rose proposed the Ministry of agriculture in annex 2 versions of the Cabinet of Ministers of 27 June 2006 regulations no 535 information document paraugs1 (1) all of the information document referred to in these regulations and in the separate directives, composed only of the documents included in this list, and the number of using this list, only the specified numbering system.
(2) the following information, if applicable must be supplied in triplicate and include a list of contents. All drawings submitted, which accurately reflects the information, and in sufficient detail on size A4 or on a folder. If you have photos, they are sufficiently detailed.
 
Sample a complete list of model A is used if no EC type-approval certificate granted under the specific directives.
0. General information 0.1. Make (s) (trade mark of the manufacturer) …. …. …. …. …. …. …. …. …. …. …. …. …. …. … ….
0.2. Type (specify any variants and versions) … … … … … … … … … … … … … … … … … … … … ….
0.2.0. Situation in terms of completeness: complete one stage/complete/pabeigts2.
If the vehicle is completed, indicate the previous name and address of the manufacturer and the incomplete or complete vehicle approval number.
0.2.1. Commercial name (s) (if applicable)....................................................................... "
0.3. means of identification of type, if marked on the vehicle: 0.3.1. Manufacturer's plate (location and method of affixing of the) … … … … … … … … ….
0.3.2. chassis number (location) …. …. …. …. …. …. …. …. …. …. …. …. …. …. …. …. …. …. ….
0.4. vehicle kategorija3................................................................................... "
0.5. Name and address of the manufacturer................................................................................. "

0.6. A minimum the manufacturer's plate and the inscription, location and method of affixing of the (photographs and drawings)..................................................................................................... "
0.7. The EC type-approval mark the location of the systems, components and separate technical units, and method of affixing of the....................................... "
0.8. Assembly plant (s) name (s) and address (s) … … … … … … … … … … … … … … ….
1. General construction characteristics of the vehicle (added 3/4 front and 3/4 rear photographs or drawings of the prototype and the dimensional drawing of the whole vehicle scale) 1.1. number of axles and wheels.................................................................................................. "
1.1.1. the Double axis of number and position (if applicable) … … … … … … … … … … … … … … … … ….
1.1.2. the number and the steered axle location. … … … … … … … … … … … … … … … … … … … … … … ….
1.1.3. Powered axles (number, position, connection)................................................ "
1.1.4. Braked axles (number, position) …. …. …. …. …. …. …. …. …. …. …. …. …. …. …. ….
1.2. the engine's location and position …................................................................ "
1.3. position of the steering wheel: right/left/vidū4 1.4. Reversible driving position: Yes/nav5 1.5. Chassis: backbone chassis/chassis with side members/articulated chassis/cita6-1.6. vehicle designed for driving on the left/right pusi7 and 2 izmēri8 (in kg and mm) (where necessary, refer to drawings) 2.1. Unladen weight (s) 2.1.1. Unladen weight (s) running kārtībā9 (serving as a reference for the various separate directives) (with roll-over protection structure without accessories, but with coolant, oils, fuel, tools and driver): – maximum 10.....................................................................................................................-the minimum … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … ….
2.1.1.1. The (this) (s) of mass among the axles and, if there is a semi-trailer (or interchangeable towed machinery) or a centre-axle trailer (or interchangeable towed machinery), the load on the coupling point................................................................................................ "
2.2. Maximum limit (s) (s) (s), as declared by the manufacturer.......................... "
2.2.1. technically permissible maximum (s) (s) complete (s) mass (s) according to the tyre Specification 2.2.2. This (these) (s) of mass among the axles and, if there is a semi-trailer (or interchangeable towed machinery) or a centre-axle trailer (or interchangeable towed machinery), the load on the coupling point................................................................................................ "
2.2.3. Limits of this (these) (s) mass distribution among the axles (specify the minimum limits in percentages on the front axle and on the rear axle) and, if there is a semi-trailer (or interchangeable towed machinery) or a centre-axle trailer (or interchangeable towed machinery), the load on the coupling point 2.2.3.1. masses (s) and tyre (s) axle.
 Tyres (size) of dead weight technically permissible maximum mass on each axle, the maximum permissible vertical on the coupling point 1 2 3 slodze7 2.2.4. Payload (s) 11 … … … … … … … … … … … … … … … … … … … … … … … … … … … … ….
2.3. Ballast masses (total weight, material, number of components)................................... "
2.3.1. This (these) weight (s) among the axles … … … … … … … … … … … … … … … … … … … … … ….
2.4. technically permissible towable mass of the tractor (s), if any: 2.4.1. Drawbar trailer (interchangeable towed machinery)............................................ "
2.4.2. Semi-trailer (interchangeable towed machinery)............................................................... "
2.4.3. Centre-axle trailer (interchangeable towed machinery)................................. "
2.4.4. total technically permissible mass (s) (s) with the trailer (interchangeable towed machinery) articulated tractor for each trailer (interchangeable towed machinery) braking equipment configuration..................................................................................................... "
2.4.5. maximum trailer (interchangeable towed machinery) which may be mass, Wolf … … … ….
2.4.6. The coupling point location 2.4.6.1. Height above the ground 2.4.6.1.1. Maximum height … … … … … … … … … … … … … … … … … … … … … … … … … … ….
2.4.6.1.2. Minimālais augstums .......................................................................................
2.4.6.2. Distance to the vertical plane passing through the axis of the rear axle........................... "
2.4.6.3. maximum static vertical load/technically permissible mass on the coupling point tractor 2.4.6.3.1........................................................................................................ "
2.4.6.3.2. Semi-trailer (interchangeable towed machinery for) or a trailer with central axle (interchangeable towed to the car) … … … … … … … … … … … … … … … … … … … … … … … … … … … ….
Garenbāze12 2.5 2.5.1. Semi-trailer (interchangeable towed machinery) 2.5.1.1. the distance between the jūgtap and the first rear axle.................................................... "
2.5.1.2. Distance between the jūgtap and the semi-trailer (interchangeable towed machinery), the rear … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … ….
2.6. maximum and minimum distance between the wheels of each axle (measured between the commonly used tire or double tyre planes of symmetry) (to be specified by the manufacturer) 13...................... the vehicle dimensions 2.7 range (General and driving on the road) 2.7.1. Chassis without 2.7.1.1. Garums14............................................................................................................. "
2.7.1.1.1. Maximum permissible length of the completed vehicle............................... "
2.7.1.1.2. Minimum permissible length for the completed vehicle................................. "

