Fertiliser And Substrate Identification, Quality, Conformity Assessment, And Trade Rules

Original Language Title: Mēslošanas līdzekļu un substrātu identifikācijas, kvalitātes atbilstības novērtēšanas un tirdzniecības noteikumi

Read the untranslated law here: https://www.vestnesis.lv/op/2015/179.5


Cabinet of Ministers Regulations No. 506 in 2015 (September 1. No 44 24) fertiliser and substrate identification, quality, conformity assessment, and trade rules Issued in accordance with the law of the movement of fertilizer in the first part of article 4, paragraph 1 of the i. General questions 1. determines: 1.1. fertilizers not marking "EC fertiliser", as well as the substrate: 1.1.1. identification, quality, compliance and marketing requirements; 1.1.2. registration conditions and procedures; 1.1.3. the permissible deviations from fertiliser and substrate quality declared; 1.1.4. the unwanted impurities maximum permissible concentration; 1.1.5. monitoring and control arrangements; 1.1.6. the supervision and control of the necessary quality conformity assessment procedures; 1.1.7. the requirements for the label, marking and packaging; 1.2. requirements for the declared plant fertilizer nutrient form, which is labelled "EC fertilizer"; 1.3. in accordance with the European Parliament and of the Council of 9 July 2008. Regulation (EC) no 764/2008 laying down procedures relating to the application of certain national technical rules to products lawfully marketed in another Member State and repealing Decision No 3052/95/EC, Latvia imported fertiliser and substrate (hereinafter notified fertiliser and substrate) the notification and submission of documents, the unwanted impurities maximum concentration , monitoring and control procedures, as well as quality conformity assessment procedures for monitoring and control purposes; 1.4. the granting of authorisation procedures for fertilizers and substrates for marketing or importation, which are not included in the crop monitoring information system of national fertiliser and substrate in the national register (hereinafter register) or which do not correspond to the declared quality or quality and identification requirements.
2. Animal organic fertiliser and substrate movement shall take place in accordance with the legislation on veterinary requirements of animal by-products and processed products, not intended for use in food, as well as the European Parliament and of the Council of 21 October 2009. Regulation (EC) no 1069/2009 laying down health rules as regards animal by-products and derived products not intended for human consumption and repealing Regulation (EC) No 1774/2002 (hereinafter Regulation No 1069/2009), and the European Commission on 25 February 2011 Regulation (EU) No 142/2011, implementing European Parliament and Council Regulation (EC) no 1069/2009 laying down health rules as regards animal by-products and derived products not intended for human consumption and Council Directive 97/78/EC with regard to certain practices and goods which are not on the border veterinary checks carried out under that directive (hereinafter Regulation No 142/2011).
II. the fertiliser and substrate applicable identification, quality and trade requirements 3. Fertilizer and substrate identification and applicable quality requirements, as well as the declared quality indicators are defined in annex 1 of these rules. 4. The fertiliser and substrate declared quality meeting the requirements of this regulation, if a specific performance indicator in the negative deviation does not exceed the provisions mentioned in annex 2.
5. quality score are not permitted deviations from these rules referred to in annex 1 minimum and maximum numeric values, except the H section fertilizers. 6. If this rule is not specified in the annex, in particular the maximum plant fertilizer nutrient content fertilizer allowed it to increase more than the declared content. If this provision is specified in annex 1 for the maximum plant fertilizer nutrient content, increasing the fertilizer it is limited to the provisions listed in annex 1 to the maximum. 7. Unwanted impurity concentration in the fertilizer and the substrate should not exceed the maximum permissible concentration (annex 3). 8. the declared minimum trace-element content of the fertilizer is specified in annex 4 of these rules. 9. Laboratory accredited national accreditation body according to the laws and regulations on assessment of conformity assessment bodies, accreditation and supervision or in another Member State of the European Union or European economic area national accreditation body (hereinafter referred to as the accredited laboratory), issue a test report for fertiliser and substrate. Test report on viable micro-organisms preparations microbiological and biological active compounds in the plant growth promoters may be issued a scientific institution, which according to the law of scientific activity is registered in the register of scientific institutions, or another Member State of the European Union officially registered scientific institutions. 10. the Accredited laboratory of the fertiliser tested in accordance with European Parliament and Council of 13 October 2003 Regulation (EC) No 2003/2003 relating to fertilisers (hereinafter Regulation No 2003/2003) the following methods. If the test method Regulation No 2003/2003 is not specified, the fertilizer may be tested in accordance with the Ministry of Agriculture recommended standards applicable to national standardisation body shall publish in its tīmekļvietn (URwww.lvs.lv).
11. test the expenses related to the fertilizer or the registration or their introduction into the substrate or marketing authorisation, shall be borne by the manufacturer or importer. 12. The fertiliser and substrate manufacturer, Packer, importer or dealer wholesale and retail site: 12.1 State plant protection service (hereinafter service) request, fertiliser and substrate of the accounting records and supporting documents as well as information on fertiliser and substrate movement; 12.2. ensure fertiliser and substrate storage conditions according to the label, the label or in an accompanying document, and the safety data sheet (if any).
III. The fertiliser and substrate registration 13. Fertilisers and substrates are recorded in the relevant registers and manages the service. 14. the application of fertilizer or substrate for registration shall submit the legal or physical person who manufactured, packaged or imported fertiliser and substrate or preparing a mixture of fertilizers (except mixtures in accordance with specific agreements made by individual order the end user) (hereinafter person). If fertilizer or substrate are recorded by the manufacturer, it may be freely imported.
15. To register a fertilizer or substrate, a person shall submit to the Department: 15.1. submission (annex 5); 15.2. the manufacturer or importer-accredited laboratory test reports issued (Member State of the European Union and European economic area country produced fertilizer and the substrate may submit a test report issued by the manufacturer), turn on biologically active compounds of the plant growth promoters and viable micro-organisms the microbiological preparations may submit a test report issued by the scientific institution, which according to the law of scientific activity is registered in the register of scientific institutions , or another Member State of the European Union officially registered scientific institutions. Test report submitted for registration are not older than 12 months; 15.3. Packer, or substrate fertilizer registration certificate copy; 15.4. the rules referred to in point 13.3. requirements for the issue of scientific institutions (annex 6) that the typical fertilizer, plant growth promoter or microbiological preparations gave positive results of the effectiveness of the fertilizer. Opinion indicates crop used in the trial; 9.6. labels, label or accompanying document text with the information in the Latvian language in accordance with the provisions of paragraph 52 – fertilizer (other than microbiological preparations), in accordance with the provisions of paragraph 53-microbiological preparation and in accordance with paragraph 54 of these regulations – substrate; 15.6. a test report (a copy) of the detonation safety of ammonium nitrate fertilisers with a nitrogen content exceeding 28 percent; 15.7. the safety data sheet, if the European Parliament and of the Council of 18 December 2006, Regulation (EC) No 1907/2006 concerning the registration, evaluation, authorisation and restriction of chemicals (REACH), establishing a European Chemicals Agency, amending Directive 1999/45/EC and repealing Council Regulation (EEC) No 793/93 and Commission Regulation (EC) No 1488/94 as well as Council Directive 76/769/EEC and Commission directives 91/155/EEC , Directive 93/67/EEC, 93/105/EC and 2000/21/EC; 15.8. the planned list of point of sale; 15.9. information on the assigned registration or recognition of the official number, and a reference to the tīmekļvietn of the competent institution, which contains information that the fertilizer or the manufacturer of the substrate is recognized or registered pursuant to Regulation No 1069/2009, if fertilizer or substrate containing animal by-products or derived products not intended for human consumption (animal by-products); 15.10. the manufacturer's written permission of microbiological preparations repackaged, if it is intended to do. 16. to register in the preparation of mechanical mixtures of fertilisers, the person shall: 16.1 the Services application (annex 7); 16.2. the mechanical mixture of a production copy of the technical description (except packaging); 16.3. test review copy for detonation safety feature where the fertiliser ammonium nitrate nitrogen content exceeding 28 percent of the fertiliser by mass; 16.4. the Blender mixture for that motor blend made from the registered fertilisers or of fertilisers that are marked "EC fertiliser", and that not registered therein component (if any) does not exceed 0.5% of the total mass (the Packager shall submit a copy of the registration certificate of the mixture); 16.5. labels, label or accompanying document sample text with the information in the Latvian language in accordance with the provisions of paragraph 52; 16.6. the planned list of point of sale.
17. The Registrar is responsible for these rules 15 and 16 of the document referred to in paragraph 1. 18. Department of applied fertilizers or compliance with this provision of the substrate identification, quality and marketing requirements begin to consider after you have completely filled in all 15 of these rules or the documents referred to in paragraph 16. 19. in order to make a decision about the fertilizer or substrate, service, stating its reasons, may require the person to call for further information, as well as the appropriate qualifications of experts. 20. If by the end of the statutory period is not presented this rule 19, paragraph information, service application rejected. 21. the service within one month of the 15 and 16 of the rules referred to in point of receipt of documents shall take a decision to register a fertilizer or substrate, if the following conditions are met: 21.1. it complies with these rules 1 and 3 referred to in annex quality requirements; 21.2. labels, label or accompanying document sample meets the requirements of this regulation; 21.3. ammonium nitrate fertilizer with nitrogen content exceeding 28 percent, has made the detonation test according to Regulation No. 2003/2003 specified methods and fertilizer is recognized as sprādziendroš; 21.4. atypical of a fertiliser plant growth promoters or microbiological preparations (other than microbiological preparations are offered only as a composter) have received positive test results for the fertilizer effectiveness check, if the trial is conducted in area A or B in accordance with the European Parliament and of the Council of 21 October 2009. Regulation (EC) No 1107/2009 concerning the placing of plant protection products on the market and repealing Council Directives 79/117/EEC and 91/414/EEC , or in third countries similar latitudes and it has made a scientific institution, which according to the law of scientific activity is registered in the register of scientific institutions, or other government institution that is registered in the register of scientific institutions in accordance with national legislation; 21.5. atypical fertilizer, plant growth promoter or microbiological preparations for trial, where the only difference in compliance with principle and who performed with field crops in the last 10 years, at least two years in a row, but with cover crops of the area, at least two consecutive harvest cycles, the period under examination are given an average of at least 10 percent yields growth (except for decorative plants). The fertilizer label indicates their crop or crop group for which a positive result of the test of effectiveness; 21.6. State fee has been paid in accordance with the laws of the State fee for fertiliser and substrate registration or authorization of fertiliser and substrate for import or trade. 22. paragraph 21 of these rules If the conditions are not met, the Department shall take a decision on the refusal to register a fertilizer or substrate.
23. the service: 23.1. within three working days after the decision shall inform the person in writing; 23.2. If this provision is adopted, paragraph 21 of the decision: 23.2.1. entry shall be made in the register, including all the data referred to in the application, as well as information on the fertiliser and substrate quality indicators and declared the fertilizers (except the microbiological preparations) the essential composition; 23.2.2. within 10 working days, issue the person a certificate of registration, certifying that the fertilizer or substrate is included in the register. 24. the marketing authorisation holder shall be responsible for substrate of the fertiliser and compliance with the requirements set out in the legislation on fertilisers and chemicals and products, animal by-products, as well as compliance with Regulation No 1069/2009 and Regulation No 142/2011 requirements.
25. Fertilizers (except the microbiological preparations) shall indicate in the certificate of registration information in accordance with the provisions of Annex 8, the microbiological preparation in the registration certificate, in accordance with the provisions of Annex 9 and substrate in the registration certificate, in accordance with the provisions of annex 10.
26. the holder of the registration certificate within 10 days notify the Department in writing of the amendments resulting from the registration of the documents submitted.
27. Amendments to the register made after service of the decision, adopted on the basis of the owner of the certificate of registration of the application and the attached documents. The holder of the registration certificate shall indicate in the application the reasons for the amendment. 28. following the amendment of the register (if you change the data of the registration certificate) service shall issue a new certificate of registration with the same registration number and reverses the previous registration certificate. 29. the service two weeks withdrawn or substrate fertilizer registration and certificate of registration if the person registering a fertiliser or substrate, has provided false information or in accordance with the law of the movement of fertilizer in the first paragraph of article 11. 30. the decision on the fertiliser and substrate registration and cancellation of registration certificate service will be published in the Official Gazette "Latvijas journal". Void fertilizers stock trading network can be three years after the publication of the decision, if they are not dangerous to human and animal health and the environment.
31. The fertiliser and substrate's label, the label and the accompanying document uses "organic farming" or "authorised for use in organic farming", if the legislation on the organic agriculture of the supervision and control of specific control authority (hereinafter referred to as the control authority) issued the certificate with proof of compliance with labelling of fertilisers or labelling with the indication "organic farming" or "authorised for use in organic farming".
32. Certificate with proof of compliance with labelling of fertilisers or labelling with the indication "organic farming" or "authorised for use in organic farming" control body shall be issued in accordance with the legislation on the organic agriculture supervision and control. Control authority within five working days after the certificate is issued with a receipt, notify the Department.
33. the service within five working days after the fertiliser and substrate on its tīmekļvietn for registration information for the registered fertilizer or substrate-name (trade name), personnel (other than microbiological preparation and substrate), raw materials (only substrate), the name of the person or name that registers the corresponding fertiliser or substrate, the name of the manufacturer and the country, the number of the registration certificate, the fertilizer or the chain of the substrate and the indication "organic farming" or "authorised for use in organic farming" If the requirements of this regulation for the appropriate indications.
IV. The fertiliser and substrate notification procedures 34. Latvia traded To notify fertiliser or substrate, the importer or the manufacturer no later than 20 working days prior to the fertiliser and substrate a first deployment of the Latvian market service provided: 34.1. submission (annex 11); 21.3. the competent national authorities or the receipt issued by the manufacturer, such as a copy of the registration certificate, if in accordance with national laws and regulations are issued by the manufacturer this receipt or supporting this fact from the public prints of these fertilizers or of the Member State of registry, the substrate or any other evidence proving the fertilizer or the substrate legitimate trade in the Member States of the European Union, European economic area Member State or in Turkey; 21.3. labels, label or accompanying document of the Latvian language in the text, the content of which corresponds to the text in the language of the country, which is recognised by the fertiliser and substrate. If the application is submitted in paper form, the applicant the label or labelling shall also be submitted in electronic form; 21.4. information about organic fertiliser and substrate materials; 34.5. information about organic fertiliser and substrate, if it contains animal by-products, showing the assigned registration or recognition of the official number, as well as the competent institution tīmekļvietn, which contains information that the organic fertilizer and substrate manufacturers have recognised or registered pursuant to Regulation (EC) no 1069/2009. 35. Expenses associated with the notification and fertilisers into the substrate, the importer or the manufacturer in the list shall cover, in accordance with the regulations on professional fees provided by the services price list. 36. the service 20 working days after the rules referred to in paragraph 34 of document receipt shall take a decision on the notified or substrate fertilizer records, including the fertiliser and substrate in the list. Service in its tīmekļvietn on the fertilizer or the substrate indicates the type and trade name, manufacturer, the applicant, the Member State which it acknowledged receipt of the Member State concerned, and the date and number (if any), as well as the period of validity of the certificate (if one is specified) and the date of recognition in Latvia. 37. The notified fertilizers and substrates relate this rule 42, 43, 44, 45 and 46. the requirements referred to in paragraph. 38. If the notified fertiliser and substrate containing animal by-products, the service after receipt of the application, inform the food and veterinary service. 39. If the Department determines that the unwanted impurities concentration notified the fertilizer or the substrate exceeds the maximum levels in accordance with the provisions of this annex, it shall contact the competent authority of the Member State concerned to obtain information on national law certain unwanted impurity concentration. If the laws of the Member State concerned in a given concentration is exceeded or is found in fertilizer or substrate hazard to the environment, human or animal health service act in accordance with the laws of movement of fertilizers and article 9 of the second paragraph, the procedure laid down in paragraph 3, as well as a fertilizer shall be deleted from the list of recognised fertilizers.
V. monitoring and control 40. According to the legislation on fertilisers and substrates control sampling and preparation procedures take fertiliser and substrate control sample and submit it to the accredited laboratory to determine the number of viable micro-organisms preparations microbiological or biologically active compounds content of plant growth promoter. Control samples may also be made in paragraph 9 of these regulations in that a scientific institution. 41. According to the legislation on fertilisers and substrates control sampling and preparation procedures having notified the fertiliser and substrate control sample and submit it to the accredited laboratory to determine the unwanted impurities in the maximum levels. 42. The accredited laboratory or scientific authority with staff writing coherent term passes then the fertilizer or the substrate identification and testing quality indicators report. 43. the service based on accredited laboratories or scientific institutions the issued test report includes these provisions concerned these indicators, evaluate the fertilizer or the substrate quality control sample compliance with this rule or Regulation No 2003/2003. If the fertilizer or the quality of the substrate matches the specified requirements, control expenses of the following objectives for the national budget.
44. If the fertilizer or the substrate quality does not meet the requirements of this regulation, the Department within 10 working days, send to the laboratory accredited or the appropriate scientific institution in the other fertilizers or substrate control sample. The second control in the sample test only those fertilizers or substrate quality indicators, which have been found. If the second sample also shows the control of fertilizers or substrate quality non-compliance with requirements of this regulation, service by the person and relevant qualifications of the expert to assess the possibility of amendments in the register or taken a decision on the fertilizer or the substrate of registration and cancellation of registration certificate.
45. If, in accordance with the repeated test report of fertilizer or substrate quality does not meet the requirements of this regulation, all the control sample testing costs shall be borne by the person concerned or of the substrate fertilizer produced, imported, packaged for sale, trade or prepared fertilizer mixtures. 46. If the service finds the fertilizer or the substrate quality, it five working days, inform that person of the expenditure connected with the testing of the control sample, and their payment arrangements.
47. If the Department finds that the notified fertilizer or substrate may be harmful to human and animal health and the environment, that five working days shall inform in writing the Ministry of Agriculture.
48. Ministry of agriculture examined this provision the information referred to in paragraph 47 and, if necessary, inform the European Commission and the other Member States.
49. a Person may be imported without authorisation does not register the substrate fertilizer or non-commercial purposes (for personal use), if fertilizer or substrate, a person coming from third countries do not apply import and its value exceeds the amount set in the legislation on the exemption from value added tax.
50. If the inspection body shall inform the staff that the fertilizer or the substrate does not meet the requirements of organic farming, service: 50.1. Decides on the fertilizer or the suspension of trading in the substrate to failures; 50.2. delete registered fertilisers and substrates in the list of "organic farming", or "for use in organic farming".
Vi. Requirements and substrate fertilizer label, marking and packaging 51. Information on the fertiliser and substrate indicated the fertilizer or the substrate packaging or label, but the label bulk fertilisers and substrates – accompanying document. If the fertiliser and substrate packaging mass exceeding 25 kilogrammes, fertiliser or substrate language in Latvian, according the requirements of these regulations may specify the fertilizer in the accompanying document. If microbiological preparation and fertilizer that has "organic agriculture" and "authorised for use in organic farming", has more than 25 kilograms heavy packages, information on the label or labeling.
52. Fertilizers (except the microbiological preparations), the label of the packaging label or in an accompanying document required information appearing in this provision are listed in annex 12. 53. Microbiological preparations the packaging label or labelling information appearing in this provision are listed in annex 13. 54. Substrate packaging or labelling the label information appearing in this provision are listed in annex 14. 55. The fertiliser and substrate submitted for registration label or marking, the text of which was filed or substrate fertilizer for registration, located on the packaging clearly visible and clearly separate from any other information which may not be in conflict with the label or the label of the submitted text. 56. the packaging of fertilisers closed so as to when you open it, is completely damaged fastening fastening seal or the container itself. 57. the information label or the label is in the Latvian language and clearly legible. 58. the label or the label is resistant to external influence. 59. The fertiliser and substrate manufacturer, Packager and importer and fertilizer mixture Blender supports: 59.1. fertilizer or substrate packaging reliability and safety to keep the fertilizer or the quality of the substrate; 59.2. ammonium nitrate fertiliser of high nitrogen content (more than 28 percent), and the only trace of liquid fertilizers containing hard fertilizer supplies for sale to the final consumer in packaged form. 60. Microbiological preparation course may only be on the manufacturer's packaging or, where the service is supplied to the manufacturer's written permission, including the repackaged Packer package. 61. The fertiliser and substrate registrant or consent holder is responsible for the label specified in the label and the accompanying document information.
VII. Authorization procedures for fertilizers and substrates for sale or importation, not recorded in the register or which do not correspond to the declared quality or quality requirements, or requirements identification service issued the following 62. permits (annex 15) fertiliser and substrate for sale or importation: 62.1. permissions and substrate fertilizer for import testing and registration; 62.2. authorisation for the fertiliser and substrate for import or trade that is not mentioned in annex 1 of these rules; 38.7. permission registered and substrate fertilizer trade, if test results show a mismatch in the register of declared quality; 38.8. permission for testing and registration of imported fertiliser and substrate of the batch concerned trade; 62.5. authorisations shall not be established for the importation of fertilizer efficiency tests and studies; 38.9. permission registered fertilizer specific for the import and marketing of the party if the fertiliser batch does not comply with the rules referred to in annex 1 of the quality requirements.
63. in order to receive a permit, submit an application service (annex 16) and the relevant documents in accordance with these rules, 67, 65, 69, 71, 73 and 75, paragraph. 64. the fertiliser and substrate into testing and registration, provided the fertiliser and substrate are mentioned in annex 1 of these provisions, but not registered. 65. for these rules permit referred to in paragraph 64, the fertiliser and substrate, the manufacturer or importer shall submit to the Department: 65.1. test report issued by the manufacturer or its copy; 65.2. test of resistance to detonation or a copy of the ammonium nitrate fertilisers of high nitrogen content exceeding 28 percent; 65.3. information on imported fertiliser and substrate storage space to its testing and completion of the registration, indicating the actual address; 65.4. information on the fertiliser and substrate. 66. Authorisation for the fertiliser and substrate for import or trade that is not mentioned in annex 1 of these regulations, shall be issued, if the fertiliser and substrate does not meet the requirements of this regulation, but is not dangerous to human and animal health and the environment. 67. for these rules permit referred to in paragraph 66, the fertiliser and substrate, the manufacturer or importer shall submit to the Department: 67.1. a test report issued by the manufacturer (if the fertiliser and substrate manufactured in a Member State of the European Union and European economic area country) or accredited laboratory test report contains the unwanted impurities content according to annex 3 of these rules; 67.2. a copy of the test report on the detonation safety of ammonium nitrate fertilisers with a nitrogen content exceeding 28 percent; 67.3. labels or markings with the sample text information for Latvian language in accordance with the provisions of paragraph 52 or 54.; 41.9. list of points of sale.
68. the authorisation shall be registered and substrate fertilizer trade, if test results show a discrepancy in the quality of the register shall issue declared provided that junk is not exceeded the maximum level of impurities. 69. for these rules permit referred to in paragraph 68, the person shall provide the services: 69.1. the labels, label or accompanying document sample text that contains fertilisers and substrates in actual quality indicators; EB 69.2. information on the fertiliser and substrate batch number and the quantity.
70. the permission for testing and registration for imported fertiliser and substrate of the batch concerned trade issue accredited laboratory test results show a fertiliser and substrate non-compliance with these rules referred to in annex 1 quality requirements, but dangerous impurities does not exceed the maximum of undesirable impurities levels. 71. for the provisions referred to in paragraph 70, fertiliser and substrate, the manufacturer or importer shall submit to the Department: 71.1. laboratory accredited test reports issued which contains the unwanted impurities content according to annex 3 of these rules; 71.2. imported fertiliser and substrate lot number and quantity; 71.3. labels or markings with the sample text information for Latvian language in accordance with the provisions of paragraph 52 or 54.; 71.4. list of points of sale. 72. the authorization shall be established for the importation of fertilizer efficiency trials and studies shall be issued, if fertilizer is not registered and not dangerous to human and animal health and the environment. 73. for these rules permit referred to in paragraph 72, the fertilizer manufacturer or importer shall submit to the Department: 73.1. test report issued by the manufacturer (if the fertilizer produced in the Member State of the European Union and European economic area country) or accredited laboratories of the issued test report contains the unwanted impurities content according to annex 3 of these rules; 73.2. copy testing report for the detonation safety of ammonium nitrate fertilisers with a nitrogen content exceeding 28 percent; 73.3. information about the test and study of place, time, and by whom, the quantity of fertilizer trials and research objectives. 74. the authorisation shall be registered for a particular batch of fertilizer importation and marketing of fertilizer if the party does not comply with the rules referred to in annex 1 quality, shall be issued, if fertilizer is not dangerous to human and animal health and the environment. 75. for these rules permit referred to in paragraph 74, the fertilizer manufacturer or importer shall provide the services of accredited laboratories: 75.1. the issue of the test report contains the unwanted impurities content according to annex 3 of these rules; 75.2. the test report (a copy) of the detonation safety of ammonium nitrate fertilisers with a nitrogen content exceeding 28 percent; 75.3. the lot number of the fertilizer and the quantity; the label or marking 75.4. sample text with the information in the Latvian language in accordance with the provisions of paragraph 52; 75.5. the marketing list. 76. the service within 15 working days after all this rule 65, 67, 69, 71, 73 and 75, paragraph of receipt of documents shall take a decision on the permit concerned. Import licences shall be valid for 18 months. 65. These provisions permit referred to in paragraph 1 shall be valid for three months. 77. If fertilizer or substrate is dangerous to human and animal health and the environment, the Department decides not to issue a permit.
78. The permit holder shall be responsible for the fertiliser and substrate in compliance with permit declared the quality indicators. 79. the service within five working days after the fertiliser and substrate permit on its tīmekļvietn for fertiliser and substrate authorisation – the fertiliser and substrate name, composition (other than microbiological preparation and substrate), raw materials (only substrate), the recipient of the permit, the permit number of the manufacturer, the date of issue and term of validity. VIII. concluding issues 80. Be declared unenforceable in the Cabinet of 27 June 2006, Regulation No 530 "identification of fertilizers, quality, conformity assessment, and trade rules" (Latvian journal, 2006, nr. 101.; 2008, 100. no; 2009, nr. 57.198. No; 2011; in 2012, no 83.).
81. By 2016 January 1 medium to market without registration and authorisation. 82. This provision of the annex 12 6 requirements referred to in paragraph shall enter into force on January 1, 2016. 83. the requirements of this regulation for the number of the registration certificate or permit number of the label, the label or in an accompanying document shall enter into force on January 1, 2017. 84. Until 2017 January 1 worm fertilizer for organic processed do not apply these rules to 15.9. referred to in the claim. 85. The people up to the date of entry into force of the provisions has registered processed organic worm fertilizer containing animal material until 2017 January 1, submit to the Department the information that earthworms for the processing of animal by-products and derived products not intended for human consumption, including manure, processed in accordance with Regulation No 1069/2009. If the information is not submitted to the Department until 2017 January 1, service after January 1, 2017. the cancelled earthworm processed organic fertilizers. 86. The rules referred to in paragraph 8.5. requirement for substrates and paragraph 35 of these regulations shall enter into force on January 1, 2016. The Prime Minister is the Rapidity of the farming Minister Newsletters John Dūklav annex 1 Cabinet 1 September 2015 regulations no 506 fertiliser identification requirements a. ordinary (major plant nutrient-containing) fertilizers of nitrogen fertilizers in No 1. p. k. The official name of the fertilizer production method, the basic quality requirements (plant nutrient minimum content (% by weight of the fertilizer), and applicable to the specific fertilizer) fertilizer, label or accompanying document must be declared on the labelling of quality indicators (%) and other requirements 1. Ammonium nitrate (nitrate) For chemically, as – ammonium nitrate can contain additives – minced, minced limestone dolomite, calcium sulphate, magnesium sulphate, kizerīt 20% of the total nitrogen (N). Nitrate and ammonium nitrogen each represent about half of the total nitrogen. Ammonium nitrate can contain additives: calcium carbonate (limestone) or magnesium and calcium carbonate (dolomite). Specific requirements: where fertilizers contain more than 28% N, they must meet the following additional requirements (% by mass): a) they must not contain inorganic additives or inert substances, other (other than above), which can increase the heating or the risk of explosion, as well as heavy metals and any process in the manufacture of a quantity must not increase product heating or explosion; b) fertilizers, which must first have undergone two thermal cycles of 25-50 ° C, oil retention does not exceed 4% of their weight; c) flammable components, expressed in the form of carbon, not exceeding (percentage by mass): 0.2%-fertilizers, containing not less than 0.4% 31.5% of nitrogen-fertilizers containing 28-31,4% nitrogen; d) ammonium nitrate solution (10 g ammonium nitrate dissolved in 100 ml of water) a pH of not less than 4.5; (e) not more than 5%) of the particles pass through a sieve with a mesh size of 1 mm and not more than 3% – through a sieve, which size is 0.5 mm; f) chlorine content not exceeding 0.02% of the mass of ammonium nitrate; g) copper content (hlorūdeņražskāb, density at 20 ºc: 1.18 g/ml) not more than 10 mg/kg of total nitrogen (N), nitrate nitrogen (NO3-N), ammoniacal nitrogen (N-NH4) 2. Calcium nitrate derived chemical, as – calcium nitrate and ammonium nitrate, 15% of the total nitrogen (N). Nitrogen is nitrate (N-NO3) and ammonium (N-NH4) of nitrogen form. Maximum of ammoniacal nitrogen content-1.5% N total nitrogen (N). Additional parts (if required): nitrate nitrogen (N-NO3) and ammonium (N-NH4) nitrogen, calcium (Ca) 3. Calcium-magnesium nitrate is obtained chemically, as – calcium nitrate and magnesium nitrate 13% nitrate nitrogen (N), 3 .0% water soluble magnesium (Mg) of nitrate nitrogen (NO3-N), water soluble magnesium (Mg) 4. Magnesium nitrate is obtained chemically, as 10% of magnesium nitrate-nitrate nitrogen (N), 8 3% water soluble magnesium (Mg). If Mg is a Crystal form, accompanied by the note "crystalline form" nitrate nitrogen (NO3-N), water soluble magnesium (Mg) 5. Sodium nitrate is obtained chemically, as-15% sodium nitrate nitrate nitrogen (N) of nitrate nitrogen (NO3-N) 6. Chile nitre produced from the nuggets, as the Chilean nitrate, sodium nitrate, 15% nitrate nitrogen (N) of nitrate nitrogen (NO3-N) 7. Calcium cyanamide is obtained chemically, as-calcium cyanamide, calcium oxide, small amounts can contain ammonium salts and urea 18% total nitrogen (N). At least 75% of the declared in the form of cyanamide nitrogen is the total nitrogen (N) 8. Nitrogen in calcium cyanamide is obtained chemically, as-calcium cyanamide, calcium oxide, small amounts can contain ammonium salts and urea, supplemented by 18% nitrate nitrogen, total nitrogen (N). At least 75% of the declared in the form of cyanamide nitrogen is. Minimum content of nitrate nitrogen, 1% N. The maximum content of nitrate nitrogen – 3% N total nitrogen (N), nitrate nitrogen (NO3-N) 9. Ammonium sulphate obtained chemical, as – ammonium sulfate 20% ammoniacal nitrogen (N) ammonium nitrogen (N-NH4) 10. -Of calcium ammonium nitrate acquired chemical, as – ammonium nitrate, excipient-calcium carbonate (the limestone Malta) and (or) magnesium carbonate and calcium carbonate (the Malta dolomite) 20% of the total nitrogen (N). Nitric nitrogen and ammoniacal nitrogen each represent about half of the total nitrogen. The term "ammonium nitrate, calcium-" only for fertilizers, in addition to the ammonium nitrate containing only calcium carbonate (limestone) and (or) magnesium carbonate and calcium carbonate (dolomite). The carbonate content is 20% minimum. Carbonate purity not less than 90% of total nitrogen (N), nitrate nitrogen (NO3-N), ammoniacal nitrogen (N-NH4). In addition, you can declare: the total calcium (Ca), magnesium (Mg) overall, if fertilizer contains magnesium carbonate 11. Ammonium sulphate-nitrate derived chemical, as-ammonium nitrate and ammonium sulphate 25% total nitrogen (N). Nitrogen expressed as ammoniacal and nitrate nitrogen. Minimum nitric nitrogen content: 5% total nitrogen (N), nitrate nitrogen (NO3-N), ammoniacal nitrogen (N-NH4). In addition, you can declare: sulphur (S) 12. Ammonium-magnesium sulphate-nitrate derived chemical, basic components, ammonium nitrate, ammonium sulphate and magnesium sulphate for 19% of total nitrogen (N). Nitrogen is ammonia and nitrate form. Minimum nitric nitrogen content: 6%. 