3.2.6.4. engine electronic control system location:......................................... "
3.2.6.4.1. Ko tā uztver: ....................................................................................................
3.2.6.4.2. Ko tā vada: ......................................................................................................
Part 3-compression ignition engine family 3.3. Engine family essential characteristics of the engine type enum 3.3.1 family 3.3.1.1. name of engine family:. … … … … … … … … … … … … … … … … … … … … … … … … … ….
3.3.1.2. specification of engine types within a particular family: parent engine engine type number of Cylinders rated speed (r/min) fuel delivery per stroke (mm3) at rated speed Rated net power (kW) the declared maximum torque speed (r/min) fuel delivery per stroke (mm3) maximum torque the maximum torque (Nm) minimum idle speed (r/min) drum work, expressed in% of parent engine 100 4. part-engine type 3.4. essential characteristics of the engine type engine description of 3.4.1 3.4.1.1. the manufacturer : .............................................................................................................
3.4.1.2. manufacturer's engine code as affixed to engines:.............................................. "
3.4.1.3. cycle: four stroke/two stroke (2) 3.4.1.4. Bore:........................................................................................... mm 3.4.1.5. stroke: … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … mm. number of Cylinders and 3.4.1.6 layout:............................................................................. "
3.4.1.7. Work:............................................................................................... CC 3.4.1.8 rated speed:....................................................................... r/min revolutions 3.4.1.9. maximum torque: ... … …. …. …. …. …. …. …. …. …. r/min 3.4.1.10. Compression ratio (37): 3.4.1.11. Combustion system:.......................................................................................... "
3.4.1.12. Drawings of combustion chamber and piston head drawing (s): … … … … … … … … … … … … … … … … ….
3.4.1.13. Intake and exhaust openings the minimum cross-sectional area:........................ "
3.4.1.14. Cooling 3.4.1.14.1. Cooler Cooler type: 3.4.1.14.1.1........................................................................................... "
3.4.1.14.1.2. Circulating Pump (s): Yes/No (2) 3.4.1.14.1.3. Characteristics or make (s) and type (s) (if applicable): … … … … … … … … … … ….
3.4.1.14.1.4. drive ratio (s) (if applicable): … … … … … … … … … … ….
3.4.1.14.2. Air 3.4.1.14.2.1. Blower: Yes/No (2) 3.4.1.14.2.2. Characteristics or make (s) and type (s) (if applicable): … … … … … … ….
3.4.1.14.2.3. drive ratio (s) (if applicable): … … … … … … … … … … … ….
3.4.1.15. temperature permitted by the manufacturer: 3.4.1.15.1. Šķidrumdzes: maximum temperature at outlet: … … … … … … … … … … … … … … … …. 3.4.1.15.2. Air cooling: k milestone:.......................................................................... "
Maximum temperature at reference point: … … … … … … … … … … … … … … … … … … … … … ….
3.4.1.15.3. maximum charge air temperature at the intercooler outlet (if applicable): … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … …. K 3.4.1.15.4. maximum exhaust temperature at the exhaust pipe (FO), adhering to the exhaust manifold (s) (s) outer flange (s): … … … … … … … … … … … … … …. K 3.4.1.15.5. Lubricant temperature: minimum:................................... " K maksimālā: ............................................ K 3.4.1.16. Pressure charging device: Yes/No (2) 3.4.1.16.1. Mark: … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … ….
3.4.1.16.2. Tips: ...............................................................................................................
3.4.1.16.3. Description of the system (e.g. maximum charge pressure, waste-gate, if applicable): … … … … … … … … … … … … … … … … … … … … … … … … ….
3.4.1.16.4. Intercooler: Yes/No (2) 3.4.1.17. Intake system: maximum permissible inlet depression at rated engine speed and at 100% load:.................................................... kPa 3.4.1.18. Exhaust system: maximum permissible exhaust back pressure at rated engine speed and at 100% load: … … … … … … … … … … … kPa (37) 3.4.2. additional anti-pollution devices (if any, and if not covered by another heading) description and/or diagram (s): … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … ….
3.4.3. fuel feed 3.4.3.1. Feed pump pressure (37) or characteristic diagram:............................................................... kPa 3.4.3.2. Injection system pump 3.4.3.2.1.1 3.4.3.2.1.. Make (s): … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … ….
3.4.3.2.1.2. Tips(-i): .........................................................................................................
3.4.3.2.1.3. delivery: … … … … … … … … … and … … … … … … … … … …. (37) mm3 per stroke or cycle at pump speed of: … … … … … … … …. r/min (rated) and ... ... ... ... ... ... ... ... ... r/min (maximum torque) respectively, or characteristic diagram indicate the method used: on engine/on pump bench (2) 3.4.3.2.1.4. Injection advance 3.4.3.2.1.4.1. injection advance curve (37): … … … … … … … … … … … … … … ….
3.4.3.2.1.4.2. Timing (37): … … … … … … … … … … … … … … … … … … … … … … … … … … ….
3.4.3.2.2. injection piping length: 3.4.3.2.2.1................................................................................................... mm

4.5. Gearbox (type, direct engagement, method of control) (if any) 4.6. Gear ratios (if any) with or without the distribution kārbas73 gear ratio of the gearbox reduction ratio distribution boxes in the main transmission ratio overall ratio Variator maximum * minimum * Reversing Variator 1 2 3 1 note.
the continuously variable transmission (CVT).
 