3.0% water soluble magnesium (Mg) total nitrogen (N), nitrate nitrogen (NO3-N), ammoniacal nitrogen (N-NH4), water soluble magnesium (Mg). In addition, you can declare: sulphur (S) 13. Magnesium-ammonium nitrate For the chemical, basic components – ammonium nitrate and magnesium compound salts (magnesium carbonate and/or magnesium sulphate) 19% total nitrogen (N). Nitrogen is ammonium (N-NH4) and nitrate (N-NO3) form. Minimum nitric nitrogen content: 6%. 3.0% total magnesium (Mg) total nitrogen (N), nitrate nitrogen (NO3-N), ammoniacal nitrogen (N-NH4), total magnesium (Mg) and soluble in water may magnesium (Mg) 14. Urea (urea), as its chemical-urea 44% total nitrogen (N). Nitrogen is the amide (N-NH2) form (including biuret). Maximum biuret Content: 1.2% (use the hard way). Maximum biuret Content: 0.5% (plant spraying), total nitrogen, expressed in nitrogen amide (N-NH2) form 15. Krotonilidendiurīnviel obtained chemically reacting with urea, CROTONIC aldehyde, monomer complex 28% total nitrogen (N). At least 25% N is krotonilidendiurīnviel. Maximum amide nitrogen content: 3% total nitrogen (N), the amide nitrogen (N-NH2), if it is 1% or more of the mass of the nitrogen composition of krotonilidendiurīnviel 16. Izobutilēndiurīnviel obtained chemically reacting with urea, izobutilēnaldehīd, monomer complex 28% total nitrogen (N). At least 25% N is izobutilēndiurīnviel. Maximum amide nitrogen content: 3% total nitrogen (N), the amide nitrogen (N-NH2), if it is 1% or more of the mass of the nitrogen composition of 17 izobutilēndiurīnviel. Urea formaldehyde, urea formaldehyde, reacting with urea-formaldehyde as molecules, a polymer complex 36% total nitrogen (N). At least 3/5 declared total nitrogen soluble in hot water. At least 31% of nitrogen is urea formaldehyde. The maximum nitrogen content of the amide-5% total nitrogen (N), the amide nitrogen (N-NH2), if it is 1% or more by weight, nitrogen urea formaldehyde, soluble in cold water. You can declare: urea formaldehyde, nitrogen, soluble only in hot water the 18. Nitrogen fertilizers, which contain a chemical krotonilidendiurīnviel, content krotonilidendiurīnviel and simple, except for nitrogen fertilizer calcium cyanamide, nitrogenous calcium cyanamide, ammonium-nitrate and calcium ammonium nitrate-18% total nitrogen (N). At least 3% nitrogen is ammonium nitrate and (or) and (or) the amide form. At least 1/3 of the total nitrogen is declared krotonilidendiurīnviel of nitrogen. Maximum biuret Content: (amide of N + krotonilidendiurīnviel N) × 0.026 total nitrogen, each of the form, the content of which is at least 1% of nitrate nitrogen (NO3-N), ammoniacal nitrogen (N-NH4), the amide nitrogen (N-NH2), nitrogen krotonilidendiurīnviel shall consist of 19. Nitrogen fertilizers, which contain a chemical izobutilēndiurīnviel, content izobutilēndiurīnviel and simple, except for nitrogen fertilizer calcium cyanamide, nitrogenous calcium cyanamide, ammonium-nitrate and calcium ammonium nitrate-18% total nitrogen (N). At least 3% nitrogen is ammonia, nitrate and (or) and (or) the amide form. At least 1/3 of the declared total nitrogen of nitrogen is izobutilēndiurīnviel. Maximum biuret Content: (amide-N + izobutilēndiurīnviel N) × 0.026 total nitrogen (N), each of the form, the content of which is at least 1% of nitrate nitrogen (NO3-N), ammoniacal nitrogen (N-NH4), the amide nitrogen (N-NH2), nitrogen composition of izobutilēndiurīnviel 20. Nitrogen fertilizers containing urea formaldehyde, the chemical content of urea formaldehyde and nitrogen fertilizers will facilitate other than calcium cyanamide, nitrogenous calcium cyanamide, ammonium-nitrate and calcium ammonium nitrate-18% total nitrogen (N). At least 3% nitrogen is ammonia, nitrate and (or) and (or) the amide form. At least 1/3 of the declared total nitrogen of urea formaldehyde, of which at least 3/5 is soluble in hot water. Maximum biuret Content: (amide-N + urea formaldehyde N) × 0.026 total nitrogen (N), each of the form, the content of which is at least 1% of nitrate nitrogen (NO3-N), ammoniacal nitrogen (N-NH4), the amide nitrogen (N-NH2), nitrogen urea formaldehyde, cold water soluble nitrogen urea formaldehyde. You can declare: only the hot water soluble nitrogen urea formaldehyde consists of 21. Ammonium sulphate with nitrification inhibitor (dicyandiamide) obtained chemical, ammonium sulphate content and 20% of dicyandiamide total nitrogen (N). Minimum of ammoniacal nitrogen content-18%. The minimum content of the nitrogen composition of dicyandiamide-1.5% of the total nitrogen (N), ammoniacal nitrogen (N-NH4), nitrogen, dicyandiamide, technical information about the use of time and dose 22. Ammonium sulphate nitrate by nitrification inhibitors (dicyandiamide) obtained chemical, ammonium sulfonitrāt and contents of dicyandiamide 24% total nitrogen (N). Minimum nitric nitrogen content: 3%. The minimum content of the nitrogen composition of dicyandiamide-1.5% of the total nitrogen (N), nitrate nitrogen (NO3-N), ammoniacal nitrogen (N-NH4), nitrogen, dicyandiamide, technical information about the use of time and dose of 23. Urea-ammonium sulphate obtained chemically from urea and ammonium sulfate 30% total nitrogen (N). Nitrogen is ammonium and amide form. The minimum content of ammoniacal nitrogen – 4%. Minimum sulphur content-4.8%. Maximum biuret Content: 0.9% total nitrogen (N), ammoniacal nitrogen (N-NH4), the amide nitrogen (N-NH2), water soluble sulfur (S) 24. 1. – paragraph 23 referred to in the nitrogen fertilizer with trace elements and (or) secondary feed items 1-23 of that nitrogen fertilizer with trace elements and (or) secondary feed elements method of production and essential data for 1-23 referred to in paragraph nitrogen fertilizers and added trace elements and (or) secondary feed items 1-23 of nitrogen fertilizers referred to the declared micro-nutrient content, according to the Cabinet on 1 September 2015 rule no. 506 "fertiliser and substrate identification quality, conformity assessment, and trade rules (hereinafter rules) "annex 4, secondary nutrient content according to the rules referred to in annex 12, 2. Phosphorus fertilizers (Granular fertilizers the grain size distribution is determined by the composition of an appropriate analytical method) No. p. k. The official name of the fertilizer production method, the basic quality requirements (plant nutrient minimum content (% by weight of the fertilizer), and applicable to the specific fertilizer) fertilizer, label or accompanying document must be declared on the labelling of quality indicators (%) and other requirements 1. Simple superphosphate is obtained by treating the soft ground rock phosphate or apatīt shredded with sulphuric acid, calcium dihydrogen phosphate-essential and calcium sulphate 16% neutral ammonium citrate soluble phosphorus (P2O5). At least 93% P2O5 quantity declared is a water-soluble form neutral ammonium citrate soluble phosphorus (P2O5) water soluble phosphorus (P2O5) 2. Concentrated superphosphate is obtained by treating the soft ground rock phosphate or shredded apatīt with sulfuric acid and phosphoric acid, calcium dihydrogen phosphate-essential and calcium sulphate 25% neutral ammonium citrate soluble phosphorus (P2O5). At least 93% P2O5 quantity declared is a water-soluble form neutral ammonium citrate soluble phosphorus (P2O5) water soluble phosphorus (P2O5) 3. Double superphosphate is obtained by treating the soft ground rock phosphate or apatīt shredded with phosphoric acid – calcium dihydrogen phosphate as 38% neutral ammonium citrate soluble phosphorus (P2O5). Not less than 93% of the declared quantity of phosphorus is a water-soluble form neutral ammonium citrate soluble phosphorus (P2O5) water soluble phosphorus (P2O5) 4. Superfos is obtained, chopped by treating soft ground rock phosphate with sulphuric acid or phosphoric acid, calcium dihydrogen phosphate-essential, calcium phosphate and calcium sulphate soluble in mineral acids 20% phosphorus (P2O5). At least 40% P2O5 quantity declared is water soluble. Particle size: at least 90% to pass through a sieve with a mesh size 0.160 mm; at least 98% passes through a sieve with a mesh size 0.630 mm total (soluble in mineral acids) phosphorus (P2O5) water soluble phosphorus (P2O5) 5. Precipitāt you get the drip of phosphoric acid of phosphorus-containing rock or bone, as-38% of calcium phosphate alkaline ammonium citrate soluble phosphorus (P2O5). Particle size: at least 90% to pass through a sieve with a mesh size 0.160 mm; at least 98% passes through a sieve with a mesh size 0.630 mm alkaline ammonium citrate soluble phosphorus (P2O5) 6. Calcium termofosfāt was obtained at elevated temperatures in Malta with processing the soft ground rock phosphate alkaline solutions and silīcijskāb, basic components – the alkaline calcium phosphate and calcium silicate 25% alkaline ammonium citrate soluble phosphorus (P2O5). Particle size: at least 75% passes through a sieve with a mesh size 0.160 mm; at least 96% passes through a sieve with a mesh size 0.630 mm alkaline ammonium citrate soluble phosphorus (P2O5) 7. Aluminium-calcium phosphate, torrefaction and grinding soft ground rock phosphate and (or) apatīt (amorphous form), as-aluminium and calcium phosphate soluble in mineral acids 30% phosphorus (P2O5). At least 75% P2O5 quantity declared is soluble in alkaline ammonium citrate ("Julie"). Particle size: at least 90% to pass through a sieve with a mesh size 0.160 mm; at least 98% passes through a sieve with a mesh size 0.630 mm total (soluble in mineral acids) phosphorus (P2O5), alkaline ammonium citrate soluble phosphorus (P2O5) 8. Soft obtained by grinding soft ground rock phosphate, the basic components-calcium phosphate and calcium carbonate soluble in mineral acids 25% phosphorus (P2O5). At least 55% P2O5 is declared in formic acid quantity divprocentīg soluble phosphorus (P2O5). Particle size: at least 90% to pass through a sieve with a mesh size of 0.063 mm; at least 99% to pass through a sieve with a mesh size 0.125 mm total (soluble in mineral acids) phosphorus (P2O5) soluble in formic acid divprocentīg phosphorus (P2O5). You can declare: material which passes through a sieve with a mesh of 0.063 mm is 9. Phosphorous slag (basic slag) obtained the iron smelting process, the basic components – calcium silicate-phosphate soluble in mineral acids 12% phosphorus (P2O5). At least 75% of the declared quantity of citric acid is divprocentīg P2O5 in the soluble phosphorus (P2O5) or 10% of the phosphorus soluble in citric acid divprocentīg (P2O5). Particle size: at least 75% passes through a sieve with a mesh size 0.160 mm; at least 96% passes through a sieve with a mesh size 0.630 mm total (soluble in mineral acids) phosphorus (P2O5) soluble in citric acid and divprocentīg in phosphorus (P2O5) soluble in citric acid or divprocentīg of phosphorus (P2O5) 10. 1.-9. phosphorus fertilizers referred to in paragraph with trace elements and (or) secondary feed elements 1 through 9, paragraph phosphatic fertilizer with trace elements and (or) secondary feed elements method of production and essential data for 1-9. phosphorus fertilizers referred to in paragraph 1 and added trace elements and (or) secondary feed elements 1 through 9, paragraph phosphatic fertilizer nutrient data, content of trace elements in accordance with annex 4 provisions, secondary nutrient content according to the rules of annex 12 3. Potassium fertilizers No. p. k. The official name of the fertilizer production method, the basic quality requirements (plant nutrient minimum content (% by weight of the fertilizer), and applicable to the specific fertilizer) fertilizer, label or accompanying document must be declared on the labelling of quality indicators (%) and other requirements 1. Kainite Obtained by milling the natural potassium salts basic components – potassium chloride and magnesium sulfate 10% water soluble potassium (K2O), 3.0% water soluble magnesium (Mg) water soluble potassium (K2O) water soluble magnesium (Mg) 2. Rich potassium salt Obtained by milling the natural potassium salts and enriching it with potassium chloride, mechanical mixing 18% water soluble potassium (K2O) water soluble potassium (K2O). May be an indication of water soluble magnesium (Mg) content, if it is higher than 3.0% 3. Potassium chloride is obtained by milling the natural potassium salts, potassium chloride – essential 37% water soluble potassium (K2O) water soluble potassium (K2O) 4. Magnesium-potassium chloride is obtained by milling the natural potassium salts and adding magnesium salts, basic components – potassium chloride and magnesium salts 37% water soluble potassium (K2O), 3.0% water soluble magnesium (Mg) water soluble potassium (K2O) water soluble magnesium (Mg) 5. Potassium sulphate obtained chemically from potassium salts, potassium sulphate as – 47% water soluble potassium (K2O), the maximum content of chlorine (Cl)-3% water soluble potassium (K2O). Indication of chlorine (Cl) content is not required if it is below 3% 6. Potassium magnesia obtained chemically from potassium salts by adding magnesium salts, basic components-potassium sulphate and magnesium sulphate 22% water soluble potassium (K2O), 4.8% water soluble magnesium (Mg). Maximum chlorine content (Cl)-3% water soluble potassium (K2O) water soluble magnesium (Mg). Indication of chlorine (Cl) content is not required if it is below 3% 7. Kizerīt with potassium sulphate Obtained by milling the kizerīt and adding potassium sulphate 4.8% water soluble magnesium (Mg), 6% water soluble potassium (K2O), 16% (Mg + K2O). Maximum chlorine content (Cl)-3% water soluble magnesium (Mg), water soluble potassium (K2O). Indication of chlorine (Cl) content is not required if it is below 3% 8. 1 through 7 above, potassium fertilizers with trace elements and (or) secondary feed items 1 through 7 above potassium fertilizer with trace elements and (or) secondary feed elements method of production and essential data for 1-7 potassium fertilizers listed in and added trace elements and (or) secondary feed items 1-7 of potassium fertilizers referred to the declared data, content of trace elements in accordance with the provisions of annex 4, secondary nutrient content according to the rules of annex b. 12 Complex fertilizers NPK fertilizers No 1. p. k. The official name of the fertilizer production method, the basic quality requirements (plant nutrient minimum content (% by weight of the fertilizer), and applicable to the specific fertilizer) fertilizer, label or accompanying document must be declared on the labelling of quality indicators (%) and other requirements 1. NPK fertilizers obtained chemically or by blending NPK-mechanical components. Contains no animal or vegetable organic compounds 20% (N + P2O5 + K2O), it skaitā3% nitrogen (N), its forms: 1) total nitrogen; 2) nitrate nitrogen; 3) ammonium nitrogen; 4) amide nitrogen; cyanamide nitrogen 5). 