4.6.1. maximum dimensions of tyres on the sum of the axes … … …. …. …. …. …. …. …. …. …. …. …. ….
4.7. Calculated maximum tractor design speed in most gear (specify calculation factors) 74 … … … … … … … … … … … … … … … … … … … … … … … … … … … km/h maximum speed measured on 4.6.1.................................................................... "km/h 4.8. actual straight-line motion distance corresponding to one full turn of the wheels driving........................................................................................................."
4.9. Speed Governor: Yes/nav75 4.9.1.................................................................................................................. "
4.10. Speedometer, tachometer and hour meter (if fitted) 4.10.1. Speedometer (if fitted) 4.10.1.1. Operating principle and the description of the drive mechanism … … … … … … … … … … … … ….
4.10.1.2. constant measuring apparatus. … … … … … … … … … … … … … … … … … … … … … … … … … … … ….
4.10.1.3. measuring apparatus, the permissible deviation........................................................................ "
4.10.1.4. Overall transmission ratio..................................................................... "
4.10.1.5. Measuring scales or other pointer design....................................................... "
4.10.1.6. Electrical/electronic components short description … … … … … … … … … … … … … … ….
4.10.2. Tachometer and hour meter (if fitted): Yes/nav76 4.11. Differential lock (if fitted): Yes/nav77 4.12. Power take-off (s) (revolutions per minute and ratio of the engine) (number, type, and location) 4. Main power take-off (s) … … … … … … … … … … … … … … … … … … … … … … … … … … … … ….
4.12.2. Citas .....................................................................................................................
4.12.3. Power take-off guard (s) (description, dimensions, drawings, photographs) … … … … … … … … … ….
4.13. engine components, projections and wheels (descriptions, drawings, sketches, photographs) protective surface One 4.13.1..................................................................................... "
4.13.2. More protective surface … … … … … … … … … … … … … … … … … … … … … … … … ….
4.13.3. protection with total encapsulation..................................................................... "
4.14. Brief description of the electrical/electronic components (if any)............................................. "
5. Asis
5.1. Katras ass apraksts ...................................................................................................
5.2. Marka (ja ir) .............................................................................................................
5.3. Tips (ja ir) .................................................................................................................
6. Suspension (where appropriate) 6.1. Extreme (minimum and maximum) tyre/wheel combinations (if any) (dimensions, characteristics, inflation pressure for road behaviour, wheel dimensions and front/rear combinations) …. …. …. …. …. …. …. …. …. …. …. …. …. …. …. …. …. …. …. …. …. …. …. …. …. ….
6.2. Each axle or wheel type of suspension (if fitted) …. …. …. …. …. …. …. …. …. …. …. …. …. …. ….
6.2.1. the height adjustment: Yes/No/after izvēles78 6.2.2. Brief description of the electrical/electronic components (if any)............................................ "
6.3. Citas ierīces (ja ir) ....................................................................................................
7. Steering (descriptive diagram) 7.1. Steering category: manual/servo/servo79 7.1.1. Reversible driving position (description) …. …. …. …. …. …. …. …. …. …. …. …. …. …. … … ….
7.2. Transmission and control 7.2.1. type of steering mechanism (point front and rear, if applicable)................................. "
7.2.2. The connection to the wheels (including other than mechanical one; points front and rear, if applicable).............................................................................................................. "
7.2.2.1. a brief description of the electrical/electronic components (if any).......................................... "
7.2.3. The amplification method (if any) …. …. …. …. …. …. …. …. …. …. …. …. …. …. …. …. …. …. …. ….
7.2.3.1. Method and diagram of operation, make (s) and type (s) … … … … … … … … … … … … … … ….
7.2.4. diagram of the steering equipment All the various devices in the vehicle, the location of which can affect the steering …. …. …. …. …. …. …. …. …. …. …. … … ….
7.2.5. The steering control (s) schematic diagram (s) … … … … … … … … … … … … … … … ….
7.2.6. The steering control adjustment range and method (if applicable) … … … … … … … … … ….
7.3. maximum turning angle of the wheels (if fitted) 7.3.1. To the right: … … … … … … … … … …. degrees. Number of turns of the steering wheel … … … … … … … … … ….
7.3.2. To the left: … … … … … … … … … …. degrees. Number of turns of the steering wheel …. …. …. …. …. …. …. ….
7.4. Minimum turning circle (without braking) 80 7.4.1............................................................................................................. "mm 7.4.2. Left......................................................................................................... mm 7.5. Steering method of adjustment (if applicable) … … … … … … … … … … … … … … … … … … ….
7.6. Brief description of the electrical/electronic components (if any).............................................. "
8. Brakes (kopskic and actions) 81 8.1. The service braking system............................................................................................... "

8.2. Secondary braking system (if fitted) … … … … … … … … … … … … … … … … … … … … … … … … … ….
8.3. Stāvbremze ...............................................................................................................
8.4. any papildbremž device (s) (and retarder).................................................... "
8.5. For vehicles with anti-lock brake systems-system (including any electronic parts), electric block diagram, hydraulic or pneumatic circuit plan................................................................................................................. "
8.6. the braking system components list with exact references....................................... "
8.7. the maximum tire size braked axles............................................. "
8.8. calculation of the braking system (determination of the ratio of the total braking forces at the circumference of the wheels and the force applied) …. …. …. …. …. …. …. …. …. …. …. …. …. … ….
8.9. The right and the left brake transmission lock. … … … … … … … … … … … … … … … ….
8.10. External energy source (s) (if any) (characteristics, capacity of energy reservoirs, maximum and minimum pressure, pressure gauge and minimum-pressure warning device on the dashboard, vacuum reservoirs and supply valve, supply compressors, compliance with provisions regarding pressure equipment): ... … …. …. …. …. …. …. …. …. …. …. ….
8.11. vehicles fitted with trailer braking devices 8.11.1. Trailer-brake actuating device (description, characteristics)............................. "
8.11.2. mechanical/hydraulic/pneumatic pievads82 8.11.3. Connectors, couplings, safety devices (description, drawing, sketch)........... "
8.11.4. Vienvad braking pievads83 interface or 8.11.4.1. Supply overpressure (1 line)................................................... kPa power 8.11.4.2. overpressure (2 line). … … … … … … … … … … … … … … … … … kPa 9. Field of vision, glazing, windscreen wipers and rear-view mirrors 9.1. The field of vision of 9.1.1. Drawing (s) or photograph (s) showing the position of parts in the forward field of vision …. …. …. …. …. …. …. …. …. …. …. …. …. …. …. …. …. …. …. ….
9.2. Glass 9.2.1. Necessary data reference point location for fast determination................. "
9.2.2. The windscreen (s) 9.2.2.1. Use (s) the material (s) …. …. …. …. …. …. …. …. …. …. …. …. …. …. …. …. …. …. …. ….
9.2.2.2. Montāžas metode ................................................................................................
9.2.2.3. Rake angle (s) … … … … … … … … … … … … … … … … … … … … … … … … … … … … …. degrees 9.2.2.4. EC component type-approval mark (s)........................................................ "
9.2.2.5. Windscreen accessories and their location and all of the electrical/electronic components short description … … … … … … … … … … … … … … … … … … … ….
9.2.3. Other window (s) 9.2.3.1. Location (s) …. …. …. …. …. …. …. …. …. …. …. …. …. …. …. …. …. …. …. …. …. …. ….
9.2.3.2. the Use (s) the material (s) … … … … … … … … … … … … … … … … … … … … … … … … … ….
9.2.3.3. EC component type-approval mark (s)........................................................ "
9.2.3.4. side glass of the brief description of the electrical/electronic components (if any) … … … … … … … … … … … … … … … … … … … … … … … … ….
9.3. windscreen wipers: Yes/nav84 (description, number, frequency of operation).................... "
9.4. Rear-view mirror (s) 9.4.1. Class (s) … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … ….
9.4.2. EC component type-approval mark (s)........................................................... "
9.4.3. position in relation to vehicle structure (drawings) …. …. …. …. …. … ….
9.4.4. The strengthening of the method (s) … … … … … … … … … … … … … … … … … … … … … … … … … … … ….
new item 9.4.5. Optional equipment that might restrict the field of vision of rear … … … … … … ….
9.4.6. The adjustment system brief description of the electrical/electronic components (if any).................................................................................................... "
9.5. Defrosting and demisting systems 9.5.1. Technical description of the device … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … ….
10. Roll-over protection device, protection against unfavourable weather, seats, load platforms 10.1. Roll-over protection device (dimensioned drawings, photographs (where appropriate), description) 10.1.1. frame (-ji) 10.1.1.0. Is/nav85. trade mark of 10.1.1.1 (s) … … … … … … … … … … … … … … … … … … … … … … … … … … ….
10.1.1.2. EC component type-approval mark (s)................................................... "
10.1.1.3. Internal and external dimensions................................................................................... "
10.1.1.4. material (s) and method of manufacture............................................................. "
10.1.2. Booth (s) Is/nav86 10.1.2.1.10.1.2.0. Trade mark (s).................................................................................. "
10.1.2.2. EC component type-approval mark (s)................................................... "
10.1.2.3. doors (number, dimensions, direction of opening, latches and hinges).............. "
10.1.2.4. Windows and emergency exit (s) (number, size, location) …. …. …. …. …. … … ….
10.1.2.5. Other devices for protection against unfavourable weather conditions (description) … … ….
10.1.2.6. Internal and external dimensions................................................................................... "
10.1.3. Roll-aizsarkonstrukcij (s) installed (s) front/aizmugurē87 drop (s) or drop (s) 88 of 10.1.3.0. Is/nav89 10.1.3.1. Description (position, fixing, etc.) … … … … … … … … … … … … … … … … ….
10.1.3.2. trade mark (s) or name (s) … … … … … … … … … … … … … … … … ….
10.1.3.3. EC component type-approval mark (s) … … … … … … … … … … … … … … … … ….