5% phosphorus (P2O5), its forms: 1) water soluble P2O5; 2) neutral ammonium citrate soluble P2O5; 3) total (soluble in mineral acids), P2O5; 4 divprocentīg in soluble in citric acid), P2O5 (only those fertilizers containing phosphorus-containing slag); 5) alkaline ammonium citrate soluble P2O5 (only those fertilizers containing aluminium-calcium phosphate, calcined phosphate); 6) formic acid soluble P2O5 in divprocentīg (only for fertilizers, which contain soft). NPK fertilizers 1) that do not have a phosphorus-containing slag, calcined phosphate, aluminium-calcium phosphate, soft ground, superfos and soluble in mineral acids only P2O5 does not exceed 2%. NPK fertilizers: (a) 2)) which is soft or superfos, must not be phosphorous slag, calcined phosphate and aluminium-calcium phosphate. These fertilizers contain: at least 2% P2O5 soluble in mineral acids only, at least 5% in water and neutral ammonium citrate soluble P2O5 at least 2.5% P2O5 soluble in water; (b)) containing aluminium-calcium phosphate must be phosphorous slag, calcined phosphate and superfos. These fertilizers contain: at least 2% water-soluble P2O5 (form 1), at least 5% P2O5 soluble in mineral acids, of which at least 75% P2O5 soluble declared alkaline ammonium citrate. NPK fertilizers contain 3) if only one form of phosphorus fertilizer, phosphorus-containing slag, calcined phosphate, aluminium-calcium phosphate, soft ground, or their name indicates, these essential components: fertilizers, which contain aluminium calcium phosphate, at least 75% of the declared content of P2O5 soluble in alkaline ammonium citrate, fertilizer, which is soft, at least 55% of the declared content of P2O5 soluble in citric acid divprocentīg. Granulometry: phosphorous slag: at least 75% of the particles pass through a sieve with a mesh size 0.160 mm, aluminium-calcium phosphate: at least 90% of the particles pass through a sieve with a mesh size 0.160 mm, calcined phosphate: at least 75% of the particles pass through a sieve with a mesh size 0.160 mm soft for at least 90% of the particles pass through a sieve with a mesh of 0.063 mm, superfos is at least 90% of the particles pass through a sieve which size of 0.160 mm. 5% water soluble K2O total nitrogen: nitrogen (N). If one of 2-5. the nitrogen forms in at least 1% of the mass, it declares. Phosphorus: 1) NPK fertilizers that contain no phosphorus-containing slag, calcined phosphate, aluminium-calcium phosphate, soft ground, superfos and declare 1 and (or) the solubility of phosphorus form 2: If the water-soluble P2O5 is less than 2%, declared only 2. solubility of phosphorus form; If the water-soluble P2O5 is at least 2%, declared 1 and 2, the solubility of phosphorus form. NPK fertilizers: (a) 2)) which is soft or superfos, declares 1, 2, and 3. the solubility of phosphorus form. Fertilizers contain the indication "of NPK fertilizer containing soft ground ' or ' NPK fertilizer containing Superfos '; (b)) containing aluminium-calcium phosphate, declares 1, 3 and 5. the solubility of phosphorus form. Fertilizers contain the indication "aluminium-calcium phosphate-containing fertilizers NPK". NPK fertilizers contain 3) only one form of phosphorus fertilizer, phosphorus-containing slag, calcined phosphate, aluminium-calcium phosphate or soft. Fertiliser name must name this essential components; P2O5 solubility declares: fertilizers containing phosphorus-containing slag,-4. solubility of phosphorus form of fertilizers containing calcined phosphate: solubility of phosphorus form 5, fertilizers, containing aluminium-calcium phosphate – 3 and 5 the solubility of phosphorus in the form of fertilizers, which contain soft, 6-3, and the solubility of phosphorus form. Potassium: water soluble potassium (K2O). ' Low in chlorine ' may be added, if the chlorine (Cl) content not exceeding 2%. The chlorine content may be declared 2. NPK fertilizers containing krotonilidendiurīnviel, izobutilēndiurīnviel, or urea formaldehyde, chemical content of animal or plant origin, contains organic compounds or urea formaldehyde krotonilidenizobutilēndiurīnviel 20% (N + P2O5 + K2O) 5% nitrogen (N), its forms: 1) total nitrogen; 2) nitrate nitrogen; 3) ammonium nitrogen; 4) amide nitrogen; 5 krotonilidendiurīnviel of nitrogen); 6 izobutilēndiurīnviel of nitrogen); 7) urea formaldehyde nitrogen. At least 1/4 of the total nitrogen consists of 5, 6 or 7. nitrogen form. At least 3/5 of the 7. nitrogen form of soluble in hot water. 5% phosphorus (P2O5), its forms: 1) water soluble P2O5; 2) neutral ammonium citrate soluble P2O5. NPK fertilizers that contain no phosphorus-containing slag, calcined phosphate, aluminium-calcium phosphate, soft ground, superfos and soluble in mineral acids only P2O5 may not exceed 2%. 5% water soluble potassium (K2O), nitrogen: total nitrogen (N). 2.-4. nitrogen form, if any of them is at least 1% of the mass. One of 5-7. nitrogen forms phosphorus: NPK fertilizers that contain no phosphorus-containing slag, calcined phosphate, aluminium-calcium phosphate, soft ground, superfos and declares P2O5 1. and 2. the solubility of phosphorus form: If the water-soluble P2O5 is less than 2%, declared only 2. solubility of phosphorus form if the water-soluble P2O5 is at least 2%, declared 1 and 2, the solubility of phosphorus form. Potassium: water soluble potassium (K2O). Indication ' Low in chlorine ' may be added, if the chlorine (Cl) content not exceeding 2%. The chlorine content may be declared 3. 1.-2. NPK fertilizers referred to in paragraph with trace elements and (or) secondary feed items 1-2 of NPK fertilizers referred to in paragraph with trace elements and (or) secondary feed elements method of production and essential data for 1-2 referred to in paragraph NPK fertilizers and added trace elements and (or) secondary elements of feedingstuffs 1.-2. NPK fertilizers referred to the declared data, content of trace elements in accordance with the provisions of annex 4, secondary nutrient content according to annex 2 of the regulations 12. NP fertilisers No. p. k. The official name of the fertilizer production method, the basic quality requirements (plant nutrient minimum content (% by weight of the fertilizer), and applicable to the specific fertilizer) fertilizer, label or accompanying document must be declared on the labelling of quality indicators (%) and other requirements 1. NP fertilizers obtained chemically or mechanically mixing the NP containing components, contains no animal or vegetable organic compounds 18% (N + P2O5) 3% nitrogen (N), it shapes: 1) total nitrogen; 2) nitrate nitrogen; 3) ammonium nitrogen; 4) amide nitrogen; cyanamide nitrogen 5). 5% phosphorus (P2O5), its forms: 1) water soluble P2O5; 2) neutral ammonium citrate soluble P2O5; 3) total (soluble in mineral acids), P2O5; 4 divprocentīg in soluble in citric acid), P2O5 (only those fertilizers containing phosphorus-containing slag); 5) alkaline ammonium citrate soluble P2O5 (only those fertilizers containing aluminium-calcium phosphate, calcined phosphate); 6) formic acid soluble P2O5 in divprocentīg (only for fertilizers, which contain soft). 1) NP fertilizer containing no phosphorus-containing slag, calcined phosphate, aluminium-calcium phosphate, soft ground, superfos and soluble in mineral acids only P2O5 does not exceed 2%; 2) NP fertilizer: a) are soft or superfos, must not be phosphorous slag, calcined phosphate and aluminium-calcium phosphate. These fertilizers contain: at least 2% P2O5 soluble in mineral acids only, at least 5% in water and neutral ammonium citrate soluble P2O5 at least 2.5% water-soluble P2O5, b) containing aluminium-calcium phosphate must be phosphorous slag, calcined phosphate, soft ground and superfos. These fertilizers contain: at least 2% water-soluble P2O5, at least 75% P2O5 soluble declared alkaline ammonium citrate; NP fertilizers contain 3) if only one form of phosphorus fertilizer, phosphorus-containing slag, calcined phosphate, aluminium-calcium phosphate, soft ground, or their name indicates, these essential components: fertilizers, which contain aluminium calcium phosphate, at least 75% of the declared content of P2O5 soluble in alkaline ammonium citrate, fertilizer, which is soft, at least 55% of the declared content of P2O5 soluble in citric acid divprocentīg. Granulometry: phosphorous slag – at least 75% of the particles pass through a sieve with a mesh size 0.160 mm; aluminium-calcium phosphate: at least 75% of the particles pass through a sieve with a mesh size 0.160 mm; calcined phosphate: at least 75% of the particles pass through a sieve with a mesh size 0.160 mm; soft, at least 90% of the particles pass through a sieve with a mesh size of 0.063 mm; superfos – at least 90% of the particles pass through a sieve with a mesh size 0.160 mm nitrogen: total nitrogen (N). If one of 2-5. the nitrogen forms is not less than 1% of the mass, it declares. Phosphorus: 1) NP fertilizer containing no phosphorus-containing slag, calcined phosphate, aluminium-calcium phosphate, soft ground, superfos and declare 1 and 2.  the solubility of phosphorus form: If the water-soluble P2O5 is less than 2%, declared only 2. solubility of phosphorus form; If the water-soluble P2O5 is at least 2%, declared 1 and 2, the solubility of phosphorus form. 2) NP fertilizers: a) are soft or superfos, declares 1, 2 and 3. the solubility of phosphorus form. Fertilizers contain the indication "NP fertilizer containing soft ground" or "NP fertilizer containing Superfos '; (b)) containing aluminium-calcium phosphate, declares 1, 3 and 5. the solubility of the form. The fertilizer trade name must be "NP fertilizer containing aluminium-calcium phosphate '. 3) NP fertilizers contain only one form of phosphorus fertilizer, phosphorus-containing slag, calcined phosphate, aluminium-calcium phosphate or soft. Fertiliser name must name these essential ingredients. P2O5 solubility declares: fertilizers containing phosphorus-containing slag,-4. solubility of phosphorus form of fertilizers containing calcined phosphate: solubility of phosphorus form 5, fertilizers, containing aluminium-calcium phosphate – 3 and 5 the solubility of phosphorus in the form of fertilizers, which contain soft, 6-3 and solubility of phosphorus form 2. NP fertilizers containing krotonilidendiurīnviel, izobutilēndiurīnviel, or urea formaldehyde chemical. They contain no animal or vegetable organic compounds. It contains krotonilidendiurīnviel, izobutilēndiurīnviel, or urea formaldehyde 18% (N + P2O5) 5% nitrogen (N), its forms: 1) total nitrogen; 2) nitrate nitrogen; 3) ammonium nitrogen; 4) amide nitrogen; 5 krotonilidendiurīnviel of nitrogen); 6 izobutilēndiurīnviel of nitrogen); 7) urea formaldehyde nitrogen. At least 1/4 of the declared total amount of nitrogen is 5, 6, or 7. nitrogen form. At least 3/5 of the declared 7. quantity of nitrogen form soluble in hot water. 5% phosphorus (P2O5), its forms: 1) water soluble P2O5; 2) neutral ammonium citrate soluble P2O5. NP fertilizer containing no phosphorus-containing slag, calcined phosphate, aluminium-calcium phosphate and superfos, P2O5 soluble in mineral acids only must not exceed 2% of the total nitrogen: nitrogen (N) 2, 3, or 4. nitrogen form, if they are more than 1% of the mass. One of 5-7. nitrogen forms. Phosphorus: NP fertilizers containing no phosphorus-containing slag, calcined phosphate, aluminium-calcium phosphate, superfos, declares the solubility of 1 or 2 shape: If the water-soluble P2O5 is less than 2%, declared only 2. solubility of phosphorus form; If the water-soluble P2O5 is at least 2%, declared 1 and 2 solubility of phosphorus form 3. 1.-2. NP fertilizers referred to in paragraph with trace elements and (or) secondary feed elements 1-2 NP fertilizers referred to in paragraph with trace elements and (or) secondary feed elements method of production and essential data for 1-2 NP fertilizers referred to in paragraph and added trace elements and (or) secondary feed elements 1-2. NP fertilizers referred to the declared data, content of trace elements in accordance with the provisions of annex 4, secondary nutrient content according to the rules of annex 12. NK fertilisers No 3. p. k. The official name of the fertilizer production method, the basic quality requirements (plant nutrient minimum content (% by weight of the fertilizer), and applicable to the specific fertilizer) fertilizer, label or accompanying document must be declared on the labelling of quality indicators (%) and other requirements 1. NK fertilizers obtained chemically or mechanically mixing SNA-components, contains no animal or vegetable organic compounds 18% (N + K2O) 3% nitrogen (N), it shapes: 1) total nitrogen; 2) nitrate nitrogen; 3) ammonium nitrogen; 4) amide nitrogen; cyanamide nitrogen 5). 5% water soluble K2O total nitrogen: nitrogen (N) 2-5. nitrogen form, if any of them is at least 1% of the mass. Potassium: water soluble potassium (K2O). ' Low in chlorine ' adds, if chlorine (Cl) content not exceeding 2%. The chlorine content may be declared 2. NK fertilizers containing krotonilidendiurīnviel, izobutilēndiurīnviel, or urea formaldehyde by mixing chemical components, containing SNA contains no animal or vegetable organic compounds, containing krotonilidendiurīnviel, izobutilēndiurīnviel, or urea formaldehyde 18% (N + K2O) 5% nitrogen (N), it shapes: 1) total nitrogen; 2) nitrate nitrogen; 3) ammonium nitrogen; 4) amide nitrogen; 5 krotonilidendiurīnviel of nitrogen); 6 izobutilēndiurīnviel of nitrogen); 7) urea formaldehyde nitrogen. At least 1/4 the total amount of nitrogen is 5, 6, or 7. form nitrogen. At least 3/5 declared 7. nitrogen form is soluble in hot water. 5% water soluble K2O total nitrogen: nitrogen (N) 2.-4. nitrogen form, if any of them is at least 1% of the mass. One of 5-7. nitrogen forms. Potassium: water soluble potassium (K2O). ' Low in chlorine ' adds, if chlorine (Cl) content not exceeding 2%. The chlorine content may be declared 3. 1.-2. NK fertilisers referred with trace elements and (or) secondary feed elements 1-2 paragraph NK fertilizer with trace elements and (or) secondary feed elements method of production and essential data for 1-2 NK fertilizers referred to in paragraph and added trace elements and (or) secondary feed elements 1-2. NK fertilisers referred to the declared data, content of trace elements in accordance with the provisions of annex 4, secondary nutrient content according to the rules of annex 4 12 PK fertilizers No. p. k. The official name of the fertilizer production method, the basic quality requirements (plant nutrient minimum content (% by weight of the fertilizer), and applicable to the specific fertilizer) fertilizer, label or accompanying document must be declared on the labelling of quality indicators (%) and other requirements 1. PK fertilizers obtained chemically or by blending components, not containing ACC content of animal or plant origin organic compounds 18% (P2O5 + K2O) 5% phosphorus (P2O5), its forms: 1) water soluble P2O5; 2) neutral ammonium citrate soluble P2O5; 3) total (soluble in mineral acids), P2O5; 4 divprocentīg in soluble in citric acid), P2O5 (only those fertilizers containing phosphorus-containing slag); 5) alkaline ammonium citrate soluble P2O5 (only those fertilizers containing aluminium-calcium phosphate and calcined phosphate); 6) formic acid soluble P2O5 in divprocentīg (only for fertilizers, which contain soft). 1) PK fertilizer containing no phosphorus-containing slag, calcined phosphate, aluminium-calcium phosphate, soft ground, superfos and soluble in mineral acids only P2O5 does not exceed 2%. 2) PK fertilizer: a) are soft or superfos, must not be phosphorous slag, calcined phosphate and aluminium-calcium phosphate. These fertilizers contain: at least 2% P2O5 soluble in mineral acids only, at least 5% in water and neutral ammonium citrate soluble P2O5 at least 2.5% water-soluble P2O5, b) containing aluminium-calcium phosphate must be phosphorous slag, calcined phosphate, soft ground and superfos. These fertilizers contain: at least 2% water-soluble P2O5, at least 75% of the declared P2O5 soluble in alkaline ammonium citrate. 3) If PK fertilizers contain only one form of phosphorus fertilizer, phosphorus-containing slag, calcined phosphate, aluminium-calcium phosphate, soft ground, or their name indicates, these essential components: fertilizers, which contain aluminium calcium phosphate, at least 75% of the declared content of P2O5 soluble in alkaline ammonium citrate, fertilizer, which is soft, at least 55% of the declared content of P2O5 soluble in citric acid divprocentīg. Granulometry: phosphorous slag – at least 75% of the particles pass through a sieve with a mesh size 0.160 mm; aluminium-calcium phosphate: at least 90% of the particles pass through a sieve with a mesh size 0.160 mm; calcined phosphate: at least 75% of the particles pass through a sieve with a mesh size 0.160 mm; soft, at least 90% of the particles pass through a sieve with a mesh size of 0.063 mm; superfos – at least 90% of the particles pass through a sieve with a mesh size 0.160 mm. 5% water soluble K2O phosphorus: 1) PK fertilizer containing no phosphorus-containing slag, calcined phosphate, aluminium-calcium phosphate, soft ground, superfos and declared in accordance with 1 and 2 solubility of phosphorus form: If the water soluble phosphorus (P2O5) is less than 2%, declared only 2. solubility of phosphorus form; * If water soluble phosphorus (P2O5) is declaring at least 2%, 1 and 2, the solubility of phosphorus form. 2) PK fertilizer: a) are soft or superfos, declares 1, 2, and 3. the solubility of phosphorus form. Fertilizers contain the indication "PK fertilizers contain soft" or "PK fertilizers contain superfos '; (b)) FRI, which fertilizer is aluminium-calcium phosphate, declares 1, 3, and 5. the solubility of phosphorus form. Trade name references the fertilizers ' PK fertilizer containing aluminium-calcium phosphate '. NPK fertilizers contain 3) only one form of phosphorus fertilizer, phosphorus-containing slag, calcined phosphate, aluminium-calcium phosphate or soft. Fertiliser name must name these essential ingredients. P2O5 solubility declares: fertilizers containing phosphorus-containing slag,-4. solubility of phosphorus form of fertilizers containing calcined phosphate: solubility of phosphorus form 5, fertilizers, containing aluminium-calcium phosphate – 3 and 5 the solubility of phosphorus in the form of fertilizers, which contain soft, 6-3, and the solubility of phosphorus form. Water soluble potassium potassium (K2O). ' Low in chlorine ' may be added, if the chlorine (Cl) content not exceeding 2%. Chlorine (Cl) content can be declared 2. PK fertilizer with trace elements and (or) secondary nutrient elements fertiliser with trace elements, PK and (or) secondary feed elements method of production and essential data for PK fertilizers and added trace elements and (or) secondary nutrient elements fertiliser output data FRI, content of trace elements in accordance with the provisions of annex 4, secondary nutrient content under the terms of annex c. 12 liquid fertilizers liquid fertilizers 1. just no. p. k. The official name of the fertilizer production method, the basic quality requirements (plant nutrient minimum content (% by weight of the fertilizer), and applicable to the specific fertilizer) fertilizer, label or accompanying document must be declared on the labelling of quality indicators (%) and other requirements 1. Nitrogen fertilizer solution obtained by chemical and (or) water dissolve various components that are stable in the atmosphere. Contains no animal or vegetable organic compounds 15% total nitrogen (N), expressed in the form of total nitrogen. If there is only one form of nitrogen, nitrate nitrogen expressed as ammoniacal nitrogen or amide nitrogen form. Maximum biuret Content: N × 0.026 total amide nitrogen (N) and nitrate (N-NO3), ammonium (N-NH4) and (or) amide (N-NH2) nitrogen, if any of its form is not less than 1%. If the biuret Content is less than 0.2% may indicate "low biuret Content" 2. Ammonium nitrate-urea solution is obtained by chemical and (or) water dissolving ammonium nitrate and urea 26% of total nitrogen (N). About half of the total nitrogen is the amide nitrogen. Maximum biuret Content: 0.5% total nitrogen (N), nitrate, ammonium and amide nitrogen. If the biuret Content is less than 0.2% may indicate "low biuret Content" 3. Calcium nitrate Calcium nitrate water solution 8% total nitrogen (N). Nitrogen in the form of nitrate and ammonium. The maximum content of ammoniacal nitrogen, 1% total nitrogen (N). Desirable: nitrate nitrogen (NO3-N), ammoniacal nitrogen (N-NH4), calcium (Ca). The indication for use: "plant", "feed of spraying solution preparation", "Papildmēslošan" with the irrigation 4. Magnesium nitrate chemical extracted magnesium nitrate water solution 6% nitrate nitrogen (N), 5 4% water soluble magnesium (Mg). Minimum pH 4.0-nitrate nitrogen (NO3-N), water soluble magnesium (Mg) 5. Calcium nitrate Calcium nitrate suspension suspension in water 8% total nitrogen (N). Nitrogen in the form of nitrate and ammonium. The maximum content of ammoniacal nitrogen – 1%. 