10.1.3.4. Izmēri ...............................................................................................................
10.1.3.5. material (s) and the type of construction … … … … … … … … … … … … … … … … … … … … … … … ….
10.2. Operating space and access to driving position (description, characteristics, dimensioned drawings).......................................................................................................................................... "
10.3. Seats and footrests 10.3.1. Driving seat (s) (drawings, photographs, description).............................................. "
10.3.1.1. trade mark (s) or name (s) … … … … … … … … … … … … … … … … ….
10.3.1.2. EC component type-approval mark (s)................................................... "
10.3.1.3. Seat type category: category A class I/II/III, (B) kategorija90 10.3.1.4. position and main parameters.............................................................. "
10.3.1.5. Regulēšanas sistēma .........................................................................................
10.3.1.6. Displacement and locking system … … … … … … … … … … … … … … … … … … … ….
10.3.2. passenger seats (number, dimensions, position and characteristics) … … … … … … … … … … … … … … … … … … … ….
10.3.3. Footrests (number, dimensions and location) … … … … … … … … … … … … … … … … ….
10.4. Kravas platforma
10.4.1. Izmēri .......................................................................................................... mm
10.4.2. Atrašanās vieta ....................................................................................................
10.4.3. Technically permissible load........................................................................... kg 10.4.4. Load distribution between the axles............................................................................ Suppression of radio interference suppression, kg 10.5 10.5.1. The engine compartment and adjacent parts of the passenger compartment of the part of the body of the description and drawings/photographs of the shapes and constituent materials of.............................................. "
10.5.2. The engine compartment contains a metal component (e.g. heating appliances, spare wheel, air filter, steering mechanism, etc.) drawings or photographs of the position of the.......................................................................................................................... "
10.5.3. Radio control devices list and drawings … … …. …. …. …. …. …. …. ….
10.5.4. Particulars of the nominal value of the direct current resistances, and, in the case of resistive ignition cables, of their nominal resistance per metre.......................................................... "
11. Lights and warning devices (vehicle body level, showing sketches of all the placement of lighting and light-signalling devices; number of electric scheme, EC type-approval mark and colour of lights) 11.1. Compulsory devices 11.1.1. Dipped-beam headlamps.......................................................................... "
11.1.2. Front position (side) lamp................................................... "
11.1.3. Rear position (side) lamp.................................................... "
11.1.4. Direction indicator lamps 11.1.4.1. front.......................................................................................................... "
11.1.4.2. pakaļējie ...........................................................................................................
11.1.4.3. sānu ..................................................................................................................
11.1.5. Pakaļējie atstarotāji ...............................................................................................
11.1.6. Rear registration plate lamp......................................................... "
11.1.7. Bremžu signāllukturi ...............................................................................................
11.1.8. Avārijas signālierīce ...............................................................................................
11.2. Optional devices 11.2.1. Main-beam headlamps.................................................................................... "
11.2.2. front fog lamps...................................................................................... "
11.2.3. Rear fog lamps … … … … … … … … … … … … … … … … … … … … … … … … … … … ….
11.2.4. Atpakaļgaitas lukturi ...........................................................................................
11.2.5. Darba lukturi ......................................................................................................
11.2.6. Stāvgaismas lukturi .............................................................................................
11.2.7. Kontūrgaismu lukturi ..........................................................................................
11.2.8. The trailer for tell-tale (s) … … … … … … … … … … … … … … … … … … … ….
11.3. The electrical/electronic components (if any), not the bulb, short description … … … … ….
12. Miscellaneous 12.1. Audible warning device (s) (position)............................................................... "
12.1.1. EC component type-approval mark (s) … … … … … … … … … … … … … … … … ….
12.2. The tractor and trailers of the mechanical coupling device for coupling devices 12.2.1. type (s) … … … … … … … … … … … … … … … … … … … … … … … … … … … … ….
12.2.2. the trade mark (s)..................................................................................... "
12.2.3. EC component type-approval mark (s) … … … … … … … … … … … … … … … … ….
12.2.4. Device designed for a maximum horizontal load of .......................................... kg, and for a maximum vertical load (if any) … … … … … … … … … … … … … … … … … … … … … …. kg91 12.3. Hydraulic lift-three-point coupling device: Yes/nav92 12.4. lighting and light-signalling devices on trailer connection site (description) … … … … … … … … ….
12.5. installation of the Control device, location, functioning and marking (description, photographs or diagrams) …. …. …. …. …. …. …. …. …. …. …. …. …. …. …. …. …. …. …. …. …. …. … ….
12.6. The rear number plate location (shape and size).............................. "