10% water soluble calcium (Ca), total nitrogen (N), nitrate nitrogen (NO3-N), water soluble calcium (Ca). The indication for use: "plant spraying solution", "feed", "preparation of Papildmēslošan with the watering" 6. Nitrogen fertiliser solution with urea formaldehyde obtained chemically or urea formaldehyde and other nitrogen fertilizers (other than calcium cyanamide, nitrogenous calcium cyanamide, ammonium-nitrate and calcium ammonium nitrate) 18% water solution total nitrogen (N). At least 1/3 of the total declared the nitrogen content of urea formaldehyde is composed. Maximum biuret Content: (amide-N + urea formaldehyde N) × 0.026 total nitrogen (N). Each form of nitrogen, if at least 1% of nitrate nitrogen (NO3-N), ammoniacal nitrogen (N-NH4), the amide nitrogen (N-NH2), nitrogen urea formaldehyde composition 7. Nitrogen fertiliser suspension with urea formaldehyde is chemically Obtained or urea formaldehyde and other nitrogen fertilizers (other than calcium cyanamide, nitrogenous calcium cyanamide, ammonium-nitrate and calcium ammonium nitrate) suspension in water 18% total nitrogen (N). At least 1/3 of the declared total nitrogen content of urea formaldehyde, of which at least 3/5 is soluble in hot water. Maximum biuret Content: (amide-N + urea formaldehyde N) × 0.026 total nitrogen (N). Each form of nitrogen, if at least 1% of nitrate nitrogen (NO3-N), ammoniacal nitrogen (N-NH4), the amide nitrogen (N-NH2), nitrogen urea formaldehyde, nitrogen urea formaldehyde such composition, which dissolve in cold water. You can declare: nitrogen urea-formaldehyde, which is soluble in hot water, only 8. Ammonia is obtained by dissolving in water gaseous ammonia. Can also contain other nitrogen-containing salts 15% total nitrogen (N). Nitrogen in the form of total ammonia nitrogen (N), ammoniacal nitrogen (N-NH4). Each form of nitrogen, if at least 1% 9. Anhydrous ammonia is obtained by chemical high pressure in the presence of a catalyst from molecular nitrogen and hydrogen 80% total nitrogen (N). Nitrogen: total nitrogen, 10. 1.-9. simple referred to liquid fertilizer with trace elements and (or) secondary feed elements 1-9. simple referred to a liquid fertilizer with trace elements and (or) secondary feed elements method of production and essential data for 1-9. simple referred to the liquid fertilizers and added trace elements and (or) secondary feed elements 1 through 9 simple paragraph liquid fertilizer nutrient data, content of trace elements in accordance with annex 4 of the rules. , secondary nutrient content according to annex 2 of the regulations 12. Complex liquid fertilizers No.  p. k. The official name of the fertilizer production method, the basic quality requirements (plant nutrient minimum content (% by weight of the fertilizer), and applicable to the specific fertilizer) fertilizer, label or accompanying document must be declared on the labelling of quality indicators (%) and other requirements 1. NPK fertilizer solution obtained by chemical and (or) dissolved in water that contains NPK components. Stable at normal atmospheric pressure, contains no animal or vegetable organic compounds 15% (N + P2O5 + K2O). 2% nitrogen (N), its forms: 1) total nitrogen; 2) nitrate nitrogen; 3) ammonium nitrogen; 4) amide nitrogen. 3% water-soluble phosphorus (P2O5) 3% water-soluble potassium (K2O). Maximum biuret Content: amide nitrogen: N × 0.026 total nitrogen (N). If 2.-4. nitrogen form is more than 1% of the mass, it declares. If the biuret Content is less than 0.2%, the words ' low in biuret Content ". Phosphorus: water soluble phosphorus (P2O5). Potassium: water soluble potassium (K2O). The indication "low chlorine content" If the chlorine (Cl) content not exceeding 2%. The chlorine content may be declared 2. NPK fertilizer suspension liquid fertilizers that contain plant nutrients are dissolved in water and both in suspension and which contains no animal or vegetable organic compounds 20% (N + P2O5 + K2O). 3% nitrogen (N), it shapes: 1) total nitrogen; 2) nitrate nitrogen; 3) ammonium nitrogen; 4) amide nitrogen; Maximum biuret Content: N × 0.026 amides. 4% phosphorus (P2O5), its forms: 1) water soluble P2O5; 2) neutral ammonium citrate soluble P2O5. The fertilizers must not contain phosphorous slag, aluminium-calcium phosphate, soft ground rock phosphate or natural superfos and (or) apatīt. 4% water soluble potassium (K2O), nitrogen: total nitrogen (N). If 2, 3 or 4. nitrogen form is more than 1% of the mass, it declares. If the biuret Content is less than 0.2%, the words ' low in biuret Content ". Phosphorus: If the water-soluble P2O5 is less than 2%, declared only 2. solubility of phosphorus form. If the water-soluble P2O5 is at least 2%, declared 1 and 2, the solubility of phosphorus form. Potassium: ' low in chlorine ' adds, if chlorine (Cl) content not exceeding 2%. The chlorine content may be declared 3. NP fertilizer solution Obtained chemically and by dissolution in water (or) NP-containing components. Stable atmosphere, contains no animal or vegetable organic compounds 18% (N + P2O5) 3% nitrogen (N), it shapes: 1) total nitrogen; 2) nitrate nitrogen; 3) ammonium nitrogen; 4) amide nitrogen. Maximum biuret Content: N × 0.026 amides. 5% water soluble phosphorus (P2O5) total nitrogen: nitrogen (N). If 2, 3 or 4. nitrogen form is at least 1% of the mass, it declares. If the biuret Content is less than 0.2%, the words ' low in biuret Content ". Phosphorus: water soluble phosphorus (P2O5) 4. NP fertilizer suspension liquid fertilizers that contain plant nutrients are dissolved in water and both in suspension and which contains no animal or vegetable organic compounds 18% (N + P2O5) 3% nitrogen (N), it shapes: 1) total nitrogen; 2) nitrate nitrogen; 3) ammonium nitrogen; 4) amide nitrogen. Maximum biuret Content: N × 0.026 amides. 5% phosphorus (P2O5), its forms: 1) water soluble P2O5; 2) neutral ammonium citrate soluble P2O5. The fertilizer must not have phosphorous slag, aluminium calcium phosphate, calcined phosphate, soft ground rock phosphate and natural superfos and (or) nitrogen apatīt: total nitrogen (N). If 2, 3 or 4. nitrogen form is at least 1% of the mass, it declares. If the biuret Content is less than 0.2%, the words ' low in biuret Content ". Phosphorus: If the water-soluble P2O5 is less than 2%, declared only 2. solubility of phosphorus form. If the water-soluble P2O5 is at least 2%, declared 1 and 2 solubility of phosphorus form 5. NK fertilizer solution Obtained chemically and by dissolution in water. Stable atmosphere, contains no animal or vegetable organic compounds 15% (N + K2O) 3% nitrogen (N), it shapes: 1) total nitrogen; 2) nitrate nitrogen; 3) ammonium nitrogen; 4) amide nitrogen. Maximum biuret Content: N × 0.026 amides. 5% water soluble potassium (K2O), nitrogen: total nitrogen (N). If 2, 3 or 4. nitrogen form is at least 1% of the mass, it declares. If the biuret Content is less than 0.2%, the words ' low in biuret Content ". Potassium: water soluble potassium (K2O). ' Low in chlorine ' adds, if chlorine (Cl) content not exceeding 2%. The chlorine content may be declared 6. NK fertilizer suspension liquid fertilizers that contain plant nutrients are dissolved form, dissolved in water or in suspension and which contains no animal or vegetable organic compounds 18% (N + K2O) 3% nitrogen (N), it shapes: 1) total nitrogen; 2) nitrate nitrogen; 3) ammonium nitrogen; 4) amide nitrogen. Maximum biuret Content: N × 0.026 amides. 5% water soluble potassium (K2O), nitrogen: total nitrogen (N). If 2, 3 or 4. nitrogen form is at least 1% of the mass, it declares. If the biuret Content is less than 0.2%, the words ' low in biuret Content ". Potassium: water soluble potassium (K2O). ' Low in chlorine ' adds, if chlorine (Cl) content not exceeding 2%. The chlorine content may be declared a 7. PK fertilizer solution Obtained chemically and by dissolution in water. Contains no animal or vegetable organic compounds 18% (P2O5 + K2O) 5% water soluble phosphorus (P2O5) water soluble 5% potassium (K2O) water soluble Phosphorus: phosphorus (P2O5). Potassium: water soluble potassium (K2O). ' Low in chlorine ' adds, if chlorine (Cl) content not exceeding 2%. The chlorine content may be declared 8. PK fertilizer suspension liquid fertilizers that contain plant nutrients are dissolved in water and both in suspension and which contains no animal or vegetable organic compounds 18% (P2O5 + K2O). 5% phosphorus (P2O5), its forms: 1) water soluble P2O5; 2) neutral ammonium citrate soluble P2O5. The fertilizer must not have phosphorous slag, aluminium calcium phosphate, calcined phosphate, soft ground rock phosphate and natural superfos and (or) apatīt. 5% water soluble Phosphorus potassium (K2O) water soluble: If the P2O5 is less than 2%, declared only 2. solubility of phosphorus form. If the water-soluble P2O5 is at least 2%, declared 1 and 2, the solubility of phosphorus form. Potassium: water soluble potassium (K2O). ' Low in chlorine ' adds, if chlorine (Cl) content not exceeding 2%. The chlorine content may be declared 9. 1.-the complex referred to in paragraph 8 in liquid fertilizer with trace elements and (or) secondary feed elements 1 through 8 of paragraph complex liquid fertilizer with trace elements and (or) secondary feed elements method of production and essential data for 1-8 package listed in the liquid fertilizers and added trace elements and (or) secondary feed elements 1 through 8 of paragraph complex liquid fertilizer nutrient data, content of trace elements in accordance with the provisions of annex 4, secondary nutrient content according to Annex D of the rules 12. Secondary plant nutrients (calcium, magnesium and sulphur) fertilisers containing No. p. k. The official name of the fertilizer production method, the basic quality requirements (plant nutrient minimum content (% by weight of the fertilizer), and applicable to the specific fertilizer) fertilizer, label or accompanying document must be declared on the labelling of quality indicators (%) and other requirements 1. Calcium sulphate obtained, the calcium sulphate-free grinding rocks, with different degree of hydration or industrial product 17.9% total calcium (Ca), 14% of the total sulphur (S). Granulometry: at least 80% of the particles pass through a sieve with a 2 mm mesh size, at least 99% of the particles pass through a sieve with a mesh size is 10 mm total sulphur (S), preferably the total calcium (Ca) 2. Calcium chloride solution of industrial origin calcium chloride solution 8.6% of the total calcium (Ca), total calcium (Ca), the desired "plant sprinkling" 3. Elemental sulphur natural origin or acquired 98% of the total sulphur sulphur (S) total sulphur (S) 4. Kizerīt natural mineral obtained. As-magnesium sulphate monohydrate 14.5% water soluble magnesium (Mg) 18% water-soluble sulfur (S) water soluble magnesium (Mg), preferably water soluble sulfur (S) 5. Magnesium sulphate fertilizer, which as-magnesium sulphate heptahydrate 9.0% water soluble magnesium (Mg), 11 2% water-soluble sulfur (S) water soluble magnesium (Mg), preferably water soluble sulfur (S) 5.1. Magnesium sulphate solution obtained in Industrial magnesium sulphate solution water soluble in water 3.0% magnesium (Mg), 4% water-soluble sulfur (S) water soluble magnesium (Mg), preferably water soluble sulfur (S) 5.2. The magnesium hydroxide produced chemically. As-magnesium hydroxide 36.2% total magnesium (Mg). Particle size: at least 99% of the particles pass through a sieve with a mesh size of 0.063 mm total magnesium (Mg) 5.3. Magnesium hydroxide magnesium hydroxide suspension suspension water 14.5% magnesium (Mg) magnesium (Mg) total 6. Magnesium chloride solution of industrial magnesium chloride obtained water solution 7.8% magnesium (Mg). Maximum calcium content – 2.1% Ca total magnesium (Mg) 7. Kizerīt with potassium sulphate obtained from kizerīt by adding potassium sulphate 4.8% water soluble magnesium (Mg), 6% water soluble potassium (K2O), 16% (Mg + K2O). Maximum chlorine content (Cl)-3% water soluble magnesium (Mg) water soluble potassium (K2O) 8. 1 through 7 above secondary fertilizers with trace elements 1 through 7 above secondary fertilizer with trace elements method of production and essential data for 1-7 referred to in paragraph secondary fertilizers and added trace elements 1 through 7 above secondary nutrient fertilizers data content of trace elements in accordance with the provisions of annex e. 4 Only fertilizers containing micronutrients (mikromēsl) No. p. k. The official name of the fertilizer production method, the basic quality requirements (plant nutrient minimum content (% by weight of the fertilizer), and applicable to the specific fertilizer) fertilizer, label or accompanying document must be declared on the labelling of quality indicators (%) and other requirements 1.1a boric acid boron is obtained by acting on acid Borate 14% water soluble boron (B) water soluble boron (B) (1). (b) Sodium Borate For chemically , as-Sodium Borate 10% water soluble boron (B) water soluble boron (B) 1 c Calcium Borate from boron-containing fertilizers, as calcium Borate – 7% of the total boron (B) particle size: at least 98% of the particles pass through a sieve with a mesh size of 0.063 mm total boron (B) 1 d boron amine, in response to the ethanolamine boric acid 8% soluble in water (B) water soluble boron (B) Boron-containing 1E fertilizer solution or suspension and (or) 1 a 1 b , and (or) referred to in paragraph 1 d of the fertilizer solution or suspension in water 2% water soluble boron (B). The fertiliser name indicates its ingredients in water soluble boron (B) 2. Cobalt Cobalt-containing 2A salt obtained chemical, as-salt containing cobalt 19% water soluble cobalt (Co). The fertiliser name indicates with cobalt mineral anion in the associated name, such as cobalt, cobalt chloride sulphate water soluble cobalt (Co) 2B cobalt chelate, cobalt chemically linking with Chelation Builder 2% water soluble cobalt (Co). At least 8/10 of the declared quantity of cobalt (Co) is a chelating manner. Indicate Chelation maker water soluble cobalt (Co). Cobalt chelate form 2 c Cobalt-containing fertilizer solution 2 (a) and (or) 2 b in referred to the fertilizer solution 2% water soluble cobalt (Co). The fertiliser name indicates the anion linked to cobalt and (or) Chelation creator, if any water soluble cobalt (Co). Cobalt chelate form, if applicable 3.3 a Can containing Copper salt For the chemical, as-containing salts can 20% water soluble copper (Cu). The name indicates that the anion of copper, such as copper sulphate in water soluble copper (Cu) 3B copper oxide obtained chemical, as-copper oxide 70% total copper (Cu). Particle size: at least 98% passes through a sieve with a mesh size of 0.063 mm total copper (Cu) 3 c copper hydroxide, chemically derived as-copper hydroxide 45% total copper (Cu). Particle size: at least 98% passes through a sieve with a mesh size of 0.063 mm total copper (Cu) 3D Can chelate is obtained, can chemically bind with Chelation maker 9% water soluble copper (Cu), at least 8/10 of the declared quantity of cobalt (Co) in the form of chelates. Indicate Chelation maker water soluble copper (Cu). Copper Chelation way e May-fertilizer and (or) 3A 3B, 3 c and (or) and (or) 3. referred to in (d) a fertilizer blend 5% total copper (Cu). Indicates if the maker is Chelation Chelation. Specifies the components of the fertilizer total copper (Cu). Water soluble copper (Cu) If this quantity is at least 1/4 the total amount of copper (Cu). Copper Chelation way 3. f can fertilisers containing the solution and (or) 3A 3. referred to in point (d) of the fertilizer solution in water 3% water-soluble copper (Cu) the. The name of the mineral anion indicates that copper (Cu). Indicate Chelation Builder the water-soluble copper (Cu) and the existing form of chelate copper oxychloride 3 g May Get chemically, as-copper oxychloride [Cu2Cl (OH) 3] 50% total copper (Cu). Particle size: at least 98% passes through a sieve with a mesh size of 0.063 mm total copper (Cu) 3 h copper oksihlorīd suspension oksihlorīd suspension of copper water 17% total copper (Cu), total copper (Cu) iron 4 a 4 iron salts containing chemically Derived, as-iron salts containing 12% water-soluble iron (Fe). The name indicates that the anion Fe is linked, for example, iron sulphate, ferric chloride, iron citrate water-soluble iron (Fe) 4B iron chelate, iron chelation, chemically linking it to makers of 5% water soluble iron (Fe), at least 8/10 of the declared quantity is Chelation way Feat. Indicate Chelation Builder water-soluble iron (Fe). Iron chelation therapy in the form of c-4 iron fertiliser solution 4 (a) and (or) 4. referred to in point (b) of the fertilizer solution in water 2% water-soluble iron (Fe). The name of the mineral anion indicate that Fe is bound, and Chelation Builder if there is water soluble iron (Fe). Iron chelation therapy, if any 5.5A Manganese manganese-containing salts obtained by chemical, as-containing salts of manganese (Mn) 17% water soluble manganese (Mn). The name indicates that the anion, Mn is linked, for example, manganese sulphate, manganese chloride in water soluble manganese (Mn) 5. b manganese chelate For chemically linking manganese chelate compounds 5% water soluble manganese (Mn), at least 8/10 of the declared quantity of Chelation of Mn. Indicate Chelation Builder Water soluble manganese (Mn). Manganese chelate form 5 c Manganese oxide produced by chemical, as manganese oxide-40% total manganese (Mn). Particle size: at least 80% to pass through a sieve with a mesh size of 0.063 mm total manganese (Mn) 5 d Manganese-based fertilizer and 5.5 (a) (c) the mixture of fertilizers 17% total manganese (Mn). Name specifies the manganese in fertilizer mixture ingredients total manganese (Mn) water-soluble manganese (Mn), the if it is at least 1/4 of the total quantity of Manganese Mn 5. e-containing fertilizer solution 5 (a) and (or) one 5. referred to in point (b) of the fertilizer solution in water 3% water soluble manganese (Mn). Name specifies the name of the mineral anion and Chelation Builder if there is water soluble manganese (Mn). Manganese chelate form, if applicable 6. Molybdenum 6a sodium molybdate For chemically, as-sodium molybdate 35% water-soluble molybdenum (Mo) the water soluble molybdenum (Mo) 6B ammonium molybdate For chemically, as-ammonium molybdate 50% water soluble molybdenum (Mo) the water-soluble molybdenum (Mo) 6 c Molybdenum-based fertilizer and 6.6 (a) referred to in point (b) of the fertiliser mixture of 35% water soluble molybdenum (Mo). The name indicates the components of a mixture of fertilizer, water soluble molybdenum (Mo) 6 d molybdenum fertilizer in solution containing 6.6 (a) and (or). (b) fertilizers referred to in solution in water 3% water-soluble molybdenum (Mo) the. The name indicates the solution components in the water-soluble molybdenum (Mo) 7. Zinc Zinc-containing 7A salts obtained by chemical, as-containing zinc salts 15% water soluble zinc (Zn). The name indicates that the anion Zn, zinc sulphate water soluble zinc (Zn) zinc chelate 7B For chemically linking zinc Chelation compounds 5% water soluble zinc (Zn), at least 8/10 of the declared quantity are chelate Zn. Indicate Chelation maker water soluble zinc (Zn). Zinc Chelation way 7 c zinc oxide produced chemical, as-zinc oxide 70% total zinc (Zn). Particle size: at least 80% to pass through a sieve with a mesh size of 0.063 mm total zinc (Zn) zinc 7 d fertiliser 7A and 7 c of the fertilizers referred to in a mixture of 30% of the total zinc (Zn). The name indicates a mixture of fertiliser ingredient total zinc (Zn) water-soluble zinc (Zn) maximum, if it is at least 1/4 of the total zinc (Zn) zinc 7 e of fertilizer solution (7A) and (or) one 7. referred to in point (b) of the fertilizer solution in water 3% water soluble zinc (Zn). Name specifies the name of the mineral anion and Chelation Builder if there is water soluble zinc (Zn). Zinc chelate form, if any, of the Liming material F no p. k. The official name of the liming material manufacturing method, as the minimum neutralisation capacity expressed as calcium carbonate (CaCO3) in the equivalent of (% of dry weight) and liming material applicable to the specific requirements of This material, the label or accompanying documents must be declared on the labelling of quality indicators (%) and other requirements 1. Dolomite industrial manufactured karbonātkaļķ liming material, as the calcium and magnesium carbonate, calcium and magnesium oxide, calcium and magnesium hydroxides 105%, about 1 mm in the coarser particles maximum content 5% neutralization capacity, humidity, finer than 1 mm particle content%, calcium (Ca), magnesium (Mg). "The Quick action of liming material" 2. Limestone flour manufactured in liming material, as calcium carbonate – 80%, about 1 mm in the coarser particles maximum content 5% neutralization capacity, humidity, finer than 1 mm particle content%, calcium (Ca), magnesium (Mg). "Slow-release liming material" 3. Partially burned, Malta dolomite manufactured a liming material, as the calcium and magnesium carbonate, calcium and magnesium oxide, calcium and magnesium hydroxide in 85% of coarser particles of 1 mm the maximum content – 5% neutralization capacity, humidity, finer than 1 mm particle content%, calcium (Ca), magnesium (Mg). "The Quick action of liming material" 4. Dolomītmilt industrial produced liming material, as the calcium and magnesium carbonate – 80%, about 1 mm for the coarser particles maximum content 5% neutralization capacity, humidity, finer than 1 mm particle content%, calcium (Ca), magnesium (Mg). "Slow-release liming material" 5. Elektrofiltr dust in the Cement industry's waste, as the calcium oxide and magnesium oxide 70% more, than 1 mm coarser particles maximum content – 1% neutralization capacity, humidity, finer than 1 mm particle content%, calcium (Ca), magnesium (Mg). "The Quick action of liming material" 6. Shale ash industrial waste, as the calcium oxide and magnesium oxide slightly 60%, about 1 mm in the coarser particles maximum content – 3% neutralization capacity, humidity, finer than 1 mm particle content%, calcium (Ca), magnesium (Mg). "The Quick action of liming material" 7. Filtrkaļķ are taken to the sugar industry, as the calcium and magnesium carbonate. Little content, organic matter, nitrogen, phosphorus, potassium or other plant food items 30% neutralization capacity, humidity, finer than 1 mm particle content%, calcium (Ca), magnesium (Mg). "Slow-release liming material" 8. The chalk factory made in liming material as-95% calcium carbonate, the coarser particles of 1 mm the maximum content – 1% neutralization capacity, humidity, finer than 1 mm particle content%, calcium (Ca). "Slow-release liming material" 9. Dolomite sands, the coarse dolomite flour, the dolomitic sand coarse dolomite flour 80% neutralization capacity, humidity, finer than 1 mm particle content%, calcium (Ca), magnesium (Mg). "Slow-release liming material". In addition, you can declare more than 1 mm particle fraction content% 10. Other liming material for any materials not mentioned above, which is useful for soil acidity neutralization and not adversely impact on the soil and plants, as well as a liming material referred to above with coarser grain size distribution of the 20% neutralization capacity, humidity, finer than 1 mm particle content%, calcium (Ca), magnesium (Mg). Indication of the effect of liming material. In addition, you can declare about 1 mm larger size fractions of particulate matter content% note. * Ability To neutralization expressed as calcium oxide (CAO) equivalent, use the factor 0.56. G. Organic fertilizers and organominerāl no p. k. The official name of the fertilizer production method, the basic quality requirements (dry matter, organic matter and plant nutrients, the minimum content (% of natural fertilizer in wet mass) and the applicable specific fertilizer) fertilizer, label or accompanying document must be declared on the labelling of quality indicators (%), and other requirements, as well as additional you can specify plant nutrient content in the dry matter, of 1. Sapropel organic and mineral complex – 10% dry sediment, organic matter – 5% organic matter, total nitrogen (N), total phosphorus (P2O5) total potassium (K2O), humidity, pH of the reaction 2. Poultry manure produced in accordance with Regulation No 1069/2009 and 142/2011 the following processing methods 0.5% (N + P2O5 + K2O). -50% of the dry matter, organic matter – 30% total nitrogen (N), total phosphorus (P2O5) total potassium (K2O), moisture, organic matter, pH reaction 3. Fish meal produced in accordance with Regulation No 1069/2009 and 142/2011 those processing methods, without any other additives 0.5% (N + P2O5 + K2O), and 80% of the dry matter, organic matter 50% total nitrogen (N), total phosphorus (P2O5) total potassium (K2O), moisture, organic matter, pH reaction 4. The horns and hooves of livestock produced in accordance with Regulation No 1069/2009 and 142/2011 those processing methods, without any other additives – total nitrogen (N), total phosphorus (P2O5) total potassium (K2O), moisture, organic matter, pH 5 reaction. Oil seed residues, residue obtained, displacing and (or) extracting oil from the seed and fertilizer for use – total nitrogen (N), total phosphorus (P2O5) total potassium (K2O), moisture, organic matter, the reaction of pH 6. Processed organic fertilizers and organominerāl obtained: 1) preparing fertilizer and organic fertilizer mixtures, including from animal by-products produced in accordance with Regulation No 1069/2009 and 142/2011 those processing methods, and (or) of dried or otherwise processed plant products; 2) of animal by-products produced in accordance with Regulation No 1069/2009 and 142/2011 the following processing methods; 3) earthworms recycling animal by-products, including manure, processed in accordance with Regulation No 1069/2009 and 142/2011 (hereinafter referred to as the worm recycled organic fertilizer); 4) drying or otherwise treating the products of plant origin 0.5% (N + P2O5 + K2O). Solid fertilizers:-10% of the dry matter; -5% organic matter. Liquid fertilizers:-2% of the dry matter; organic substances – 0.3 total nitrogen (N), total phosphorus (P2O5) total potassium (K2O), moisture, organic matter, pH 7 reaction. Solid fertilizers organominerāl with secondary elements and (or) trace elements solid fertilisers obtained from fertilizers and plant organic compounds or animal by-products produced in accordance with Regulation No 1069/2009 and 142/2011 those processing methods, mechanical mixing, and with or without additional processing 0.5% (N + P2O5 + K2O), – 10% of the dry matter, of 5% organic matter, total nitrogen (N) total phosphorus (P2O5) total potassium (K2O), moisture, organic matter, pH, reaction secondary elements and trace elements in accordance with the provisions of annex 4 and 8. Liquid fertilizers in organominerāl with secondary elements and (or) trace elements in liquid fertilisers, which are used in the manufacture of fertilizers and animal by-products that are produced in accordance with Regulation No 1069/2009 and 142/2011 those processing methods, or herbal organic compounds 0.5% (N + P2O5 + K2O) 2%, dry matter, organic matter – 0.3 total nitrogen (N). If any of the forms of nitrogen is more than 1%, it declares. Total phosphorus (P2O5) total potassium (K2O), dry matter, organic matter, pH, reaction secondary elements and trace elements in accordance with the provisions of annex 4 and 11 comments. 1. Organic Fertilizer – material that contains carbon, hydrogen and oxygen, and in addition at least one or more of the plants necessary nutrients. 2. Organominerāl fertilizers, organic fertilizers and compound fertilizers, which is obtained in a single technological process or these components mechanical mixing. 3. Processed organic fertilizer: any organic (plant or animal) origin, fertilizer, chemical, physical, or modified from its original state, including earthworms from organic raw materials. On the packaged organic fertilizers are applied legislation for processed organic fertilizers. H. special fertilizers for use no. p. k. The official name of the fertilizer production method, the basic quality requirements (plant nutrient minimum content (% by weight of the fertilizer), and applicable to the specific fertilizer) fertilizer, label or accompanying document must be declared on the labelling of quality indicators (%) and other requirements 1. NPK fertilizer with trace elements or free ones and (or) secondary feed elements, chemical or mechanical mixing and (or) dissolved in water, trace elements and secondary NPK plant nutrient-containing components. Stable atmosphere, contains no animal or vegetable organic compounds 4.5% (N + P2O5 + K2O), 1% of the total nitrogen (N), 1% water soluble phosphorus (P2O5) water soluble 1.21% potassium (K2O) total nitrogen (N), water soluble phosphorus (P2O5) water soluble potassium (K2O), trace elements and secondary plant nutrient content 2. PK fertilizer with trace elements and (or) secondary feed elements, chemical or mechanical mixing and (or) water dissolving Fri, trace elements and secondary plant nutrient-containing components. Stable atmosphere, contains no animal or vegetable organic compounds 3.5% (P2O5 + K2O), 1% water soluble phosphorus (P2O5) water soluble 1.21% potassium (K2O) water soluble phosphorus (P2O5) water soluble potassium (K2O), trace elements and secondary plant nutrient content 3. NK fertilizer with trace elements and (or) secondary feed elements, chemical or mechanical mixing and (or) dissolved in water, trace elements and the PROPORTION of the secondary plant nutrient-containing components. Stable atmosphere, contains no animal or vegetable organic compounds 2.21% (N + K2O) 1% of the total nitrogen (N), 1.21% water soluble potassium (K2O) total nitrogen (N), water soluble potassium (K2O), trace elements and secondary plant nutrient content 4. N fertilizer with trace elements and (or) secondary feed elements, chemical or mechanical mixing and (or) dissolved in water, trace elements and secondary plant nutrient-containing components. Stable atmosphere, contains no animal or vegetable organic compounds 1% total nitrogen (N) total nitrogen (N), micro-nutrients and secondary plant nutrient content 5. NP fertilizers with trace elements and (or) secondary feed elements, chemical or mechanical mixing and (or) dissolved in water, trace elements and NP secondary plant nutrient-containing components. Stable atmosphere, contains no animal or vegetable organic compounds 3.29% (N + P2O5), 1.0% total nitrogen (N), 1% water soluble phosphorus (P2O5) total nitrogen (N), water soluble phosphorus (P2O5), trace elements and secondary plant nutrient content 6. Secondary elements and (or) trace element mixture (solution, suspension, emulsion), chemical and dissolved trace elements in water and (or) secondary elements containing components trace elements and secondary plant nutrient content 7. Hard mixture of trace elements (solid product), chemical or mechanical mixing and (or) dissolve in water and micro secondary elements containing trace components in the total content and the content soluble in water. Trace elements in the form of chelation therapy, if any. 8. Mikroelementumaisījum (solution, suspension, emulsion), chemical and dissolved in water and micro secondary elements containing components for each trace element contents 9. NPK fertilizers with or without secondary and (or) trace elements and organic compounds, chemical and (or) dissolved in water NPK and (or) trace elements, and (or) secondary elements and organic compounds containing components. liquid (solutions, suspensions, emulsions), or solid fertilisers, which are used in the manufacture of fertilizers and plant or animal origin component of organic compounds not more than 3% natural material in the main element, trace element and secondary elements , organic matter, pH, humidity, or reaction of the dry note. * Special meaning fertilizers, fertilizers that are designed for a specific purpose (cover areas, gardens, lawns, houseplants, forestry, etc.) or any crops, using specific methods (ārpussakņ fertilizer, watering, etc.). I. microbiological preparations no p. k. The official name of the fertilizer production method and fertilizers as Microbiological preparation of labelling or marking the quality indicators and declared other requirements 1. Azotobacter product made of a pure bacterial culture of the micro-organism scientific name, plate the quantity CFU/ml or cfu/* 2. Mikoriz product contains fungal cultures, which improve the nutrient intake of certain groups of plants and micro-organisms of the genus scientific name, plate the quantity CFU/g or CFU/ml 3. Micro-organisms-based products are produced using natural environment isolated from one or more pure micro-organism mixtures. Added substances, ensuring the viability of the micro-organism and optimal storage conditions for micro-organisms scientific name, plate the quantity CFU/g or CFU/ml note. * CFU-colony forming units. J. atypical fertilisers and plant growth promoters no p. k. The official name of the fertilizer production method and fertilizers as quality requirements (plant nutrient minimum content (% by weight of the fertilizer), and applicable to the specific fertilizer) fertilizer, label or accompanying document marking the quality indicators to be declared 1. Atypical fertilisers production by-products or products obtained by chemical or mechanical mixing and (or) dissolve the components in water, containing one or more plant nutrients, or suspension components for gaseous environment. If the production process used for animal by-products, they must be produced in accordance with Regulation No 1069/2009 of the following processing methods (N + P2O5 + K2O) less than 0.5% total nitrogen (N), total phosphorus (P2O5) total potassium (K2O). Fertilisers containing plant or animal materials: 1) humidity; 2) organic matter. The pH of the reaction (optional). Secondary elements and trace elements (optional) 2. Plant growth promoter chemical or mechanical, as well as by-products (etc.) that contains the biologically active compounds in solid or liquid fertilizer, the total nitrogen (N), total phosphorus (P2O5) total potassium (K2O), moisture, organic matter, pH of the reaction. Secondary elements and trace elements, if their content is declared to comply with the provisions of annex 4 and 11. The biologically active connection notes. 