12.7. Front coupling device (dimensioned drawing)........................................................... "
12.8. The vehicle mounted or towed vehicle operation and the equipment used to control electronic devices...................................... "
13. Note 1 if a part has received type approval, it is not necessary to describe, if this is an indication of the type approval. The description is also required for all components of the design characteristics which are clearly indicated in charts or drawings will be added to a document. If you want to add photos or drawings, indicate the number of attachments for each position.
 2 delete as applicable.
 3 shall be classified having regard to Directive 2003/37/EC annex II, chapter A contains definitions.
 4 delete.
 5 delete.
 6 delete.
 7 delete.
 8 standards EN ISO 612:2005 "road vehicles – Motor vehicles and trailers sizes – terms and definitions" and EN ISO 1176 road vehicles: 2005 "– masses – dictionary and codes".
 the information requested on the presented 9 all possible variants.
10 assumes that the driver's weight is 75 kg.
11 information requested on the presented all possible variants.
12 Standard EN ISO 612/-6.4:2005 "road vehicles – Motor vehicles and trailers sizes – terms and definitions".
13 standard EN ISO 3746:2005 "agricultural tractors and machines-the distance between the wheels".
14 Standard EN ISO 612/-6.1:2005 "road vehicles – Motor vehicles and trailers sizes – terms and definitions".
15 Standard EN ISO 612/-6.2:2005 "road vehicles – Motor vehicles and trailers sizes – terms and definitions".
16 Standard EN ISO 612/-6:2005 "road vehicles – Motor vehicles and trailers sizes – terms and definitions".
17 Standard EN ISO 612/-6.6:2005 "road vehicles – Motor vehicles and trailers sizes – terms and definitions".
18 Standard EN ISO 612/-6.7:2005 "road vehicles – Motor vehicles and trailers sizes – terms and definitions".
19 Standard EN ISO 612/-6.7:2005 "road vehicles – Motor vehicles and trailers sizes – terms and definitions".
20 Standard EN ISO 612/-8:2005 "road vehicles – Motor vehicles and trailers sizes – terms and definitions".
21 Standard EN ISO 612/-6.1:2005 "road vehicles – Motor vehicles and trailers sizes – terms and definitions".
22 Standard EN ISO 612/-6.2:2005 "road vehicles – Motor vehicles and trailers sizes – terms and definitions".
23 Standard EN ISO 612/-6:2005 "road vehicles – Motor vehicles and trailers sizes – terms and definitions".
24 Standard EN ISO 612/-6.6:2005 "road vehicles – Motor vehicles and trailers sizes – terms and definitions".
25 Standard EN ISO 612/-6.7:2005 "road vehicles – Motor vehicles and trailers sizes – terms and definitions".
26 Standard EN ISO 612/-6.7:2005 "road vehicles – Motor vehicles and trailers sizes – terms and definitions".
27 Standard EN ISO 612/-8:2005 "road vehicles – Motor vehicles and trailers sizes – terms and definitions".
28 Standard EN ISO 612/-9:2005 "road vehicles – Motor vehicles and trailers sizes – terms and definitions".
29 Delete where inapplicable.
30 if the application more than one referred to in cilmdzinēj, shall be submitted for each specific form cilmdzinēj.
31 delete where inapplicable.
32 delete where inapplicable.
delete as 33.
34 delete where inapplicable.
35 delete.
36 delete.
37 point tolerance.
delete as 38.
delete as 39.
40 delete.
delete as 41.
42 point tolerance.
43 point tolerance.
delete as 44.
45 point tolerance.
46 point tolerance.
47 specify the tolerance.
delete as 48.
49 specifies the tolerance.
50 point tolerance.
51 point tolerance.
delete as 52.
53 if the application more than one referred to in cilmdzinēj, shall be submitted for each specific form cilmdzinēj.
delete as 54.
55 indicate tolerance.
delete as 56.
delete as 57.
delete as 58.
delete as 59.
delete as 60.
61 point tolerance.
62 point tolerance.
delete as 63.
64 point tolerance.
65 indicates the tolerance.
66 point tolerance.
67 point tolerance.
68 point tolerance.
69 point tolerance.
delete as 70.
delete as 71.
the information requested be submitted 72 for all possible variants.
73 the permissible deviation is 5%. Required to determine the measured speed not exceeding 43 km/h, with a tolerance of 3 km/h (see. Directive 98/89/EC).
74 the permissible deviation is 5%. Required to determine the measured speed not exceeding 43 km/h, with a tolerance of 3 km/h (see. Directive 98/89/EC).
delete as 75.
delete as 76.
delete as 77.
delete as 78.
delete as 79.
80 Standard EN ISO 789-3:2005 "agricultural tractors – test procedures – part 3: trimming, and clearance diameter."
81 for each braking device provides the following data: type and characteristics (sketch) (drums or discs etc., brake brake wheels, brake linkage of these wheels, friction surfaces, their properties and work surface area, drum pads, or drive the RADIUS, the brake drum weight and regulating devices), transmission and brake control (attach diagram) (construction, adjustment, lever rations, access control devices and their location mechanical transmission, functional leadership, the main parts of the transmission characteristics of the main brake cylinders and Pistons, brake cylinders).
delete as 82.
delete as 83.
delete as 84.
delete as 85.
delete as 86.
delete as 87.
delete as 88.
delete as 89.
delete as 90.
91 value relating to the mechanical strength of the coupling device.
delete as 92.
 
(B) a sample simplified information document for EC vehicle type-approval part I (1) (B) the use, if you have one or more EC type-approval or EC component type-approval certificates issued pursuant to the separate directives.
(2) the relevant EC type-approval or EC component type-approval certificate numbers indicates the model B in part III, in the table.

(3) the provisions of the information referred to in annex 3 (EC certificate of conformity) indicates in Chapter 1-12 for each vehicle type/variant/version.
(4) If in respect of any of the information in this annex the sample document that departments are not EC type-approval or EC component type-approval certificate issued pursuant to a separate directive, A model of the information document referred to in the information included in a same named model B Division.
0. General information 0.1. Make (s) (trade mark of the manufacturer) …. …. …. …. …. …. …. …. …. …. …. …. …. …. … ….
0.2. Type (specify any variants and versions) …. …. …. …. …. …. …. …. …. …. …. …. …. …. … … ….
0.2.0. Situation in terms of completeness: complete one stage/completed/not pabeigts1 0.2.1. If the vehicle is completed, indicate the previous name and address of the manufacturer and the incomplete or complete vehicle approval number. Trade name (s) (if applicable)................................................................................. "
0.3. means of identification of type, if marked on the vehicle 0.3.1. Manufacturer's plate (location and method of attachment)................................................ "
0.3.2. chassis number (location) …. …. …. …. …. …. …. …. …. …. …. …. …. …. …. …. …. …. ….
0.4. Category of vehicle..................................................................................... "
0.5. Name and address of the manufacturer................................................................................. "
0.7. in the case are components and separate technical unit, marks the location and method of affixing of the.......................................................................................................................................... "
0.8. Assembly plant (s) name (s) and address (s)............................................... "
1. General construction characteristics of the vehicle (added 3/4 front and 3/4 rear photographs or drawings of the prototype and the dimensional drawing of the whole vehicle scale);
2. Masses and dimensions;
3. Engine;
4. Transmission;
5. Axles;
6. Suspension;
7. Steering equipment;
8. the braking equipment;
9. Field of vision, glazing, windscreen wipers and rear-view mirrors;
10. Roll-over protection, protection against unfavourable weather, seats, load platform;
11. Lights and warning devices;
12. Miscellaneous.
Note the.
1 shall be classified, in the light of the provisions of chapter A of annex 1 contains definitions.
 