1. Atypical fertiliser – fertilizer that contains less than 0.5% of nitrogen, phosphorus and potassium (summary, natural wet), but at least its use, a 10% increase in yields. 2. a plant growth promoter – a product that contains one or more of the chemical elements that are recognized as the plants need and also one or more biologically active compounds and which, in accordance with the recommended dose of fertilizer is used mainly for plant growth promotion, rather than the supply of plant nutrients. K. substrate no p. k. The official name of the substrate, method of production, the quality of raw material of the substrate (substrate moisture and other applicable specific requirements) substrate, label or accompanying document must be declared on the labelling of quality indicators (%) and other requirements 1. Peat substrate turf, which is incorporated into this material, and fertilizers, as well as possible ingredients that enhance the substrate structure and physical properties, or briquettes and pills from the turf, except for components that contain other organic raw materials of up to 65% maximum moisture, electrical conductivity (EC) pHKCl, mS/cm calcium (Ca), magnesium (Mg), humidity,%, a fraction of the size (mm) 2. Organic soil substitute mixture containing dung, compost, animal origin raw materials processed in accordance with Regulation No 1069/2009 and 142/2011, or peat and other components for maximum moisture-65% pHKCl, electrical conductivity (EC), mS/cm, organic substances (%), total nitrogen (N), total phosphorus (P2O5) total potassium (K2O), humidity (%) 3. Inorganic substrate jonapmaiņ resin, gel or clay granules, which are impregnated with nutrients, pHKCl, electrical conductivity (EC), mS/cm, total nitrogen (N), total phosphorus (P2O5) total potassium (K2O) 4. Inert substrates in mineral wools, perlite, vermiculite, expanded, granite chips, synthetic materials, as well as foam and fibre, coir, Perlite, vermiculite and expanded – granular or fraction of the size (mm from-to). Mineral: pHKCl (10% of the water extract from substrate), electrical conductivity (EC), mS/cm. Perlite, vermiculite, expanded, a granite fragment-size fraction. Coir substrate-humidity (%), KCl, pH/conductivity (EC), mS/cm of Agriculture Minister John Dūklav annex 2 Cabinet 1 September 2015 regulations no 506 tolerable negative deviations from the declared fertiliser and substrate quality Nr. p. c. Fertilisers and substrates and their quality scores declared permissible deviations from the declared quality characteristics (mass, unless otherwise indicated) 1. Nitrogen fertilizers, total nitrogen (N) 1.1. calcium nitrate 0.4 1.2. calcium-magnesium nitrate 0.4 1.3. sodium nitrate (acquired by chemical) 0.4 1.4. Chile nitre (of the nuggets produced sodium nitrate) 0.4 1.5. calcium cyanamide 1.0 1.6. nitrate-containing calcium cyanamide 1.0 1.7. ammonium sulphate 0.3 1.8. ammonium nitrate 1.8.1. the total nitrogen content of up to 32% (including) 0.8 1.8.2. the total nitrogen content of over 32% 0.6 1.2. -of calcium ammonium nitrate 0.8 1.10. ammonium sulphate-nitrate 0.8 1.11. ammonium-magnesium sulphate-nitrate 0.8 1.12. magnesium-ammonium nitrate 0.8 1.13. urea 0.4 1.14. urea-ammonium sulphate 0.5 1.15. nitrogen fertilizer solution 0.6 1.16. ammonium nitrate-urea solution 0.6 1.17. calcium nitrate suspension 0.4 1.18. liquid nitrogen fertilizers (solution, suspension) with urea formaldehyde 0.4 1.19. ammonia is 0.3 1.20. anhydrous ammonia 1.1 2. Phosphorus fertilizers 2.1. soluble in mineral acids of phosphorus (P2O5) 2.1.1. superfos is 0.8 2.1.2. aluminium-calcium phosphate 0.8 2.1.3. soft to 0.8 2.1.4. phosphorous slag 1.0 2.2. formic acid-soluble phosphorus (P2O5) 2.2.1. soft to 0.8 2.3. neutral ammonium citrate soluble phosphorus (P2O5) 2.3.1. simple superphosphate 0.8 2.3.2. concentrated superphosphate 0.8 2.3.3. Double superphosphate 0.8 2.4. alkaline ammonium citrate soluble phosphorus (P2O5) 2.4.1. precipitāt 0.8 in 2.4.2. calcium 0.8 termofosfāt for 2.4.3. aluminium-calcium phosphate 0.8 2.5. the citric acid soluble phosphorus (P2O5) 2.5.1. phosphorous slag 0.8 2.6. water soluble phosphorus (P2O5) 2.6.1. simple superphosphate 0.9 2.6.2. concentrated superphosphate 0.9 2.6.3. superfos is 0.9 2.6.4. Double superphosphate 1.3 3. Potassium (K2O) fertilizers 3.1. Kainite 1.5 3.2. rich salt 1.0 kainīt 3.3. potassium chloride 3.3.1. with potassium (K2O) content that does not exceed 55% 1.0 3.3.2. with potassium (K2O) content exceeding 55% 0.5 3.4. magnesium-potassium chloride 1.5 3.5. potassium sulphate 0.5 3.6. magnesium-potassium sulphate 1.5 4. Complex fertilizers (chemical) 4.1. nitrogen (N) 1.1 4.2. phosphorus (P2O5) 1.1 4.3. potassium (K2O) 1.1 4.4. N + P2O5 + K2O 4.4.1. the fertilizer firm 1.5 4.4.2. three fertilizer 1.9 5. Complex fertilizers (for mechanical, blending NPK and more components containing) 5.1. nitrogen (N) 2.2 5.2. phosphorus (P2O5) 2.2 5.3. potassium (K2O) 2.2 5.4. N + P2O5 + K2O 5.4.1. the fertilizer firm 3.0 5.4.2. three fertilizer 3.8 6. Secondary plant nutrients fertilizers (except mechanical mixtures) 6.1. magnesium (Mg) 1/4 of the declared content, but not exceeding 0.55 6.2. calcium (Ca) 1/4 of the declared content not exceeding 6.3 0.64. sodium (Na) 1/4 of the declared content, does not exceed 0.67 a 6.4. sulphur (S) 1/4 of the declared content not exceeding 0.36 7. Secondary plant nutrient elements in compound forms 7.1. magnesium (Mg) 1/3 of the declared content not exceeding 1.10 7.2. calcium (Ca) 1/3 of the declared content not exceeding 1.28 7.3. sodium (Na) 1/3 of the declared content not exceeding 1.34 7.4. sulphur (S) 1/3 of the declared content not exceeding 0.72 8. Trace elements fertilizer (except mechanical mixtures) 8.1. trace-element B, Co, Cu, Fe, Mn, Mo and Zn content exceeding 2% 0.4 8.2. trace-element B, Co, Cu, Fe, Mn, Mo and Zn content does not exceed 2 1/5 of the declared content of 9. Trace elements in compound motor 9.1. trace-element B, Co, Cu, Fe, Mn, Mo and Zn content exceeding 2% 0.8 9.2. trace-element B, Co, Cu, Fe, Mn, Mo and Zn content not exceeding 2/5, 2% of the declared content is 10. Other items 10.1. chlorine (Cl) 0.2 11. Liming materials 11.1. neutralization capacity expressed as calcium carbonate (CaCO3) equivalent (%) 1/20 of the declared size 12. Organic fertilizers and organominerāl 12.1. sapropel 12.1.1. total nitrogen (N) 1/5 of the declared content 12.1.2. total phosphorus (P2O5) 1/10 of the declared content of 12.1.3. total potassium (K2O) 1/5 of the declared content of 12.2. the horns and hooves of livestock 12.2.1. total nitrogen (N) 0.5 12.3. oil seeds Marc 12.3.1. total nitrogen (N) 0.5 12.4. fish meal 12.4.1. total nitrogen (N) 0.5 12.5. poultry manure 12.5.1. total nitrogen (N) 1/5 of the declared content 12.5.2. total phosphorus (P2O5) 1/10 of the declared content 12.5.3. total potassium (K2O) 1/5 of the declared content of 7.8. other organic manure 12.6.1 and organominerāl. total nitrogen (N) 1/2 of the declared content 12.6.2. total phosphorus (P2O5) 1/2 of the declared content 12.6.3. total potassium (K2O) 1/2 of the declared content 13. 13.1 the substrate. total nitrogen (N) 1/2 of the declared content is 13.2. total phosphorus (P2O5) 1/2 of the declared content of 13.3. total potassium (K2O) 1/2 of the declared content of 13.4. electrical conductivity 0.4 ECU 13.5. the reaction of (pHKCl) 0.3 13.6. humidity is 1/4 of the declared content of 8.5. organic matter 1/4 from the declared content of 13.8. the size of the fraction 1/4 of the declared quantity of 13.9 fraction. calcium 1/4 of the declared content of 27.40. magnesium 1/4 of the declared content of 14. Granulometry in accordance with Cabinet of Ministers on 1 September 2015 rule no. 506 "fertiliser and substrate identification, quality, conformity assessment, and trade rules" 1. Annex 1/20 of the declared quantity 15. Plant growth promoters 15.1. biologically active compounds 1/2 of the 16 declared content. Microbiological preparations 16.1. specific plate quantity 1/2 of the Group of the declared number of notes. 1. The permissible deviations are necessary to take account of fluctuations in the quality of fertilizers, fertilizer production, processing, sampling and testing. 2. various forms of nitrogen (NO3, NH4, etc.) and various solvents, soluble phosphorus (P2O5) content in declared permitted deviation is 1/10 of the total content, maximum deviation-two per cent of the total weight, if the plant nutrient element content conforms to the Cabinet on 1 September 2015 rule no. 506 "fertiliser and substrate identification, quality, conformity assessment, and trade rules (hereinafter rules) referred to in annex 1 and in the annex shows the adverse deviation. 3. the Provisions of section H of annex 1 of these fertilizers, plant nutrient content declared permissible deviation is mass 0.4 percent, if the element content of fertilizer exceeding 2%, and 1/5 of the declared content for the element content of the fertilizer does not exceed 2%. 4. If this annex does not otherwise specified, it declared admissible in the negative deviation is 1/5 of the declared value. Agriculture Minister John Dūklav in annex 3 of the Cabinet on 1 September 2015 regulations no 506 unwanted impurity maximum level substrate fertilizer and no p. k. Fertilizer or substrate unwanted impurities in the maximum allowable concentration (expressed as dry sample of the absolute), unless otherwise specified by the method of determination 1. Ammonium nitrate with high (more than 28%) the nitrogen content of copper 10 mg/kg hlorūdeņražskāb, which determines the density at 20 ° c is 1.18 g/ml of 0.02% weight by chlorine down the water extract 2. Phosphorus fertilizers containing cadmium (Cd) 60 mg Cd/kg P2O5 down the aqua regia extract 3. Organic and organominerāl fertilizers and liming materials, not the typical fertilizers and plant growth promoter for mercury (Hg) 2.0 mg/kg determine aqua regia cadmium (Cd) in the extract 3.0 mg/kg down the aqua regia extract arsenic (As) 50 mg/kg determine aqua regia nickel (Ni) extract 100 mg/kg determine aqua regia lead (Pb) in the extract 150 mg/kg in the aqua regia extract Determined 4. Organic and organominerāl fertilizers, atypical fertilisers and plant growth promoters and Enterococacea of Escherichia coli 1000 CFU/g or 1000 CFU/ml salmonella (1) 25 g of product samples in plastic, glass or metal particles that are larger than 4 mm (2) 0.5% weight by 5. Microbiological preparations of Escherichia coli and the 1000 cfu/g or Enterococacea 1000 CFU/ml salmonella (3) 25 g sample of the product not found 6. Substrate mercury (Hg) 1.0 mg/kg determine aqua regia cadmium (Cd) in the extract 2 mg/kg determine aqua regia extract arsenic (As) 20 mg/kg determine aqua regia nickel (Ni) extract 50 mg/kg determine aqua regia lead (Pb) in the extract 100 mg/kg determine aqua regia extract copper (Cu) 100 mg/kg determine aqua regia zinc (Zn) extract 300 mg/kg of the extract Determine aqua regia chromium (Cr) 100 mg/kg determine aqua regia extract of Escherichia coli and Enterococacea (4) 1000 CFU/g salmonella (5) 25 g in samples of the product is not found foreign objects (glass, metal, plastic, bone, stones) (6) mass 0.5 percent notes. (1) determine if the fertiliser contains raw materials of animal origin. (2) determine if the fertilizer is in solid form. (3) lays down the microbiological preparation which is used in the production of the raw materials of animal origin. (4) determine the substrate containing organic origin (except for jonapmaiņ and inert inorganic substrate). (5) determine the substrate containing raw materials of animal origin. (6) determine substrate solid forms (except for jonapmaiņ and inert inorganic substrate). Agriculture Minister John Dūklav in annex 4 of the Cabinet on 1 September 2015 regulations no 506 minimum the declared content of trace elements fertilizer 1. minimum micro-nutrient the declared content (%) in the fertilizer is: 1.1. trace elements containing only hard or liquid mixtures: 1. in the table. p. k. Trace elements in mineral form chelated trace elements or kompleksēt 1. Boron (B) 0.20 0.20 2. Cobalt (Co) 0.02 0.02 3. Copper (Cu) 0.50 0.10 4. Iron (Fe) 2.00 0.30 5. Manganese (Mn) 0.50 0.10 6. Molybdenum (Mo) 0.02-7. Zinc (Zn) total trace 0.50 0.10 1.1.1. the minimum quantity of content in compound hard (mikromēslo), which only contains trace elements,-5% by weight; 1.1.2. the total trace element content in minimum quantity liquid mixtures (mikromēslo), which only contains trace elements,-2% of the mass; 1.2. fertilizers containing major and/or secondary plant nutrient elements with trace elements: table 2 No. p. k. Trace elements to the soil Incorporation of agricultural crop spraying the leaves or grass gardening in the 1. Boron (B) 0.010 0.010 0.010 2. Cobalt (Co) 0.002-0.002 3. 0.010 0.002 0.002 copper (Cu) 4. Iron (Fe) 0.500 0.020 0.020 5. Manganese (Mn) 0.100 0.010 0.010 6. Molybdenum (Mo) 0.001 0.001 0.001 7. Zinc (Zn) 2 most common 0.010 0.002 0.002. trace element chelate-Builder abbreviations: No. p. k. The name of the designation of the chemical formula 1. EDTA C10H16O8N2 2 ethylenediaminetetraacetate. 2-3 hidroksietilēndiamīntetraetiķskāb of heedta C10H18O7N2. Dietilēntriamīnpentaetiķskāb-dtpa C14H23O10N3 4. Ethylenediamine-N, N '-di [(Ortho-hydroxyphenyl) acetic acid] [o o] of 5. C18H20O6N2 EDDH Ethylenediamine-N-[(Ortho-hydroxyphenyl) acetic acid]-N [(para-hydroxyphenyl) acetic acid] [o, p] EDDH C18H20O6N2 of 6. Etildiamīn-N, N ' di [(Ortho-hydroxy-methyl-phenyl) acetic acid] [o o] EDDHM-C20H24O6N2 7. Ethylenediamine-N-[(Ortho-hydroxy-metilfenil) acetic acid]-N [(para-hydroxy-metilfenil) acetic acid] [o, p] EDDHM of C20H24O6N2 8. Ethylenediamine-N, N '-di [(5-carboxy-2-hydroxyphenyl)] acetic acid EDDCH the C20H20O10N2 9. Ethylenediamine-N, N '-di [(2-hydroxy-5-sulfofenilfenil)] acetic acid] and its condensation products of C18H20O12N2S2 + n * EDDHSA (C12H14O8N2) 10. I-hidroksietilidendifosforskāb-C2H8O7P2 Minister of Agriculture John OEDF Dūklav annex 5 cabinet 1 September 2015 regulations no 506 and substrate fertilizer registration submission.     .                             day month year i. General information 1. Fertilizer or substrate applications for registration submitted (mark with x required) manufacturer importer Packager 2. Applicant's registration number in the register of the competent institution 3. Applicant: 3.1 3.2 name registered office 3.3. phone number fax number e-mail address 4. details of person submitting application: 4.1 a personal code             -4.2. name surname 4.4 4.3 identity documents in the data (to be completed if there is no ID code): the name of the issuing authority 4.4.1 4.4.2 4.4.3. number. date of issue 5. Fertiliser manufacturer or the manufacturer of the substrate: 5.1 5.2 5.3 the name address telephone number fax number e-mail address 5.4. manufacturer's registration number in the register of the competent institution (II). information on fertilizer or substrate 6. Type (Group) A Simple B-complex fertilizers fertilizers fertilizers Liquid (C) (D) only the secondary plant nutrients fertilizers containing E Only products containing trace elements fertilizer features F G organic materials of Liming and fertilizers organominerāl H fertilizers I use special microbiological preparations J atypical fertilizers and plant growth promoters K substrates 7. Name: 7.1 7.2 the official name trade name 8. Method of production 9. Inputs 10. Indications for use 11. expected chain of fertilizer production into the packing trade 12. State fee payment date confirm that the information provided is correct (application for registration of the applicant, name and signature) Note. The document property "signature" does not fill in, if an electronic document is drawn up according to the law on electronic document design. Agriculture Minister John Dūklav in annex 6 Cabinet 1 September 2015 regulations no 506 State plant protection service investigator trials: (scientific name) (scientific institutions address) certificate of atypical fertilizer, plant growth promoters or the efficiency of the preparation of microbiological fertilizer fertilizers producer name (name, address) the trial venue/s (address/-I) information on the fertilizer efficiency of trial: Crop, having undergone the test of the effectiveness of the fertilizer pilot year (cover the area of trials – harvest cycles) trial period of harvest increase% found in experimental that respects differences in principle only certify that the reported test results are discussed in a scientific institution and collegiate deemed appropriate for submission to the Latvian State plant protection service.