Part II (1) this part of the table referred to in paragraph 3 of part I of the model B summarizes above several points included components allow combinations of versions, if the combination are varied. For each of these components must receive a letter that identifies the table point or the point of the ingredient or ingredients that fit the specific version.
(2) a separate table shall be drawn up for each type of variant.
(3) several points components not subject to restrictions on its combination with some variation, the entry in the column "all versions".
 Point No.
 All versions of version 1 version 2 ... n (4) in the third paragraph of this part specified in the table information may be submitted in another format or layout, if one does not change the content of the information.
(5) each variant and version shall be identified with a numeric or alphanumeric code that records the vehicle EC certificate of conformity.
 
Part III EC type-approval numbers relating to the separate directives (1) Further information is provided about the characteristics that apply to the vehicle (the information contained in the certificate of approval, no need to repeat).
(2) in order to obtain the EC type-approval, all the relevant vehicle EC type-approval or component type-approval certificate (with their annexes) include the information folder and the EC type-approval authorities.
 Subject to the EC type-approval or EC component type-approval number of the EC type-approval or EC component type-approval date type (s), option (s), version (s) covered by the example of the braking equipment £ 1 * 76/432 * 97/54 * 0026 * 00 3.2.2000 MF/320/U £ 4 * 76/432 * 97/54 * 0039 * 00 1.3.2000 MF/320/F signature … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … ….
Amats......................................................................................................
Datums....................................................................................................
Minister of agriculture m. Roze Ministry of Agriculture presented the annex 3 of the Cabinet of Ministers of 27 June 2006 regulations no 535 EC conformity certificate (maximum format: A4 (210 mm × 297 mm) or a folder of A4 size.
The certificate shall be made out on the form so that a producer to turn off any possibility of falsification.
To this end, the certificates shall be printed on paper protected by means of colour graphics or by means of a watermark corresponding to the manufacturer's identification mark) in part I of the EC certificate of conformity the sample at one stage finished/completed vehicles(1) page 1 I, the undersigned,................................................................................................., (full name) hereby certifies that the vehicle: 0.1. Make (s) (registered by the manufacturer) …. …. …. …. …. …. …. …. …. …. …. …. …. …. …. …. … … ….
0.2. Type (specify any variants and versions) …. …. …. …. …. …. …. …. …. …. …. …. …. …. … … ….
0.2.1. Commercial name (s) (if applicable)....................................................................... "
0.3. means of identification of type, if marked on the vehicle............................... "
0.3.1. Manufacturer's plate (location and method of attachment)............................................... "
0.3.2. chassis number (location) …. …. …. …. …. …. …. …. …. …. …. …. …. …. …. …. …. …. ….
0.4. Category of vehicle..................................................................................... "
0.5. Name and address of the manufacturer................................................................................. "

3.2.1.7. Cylinder capacity … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … …. cm³ engine rated 3.6 effective jauda3 … … … … … … … … kW at … … … … … … … … …. min-1 3.6.1. Optional: PTO jauda3............................. kW at … … … … … … … … min-1 (rated speed PTO) (in accordance with OECD code 2 or standard EN ISO 789-1:2000 "agricultural tractors – test methods – Part 1: determination of the Capacity of the PTO") page 4 5. Transmission gearbox Ratios 4.5: front......................................................................................................................... "
Pakaļējie ..........................................................................................................................
4.7. Calculated maximum design speed … … … … … … … … … … … … … … … … km/h maximum speed measured on 4.6.1..................................................................... "km/h 7. Steering 7.1. Steering category: manual/servo/servo1 8. Braking (brief description of the braking device) … … … … … … … … … … … … … … … … … … … … ….
8.11.4.1. supply overpressure (vienvad)................................................... kPa 8.11.4.2. Overpressure in the transmission (interface to) … … … … … … … … … … … … … … … … … KPA 10. Roll-over protection, protection against unfavourable weather, seats, load platforms 10.1. Frame/kabīne1: Mark (s) … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … ….
EC type-approval mark (s)...................................................................................... "
10.1.3. Roll-over protection structure: front/drop-down/non nolaižamas1 aizmugurē1 Mark (s) … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … ….
EC type-approval mark (s)...................................................................................... "
10.3.2. Pasažiera(-u) sēdvieta(-as):
Skaits ..................................................................................................................
 
6. page 10.4. Load platform: 10.4.1........................................................................................................... mm 10.4.3. Technically permissible load............................................................................. light and 11 kg of signalling devices 11.2. Optional devices................................................................................................. "
 
12. Miscellaneous equipment tractor and trailer 12.2. mechanical coupling devices: 12.2.1. Type (s) … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … ….
12.2.2. Marka(-as) ..........................................................................................................
12.2.3. EC type-approval mark (s)......................................................................... "
12.2.4. maximum horizontal load … … … … … … … … … … … … … … … … … … … … … … …. kg maximum vertical load (if any).............................................................................. kg 12.3. Hydraulic lift-three-point coupling device: is/13. External nav1 sound level and number of the latest amendment, relating to the EC type-approval. If the directive is two or more application phases, indicate which phase.................................................................................................................................. "
13.1........................................................................................................... dB (A) 13.2. driving........................................................................................................ dB (A) 14. tangible sound driver līmenis3 and the number of the latest amendment, relating to the EC type-approval. If the directive is two or more application phases, indicate which phase................................................... DB(a) 15. emisija2 exhaust gas and the number of the latest amendment, relating to the EC type-approval. If the directive has two or more implementation stages, indicate which phase … … … … … … … … … … … … … … … … … … … … ….
15.1. Results of tests CO ... ... ... g/kWh particulate............ g/kWh HC ... ... g/kWh (x) Smoke … …. m-1 NOX … …. 7 g/kWh. page 15.2. Test results (if any) CO … …. CH4 g/kWh.......... g/kWh NOX ... ... g/kW particulates............ NMHC g/kWh …. 16 g/kWh. Fiscal power (s) (s) or class (-I) Italy …. …. …. …. …. …. …. ….
 Vācija ...................................
 Greece...........................
 Beļģija .............................
 Netherlands............................
 Portugal.........................
 Dānija ..............................
 Īrija .......................................
 Sweden.........................
 United Kingdom......... "
 Somija...................................
 Kipra  .............................
 Austria.............................
 Igaunija ................................
 Ungārija ..........................
 Čehija ................................
 Lietuva .................................
 Slovenia.........................
 Latvija ...............................
 Polija ....................................
 Slovakia.........................
 Malta .................................
 Spānija ..................................
  
 France.............................
 Luxembourg........................
  
 
17. Piebildes4 ...................................................................................................................
The notes.
1 Delete.
2 points at lower values.
3 indicate the test method used.
4, Inter alia, any information required for the fakultatīvaj areas or values that are mutually dependent on each other (in the case in point in the form of a table).
_____ _____ _____ _____ _____ _____ _____ _____ _____ _____ _____ _____ _____ _____ _____ _____ _____ _____ ____ 3rd page B-agricultural or forestry trailers-complete/in one stage 1 trailer pabeigtas1 General construction characteristics

Minimālā .........................................................................................................................
2.2.1. Interchangeable towed machinery technically permissible maximum (s) (s) complete (s) mass (s) according to the tyre specification: ... … … … … … … … … … … … … … … … … … … … ….
2.2.2. This (these) (s) of mass among the axles and, if there is a semi-trailer or centre-axle trailer, load on the coupling point: … … … … … … … … … … … … … … … … … … … … … … ….
2.2.3.1. masses (s) and tyre (s) axle.
Tyres (size) of dead weight technically permissible maximum mass on each axle, the maximum permissible vertical load on the coupling point of the coupling point 1 2 3 2.4.6. position: 2.4.6.1. height of the coupling point above ground: maximum 2.4.6.1.1................................................................................................. 2.4.6.1.2 mm minimum .............................................................................................. page 4 mm 2.4.6.2. Distance to the vertical plane passing through the axis of the rear axle.................... Garenbāze2 2.5 mm............................................................................................... mm 2.5.1.2. Distance between the Centre of coupling device and the rear of the semi-trailer............... mm 2.6. Minimum and maximum distance between the wheels … … … … … …/… … … … … … … mm2
2.7.1.1. Garums2................................................................................................ mm 2.7.1.1.1. Maximum permissible length of the completed vehicle..................... Platums2 mm the 2.7.1.2............................................................................................. mm 2.7.1.2.1. Maximum permissible width of the completed vehicle … … mm. Most 2.7.1.7 permissible Center deviation of gravity finished vehicle.................................................................................... mm 8. Braking (brief description of the braking system): no brake/independent braking system/inertia brakes/brake with 8.11.4.1. pastiprinātāju1 pressure overload in the transmission (vienvad)................................................... kPa 8.11.4.2. Overpressure in the transmission (to interface )..................................................... kPa 11. Lights and warning devices 11.2. Optional supplementary devices.................................................................................... "
 
12. Miscellaneous equipment and Tractor vehicle 12.2. mechanical coupling devices: 12.2.1. Type (s)............................................................................................................... "
12.2.2. Marka(-as) .........................................................................................................
12.2.3. EC type-approval mark (s)........................................................................ "
12.2.4. maximum horizontal load … … … … … … … … … … … … … … … … … … … … … … …. kg maximum vertical load (if any)............................................................................... "page 16.5 kg in the fiscal power (s) (s) or class (s) (if any) Italy …. …. …. …. …. …. …. ….
 Vācija ....................................
 Greece...........................
 Beļģija .............................
 Netherlands.............................
 Portugal.........................
 Dānija ..............................
 Īrija ........................................
 Sweden.........................
 United Kingdom......... "
 Somija.....................................
 Kipra ...............................
 Austria............................
 Igaunija ..................................
 Ungārija ..........................
 Čehija ...............................
 Lietuva ..................................
 Slovenia.........................
 Latvija ..............................
 Polija .....................................
 Slovakia.........................
 Malta ................................
 Spānija ...................................
  
 France............................
 Luxembourg.........................
  
 
17. Piebildes3 ...................................................................................................................
The notes.
1 Delete.
2 points at lower values.
3, Inter alia, any information required for the fakultatīvaj areas or values that are mutually dependent on each other (in the case in point in the form of a table).
Minister of agriculture m. Roze Ministry of Agriculture presented the annex 4 of the Cabinet of Ministers of 27 June 2006 regulations no 535 procedures to be followed by the multi-stage EC type-approval 1. for multi-stage EC type-approval process to be satisfactory, require concerted action from all interested producers. To this end, before granting EC type-approval on the first or the next stage EC type-approval authority shall ensure that the inspection and pointing to irregularities to the relevant manufacturers make production technical documentation that accurately represents the vehicle or its components (drawings, specifications), and technical information, described in the specification, and exchanges, thus providing a vehicle compliance with technical requirements specified in the relevant separate directives referred to this provision in chapter B of annex 2. This information includes data about the relevant system, component or separate technical unit EC type-approvals and of vehicle parts which are part of the incomplete vehicle but are not yet approved type.
2. in accordance with this annex to EC type-approval shall be granted on the basis of the type of vehicle to the current state of completion, and they include all the previous stage of EC type-approval.

3. Each manufacturer in a multi-stage EC type-approval process is responsible for the EC type-approval and conformity of production of all systems, components and separate technical units which it made or with whom it was supplemented by the results of the previous production stages. The manufacturer is not responsible for the systems, components or separate technical units which are type-approved in the previous stage, if he does not change the parts of the vehicle to such an extent that the previously granted type-approval becomes invalid.
4. If the application is submitted in accordance with the provisions of paragraph 9, the EC type-approval authority shall carry out the following procedure: 4.1 make sure that all approvals granted in accordance with the separate directives, satisfy the requirements of this directive;
4.2. ensure that all the data, taking into account the State of completion of the vehicle, should be included in the information folder;
4.3. when examining the documentation, make sure that the vehicle specification (s) and data contained in the vehicle information folder are included in part I of the information packet to the data or the EC type-approval certificates issued under the relevant separate directives and, in the case of the complete vehicle-if the point number in part I of the information folder is not included in any of the separate directives information package, confirm that the relevant part or parameter matches the data contained in the information folder;
4.4. carry out or arrange for the component and system testing of the vehicle to be type approved models, to verify that the vehicle (s) is (are) built in accordance with the relevant data appearing in the information package, the authenticity of which has been approved for all approvals granted pursuant to the separate directives;
4.5. If necessary, carry out or arrange for checks on the installation of separate technical units.
5. the number of vehicles to be inspected is adequate to this annex referred to in point 4.4. tests to check various combinations of separate technical units where type approval according to the degree of completeness and the following characteristics: 5.1 engine;
5.2. the gearbox;
5.3. powered axles (number, position, interconnection);
5.4. steered axles (number and position);
5.5. braked axles (number);
5.6. the roll-over protection structure.
6. Identifying the vehicle if it is made in several stages, each manufacturer shall affix to the vehicle a plate, in addition to the minimum manufacturer's plate fixed by the Council of 21 December 1988, Directive 89/173/EEC on the approximation of the laws of the Member States relating to certain components and characteristics of wheeled agricultural or forestry tractors. This plate securely attached to the visible and easily accessible location to the part that use does not need to change. On the plate must bear the following legible and indelible form to the information in the following order: 6.1. name of manufacturer;
6.2. EC type-approval number the first, third, and fourth part;
6.3. the EC type-approval;
6.4. the vehicle's serial number;
6.5. the maximum permissible laden mass;
4.1. maximum towable mass;
6.7. the combination of maximum permissible laden mass (if the vehicle may tow a trailer) (1);
6.8. maximum permissible mass on each axle, the list starting from front to aizmuguri1;
6.9. the maximum permissible vertical load on the coupling punktu1.
Note the.
1 point only if the value is changed in the EC type-approval stage.
Minister of agriculture m. Roze Ministry of Agriculture presented the annex 5 cabinet 27 June 2006 regulations no 535 under separate directives issued a list of the type-approval, the EC type-approval authority stamp list number … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … ….
Aptver laikposmu no ......................................... līdz ...........................................
For each period granted, refused or withdrawn EC type-approval provided the following information: manufacturer................................................................................................................ "
EC type-approval number: … … … … … … … … … … … … … … … … … … … … … … … ….
Marka ...................................................................................................................
Tips ......................................................................................................................
Izdošanas datums .................................................................................................
First date of issue (if the extended type approval certificate.................... "
Minister of agriculture m. Roze Ministry of Agriculture presented the annex 6 Cabinet 27 June 2006 regulations no 535 product compliance procedures i. initial assessment 1. before granting EC type-approval, the EC type-approval authority shall satisfy itself that the relevant measures and procedures in order to verify that the produced components, systems, separate technical units or vehicles to conform to the approved type.
2. the EC type-approval authority must make sure of this annex referred to in paragraph 1, the requirements for this purpose, the manufacturer provides technical documentation of production conformity of production control procedures and production and testing. Make sure the name of the Centre may be in other Member State of the European Union, the EC type-approval authority. The Authority satisfied about this annex referred to in paragraph 1, the requirements, prepare a statement of compliance in respect of the areas and production facilities it considered relevant to the product (s) receive type-approval.
 3. the EC type-approval authority shall accept the manufacturer's Declaration of conformity with the standard LVS EN ISO 9001:2001 "quality management systems-requirements" 7.3. point "customer satisfaction and continual development. The manufacturer shall provide the above standard quality system registration certificate of registration data and undertake to inform the EC type-approval authority of the registration, the period of validity or scope.

4. On receipt of a request from another Member State of the European Union EC type-approval authority, the EC type-approval authority shall without delay forward this annex referred to in paragraph 2, a statement of compliance or inform that it is unable to provide such notification.
II. Conformity of production 5. All vehicles, systems, components or separate technical units that have received type approval according to these rules must be made according to the type approved pursuant to the requirements laid down in these provisions.
6. When granting EC type-approval, the EC type-approval authority shall verify that measures have been taken and the checks provided for in this annex are laid down in the standards referred to in paragraph 3, and agreed with the manufacturer for each approval, with certain intervals to test, or equivalent tests, to ensure ongoing compliance with the approved type (including tests, where relevant, be carried out in accordance with these terms).
7. the EC type-approval holder: 7.1 ensure that should the procedures necessary for effective monitoring of products (vehicles, systems, components or separate technical units) conform to the EC type-approval;
7.2. to be available for testing equipment necessary for checking the conformity to each approved type;
7.3. ensure that test results are documented in protocols and they would be available for a period to be determined in agreement with the EC type-approval authority (not longer than 10 years);
7.4. all test results should be analysed to verify and with industrial production-specific tolerances ensure stability regarding parameters of the product;
7.5. ensure that for each type of the product is done at least in these regulations required checks and tests;
7.6. to provide additional sampling and repeat the test, if it turns out that a sample or test subject does not meet the requirements, as well as to take measures to restore the conformity of the corresponding production.
8. as regards the EC approval of this annex vehicle 7.5. the checks referred to in point boils down to making sure about the compliance with the specifications indicated in the EC type-approval.
9. EC type-approval authority may at any time make sure each production equipment the conformity control method applicable. The usual frequency of such verification correspond to the measures (if any) approved in accordance with this annex, paragraph 2 or 3, and provides relevant results of the review period that is appropriate for the EC type-approval authorities required the trust period.
10. Each test Checker displays the test records and production technological process description.
11. when testing the way it allows the Verifier random samples may be selected for testing in the manufacturer's laboratory (or testing laboratory). The minimum number of samples may be determined in the light of the results of the checks carried out by the manufacturer.
12. to ensure that, in accordance with paragraph 11 of this annex on the results of the tests, validity checker sample for testing laboratory, which carried out the EC type-approval tests.
13. Testing laboratory may be made to any of these rules or the test specified in the separate directives or test.
14. If the test results are not satisfactory, the manufacturer shall take all measures necessary to restore the product is in conformity with the approved vehicle type.
Minister of agriculture m. Roze Ministry of Agriculture presented in annex 7 versions of the Cabinet of Ministers of 27 June 2006 regulations no 535 quantity limitations A. Restrictions for small series no PO box
Category number of units (for each vehicle type) 1.
 T 150 2.
 (C) 50 3.
 R 75 4.
 S 50 b. restrictions end-of-series vehicles, 1. The maximum number of vehicles of one or more types of vehicles that you put into service in each Member State in accordance with the procedure laid down in this provision in paragraph 40, may not exceed 10% of the vehicles of all types, the number of the previous two years put in service in the Member State concerned and must not be less than 20.2. Vehicles put into service in accordance with paragraph 1 of this annex the procedures referred to in identified with particular reference to the certificate of conformity.
Minister of agriculture m. rose