Title (name) (signature).     .                             day month year of Agriculture Minister John Dūklav in annex 7 of the Cabinet on 1 September 2015 regulations no 506 Latvia produced a mechanical mixture of fertilizers in the registration submission.     .                             day month year i. General information 1. mechanical mixture of fertilizers application submitted for registration (required mark with x) Packer draftsman of the mixture 2. Applicant's registration number in the register of the competent institution 3. Applicant: 3.1 3.2 name registered office 3.3. phone number fax number e-mail address 4. details of person submitting application: 4.1-4.2. ID code name surname 4.4 4.3 identity documents in the data (filling out If no ID code): the name of the issuing authority 4.4.1 4.4.2 4.4.3. number. date of issue 5. Fertiliser producer or preparer of the mixture: 5.1 5.2 5.3 the name address telephone number fax number (II). information on fertilizer 6. Name: official name 6.1 6.2 name 7. mechanical components of a mixture, the name of (official and trade, if any) composition (%)  The number of the registration certificate (EC fertilisers – producer) 8. Declared plant nutrients (), their forms and šķīdība1 9. indication for use 10. expected chain of fertilizer mixture preparation packing trade Certifying that the information provided is correct (the registration applicant's first name, last name and's signature2) Note 1 in accordance with the Cabinet of Ministers on 1 September 2015 rule no. 506 "fertiliser and substrate identification quality, conformity assessment, and trade provisions "column of annex 1. 2 document property "signature" does not fill in, if the electronic document is drawn up according to the law on electronic document design. Agriculture Minister John Dūklav in annex 8 Cabinet 1 September 2015 regulations no 506 (enhanced small national coat-of-arms) in the Ministry of Agriculture of the Republic of Latvia State plant protection service of the fertilizer registration certificate No. ____ 1.  The name of fertiliser (fertilizer identification requirements) (trade name of fertilizer) 2.  Fertilizer composition (%)                       3. The fertiliser manufacturer 4.  The fertilizer chain (specify desired – production, packaging, import, production, marketing) 5. Fertilizer nutrient data nutrient elements of Plant form content (%)                                    
 Other data declared certificate issued (specify owner) date of issue of the licence for the national plant protection services officer (name and signature) Note URZ.v.*. the document properties "date", "signature" and "Z.v." does not fill in, if the electronic document is drawn up according to the law on electronic document design.
Agriculture Minister John Dūklav 9. attachment Cabinet 1 September 2015 regulations no 506 (enhanced small national coat-of-arms) in the Ministry of Agriculture of the Republic of Latvia's national plant protection services in microbiological preparation registration certificate No. ____ 1. Microbiological preparation name (according to the microbiological preparations identification requirements) (microbiological preparations the trade name) 2. Microbiological preparation manufacturer 3. Microbiological preparation chain (specify desired-production, import, marketing) 4. Microbiological preparation data declared in the scientific name (genus species, strain, as well as, if one has been identified) plate count (CFU/g or CFU/ml) 5. other data declared 6. Field of use License was issued (specify owner) date of issue of the licence for the national plant protection services officer (name and signature) Note URZ.v.*. the document properties "date", "signature" and "Z.v." does not fill in, if the electronic document is drawn up according to the law on electronic document design. Agriculture Minister John Dūklav 10. attachment Cabinet 1 September 2015 regulations no 506 (enhanced small national coat-of-arms) in the Ministry of Agriculture of the Republic of Latvia's national plant protection services of the substrate registration certificate No. ____ 1.  The name of the substrate (substrate identification requirements) (trade name of the substrate) 2.  Substrate materials (%)              3. Substrate manufacturer 4.  Substrate chain (specify desired – manufacturing, importation, packaging, marketing) 5. Substrate data Declared to be declared the numerical value of a measurement certificate issued (specify owner) date of issue of the licence for the national plant protection services officer (name and signature) Note URZ.v.*. the document properties "date", "signature" and "Z.v." does not fill in, if the electronic document is drawn up according to the law on electronic document design. Agriculture Minister John Dūklav 11. Annex Cabinet 1 September 2015 regulations no 506 application for fertiliser and substrate, who recognised in another Member State of the European economic area.     .                             day month year i. General information 1 the applicant's registration number in the register of the competent institution by the applicant: 2 2.1. name, registered office 2.2 2.3. telephone number fax number e-mail address 3. details of person submitting application: 3.1-3.2 of personal code name surname 3.4 3.3 identity document data (filled in if no ID code): the name of the issuing authority 3.4.1 3.4.2 3.4.3. number date of issue (II). information on the fertiliser and substrate 4. Member State that is recognised by the fertiliser and substrate sales in your country: National 4.1 4.2 4.3 the supernaturalists (name). period of validity of the opinion (if any) 5. Fertilizer or substrate manufacturer and the competent authority approval number 6. Fertilizer or trade name of the substrate, 7. The fertiliser and substrate Group (if it is specified in the certificate of the Member) 8. Date of payment for services, certify that the information provided is correct (the name of the applicant for registration first name, last name and signature) Note. the document property "signature" does not fill in, if an electronic document is drawn up according to the law on electronic document design. Agriculture Minister John Dūklav 12. attachment Cabinet 1 September 2015 regulations no 506 labelling or marking and accompanying information appearing on fertiliser 1. Fertilizer registration certificate number or authorization number. 2. the official name of the fertilizers in accordance with Cabinet of Ministers on 1 September 2015 rule no. 506 "fertiliser and substrate identification, quality, conformity assessment, and trade rules" (hereinafter referred to as the rules) and annex 1 of the fertilizer trade name (if any). Fertilizer trade name must not conflict with the content and method of production. 3. requirements for the official name of the fertilizer: 3.1 where fertilizers contain two or three major plant nutrients (nitrogen, phosphorus, potassium), the name is "Compound fertiliser". Plant nutrient elements are indicated by names or chemical symbols. Mechanical mixture name references the "mechanical mixture"; 3.2. If the fertiliser contains: 3.2.1. key plant nutrient elements and one or more secondary plant nutrient elements (such as calcium, magnesium, sodium, sulphur), the official name is "Content" and the secondary item names or chemical symbols; 3.2.2. key plant nutrient elements and one or more trace elements (e.g., boron, cobalt, copper, iron, manganese, molybdenum, zinc), the official name is "With" or the word "trace elements" and trace elements With names or chemical symbols; 3.2.3. number of trace element salts mixture, the official name is "the mixture of trace elements"; 3.3. If the fertilizer packaging is less than 1 kg (or 1000 ml) where the fertilizer, the name on the label of the specific secondary plant nutrient and trace element names and chemical symbols can specify label pointer declared section. 4. plant nutrient composition. Plant nutrient content of the numeric value indicates the essential composition: phosphorus (P2O5) and potassium (K2O)-oxide, in the form of other plant nutrients-in the form of elements: nitrogen (N), calcium (Ca), magnesium (Mg), sodium (Na), sulfur (S), chlorine (Cl), boron (B), cobalt (Co), copper (Cu), iron (Fe), manganese (Mn), molybdenum (Mo), zinc (Zn). These conditions also apply to fertilizers, which are marked "EC fertiliser". 5. plant nutrient elements in accordance with the provisions of annex 1 of the 5 box declares, subject to the following conditions: 5.1 if the calcium, magnesium, sodium and sulphur content of not less than 1.2% 1.4% Ca, Mg, Na, 2.2% and 2.0% S; 5.2. declare one or more of the content of trace elements in trace elements in solid or fluid mixtures of salts, as well as fertilisers for main or secondary plant nutrient supply, if the content in the fertilizer shall be not less than the provisions specified in annex 4; 5.3. the declared pointer section shows the solubility of trace elements, that is, whether the specified value is the total or trace elements soluble in water; 5.4. where fertilizers contain trace elements of complex compounds organominerāl, declared in the section behind the name of the trace elements and the legend are "chelated by" and the designation of the makers of chelation therapy in accordance with annex 4, paragraph 2. 6. Raw materials (fertilizers containing animal or plant origin, organic compounds). 7. Guidance on the use of fertilizers. Fertilizers containing only trace elements, as well as plant growth promoters are "attention! Over rate of use can be harmful ". 8. Indication of the fertilizer storage (in accordance with the safety data sheet, if any). Liquid fertilizers, indicate the storage temperature and other special requirements. Fertilizer feature indicates the storage period, if any. 9. Indication of the danger of fertilizer in accordance with the laws and regulations governing chemical and chemical product classification, labelling and packaging. 10. Animal organic and organominerāl fertilizers, the label is "agricultural animals must not be cut or use of grass crops for at least 21 days after treatment. 11. the guaranteed net mass of solid fertilizers and guaranteed weight (or volume) of the liquid fertilizers. If the gross weight (or volume), also indicate the weight or volume of packing. 12. If the fertiliser has been issued a certificate of compliance with the labelling of fertilizer or labelling with the indication "organic farming", the label of the fertilizer or used the label "organic farming", or "allowed to use organic farming" and indicate the code of control authorities, which issued the certificate with the certificate. 13. The fertilizer manufacturer's and importer's name and address. Packer, importer of the manufacturer and the name and address of the packer. The notes. 1. Phosphorus and potassium content for conversion to oxide of the element uses the following formula: 1.1. phosphorus (P) = phosphorus oxide 2.291 x (P2O5); 1.2. potassium (K) × 1.205 = potassium oxide (K2O). 2. calcium, magnesium, sodium and sulphur content of oxides on the conversion of the element uses the following formula: 2.1 (MgO) × 0.603 = magnesium (Mg); 2.2 (CAO) × 0.715. = calcium (Ca); 2.3 (Na2O) × 0.742. = sodium (Na); (SO3) × 0.400 2.4 = sulfur (S). 3. the provisions of annex 1, section H of the fertilizers of declared section you can specify the secondary plant nutrient elements whose content is less than 12 rules. in paragraph 5.1 of the annex to the specified content, and trace elements whose content is less than the rules specified in annex 4, the mandatory indication of the contents of this plant nutrient content. Agriculture Minister John Dūklav 13. attachment Cabinet 1 September 2015 regulations no 506 labelling or information appearing on the label of the microbiological preparations 1. Microbiological preparation of registration certificate or certificate number.
2. the official name of the microbiological preparations in accordance with the Cabinet of Ministers on 1 September 2015 rule no. 506 "fertiliser and substrate identification, quality, conformity assessment, and trade rules (hereinafter rules) Annex 1 and microbiological preparations the trade name (if any). The microbiological trade name of the preparation, must not conflict with the content and method of production. 3. The declared indicators in accordance with the provisions of title I of annex 1 "microbiological preparations" box 4:3.1 microbiological preparations of micro-organisms of the scientific name (genus, species, strain, and if any are identified); 3.2. plate the quantity is expressed as CFU/g or CFU/ml (CFU-colony-forming units). 4. Guidance on microbiological preparation. 5. Indication of the plant species, genera, plant groups, or for the renewal of the microbiological process activation and regulation of the soil or other substrate that microbiological preparation. 6. Guidance on microbiological preparation and storage (storage temperature and storage period) and other special requirements (in accordance with the safety data sheet, if any). 7. preparation of microbiological guaranteed net weight or volume. If the gross weight (or volume), also indicate the packaging (containers), mass or volume. 8. Microbiological preparation the manufacturer and the name and address of the importer. Minister of agriculture John Dūklav. Annex 14 cabinet 1 September 2015 regulations no 506 labelling or information appearing on the label of the substrate Substrate 1 registration certificate number or authorization number. 2. the official name of the substrate under the Cabinet on 1 September 2015 rule no. 506 "fertiliser and substrate identification, quality, conformity assessment, and trade rules" (hereinafter referred to as the rules) and substrate annex 1 trade name, if any. Trade name of the substrate must not be in conflict with its content and method of production. 3. The declared indicators in accordance with the provisions of section K of annex 1 of the 5 box. 4. Raw materials. 5. the peat substrate, peat decomposition degree after Korean Posts. 6. If the substrate contains other plants feed elements, you can specify the label for the section to be declared. 7. The indications of the substrate storage (storage temperature and storage period) and use. 8. Guarantee the characteristic turf substrate, organic soil substitute for and for jonapmaiņ of inorganic substrate. 9. packaging volume. 10. The substrate manufacturer and the name and address of the importer. Packer, importer of the manufacturer and the name and address of the packer. 11. the year and month of manufacture. Agriculture Minister John Dūklav 15. attachment Cabinet 1 September 2015 regulations no 506 (enhanced small national coat-of-arms) in the Ministry of Agriculture of the Republic of Latvia, the national plant protection service Permission No. _____ ____ ____ ____ ____ ____ ____ ____ ____ (name) 1. The fertilizer or the substrate name: 1.1. the official name (if any) 1.2. trade name (if applicable) 2. The fertilizer or substrate type 3. The fertilizer or the substrate manufacturer, State 4. The declared indicators 5. Packaging (net weight or volume) 6. The fertilizer or the substrate chain 7. The fertilizer or the quantity of the medium (if provided to specify) 8. The fertilizer or the lot number of the substrate (if intended to specify) 9. Permit issued to: 9.1. the name of the permit holder 9.2. the address of the permit holder 10. Date of adoption of the decision and the number 11. Permit valid until the authorization included in the fertilizer or the substrate gaita1 of entry date of importation 12.13. quantity Imported 14. Remainder of the permitted quantity 15. Customs document type, number, date 16. Customs officers last name, signature, stamp, stamp of the Customs national plant protection services officer (name) ('s signature2) Z.v. 2 notes. 1 entries are made by customs officials if the fertilizer is imported from third countries. 2 document property "signature" and "Z.v." does not fill in, if the electronic document is drawn up according to the law on electronic document design. Agriculture Minister John Dūklav 16. attachment Cabinet 1 September 2015 regulations no 506 application authorization ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ (indicate the name of the permission).     .                             day month year i. General information 1. applications for authorisation shall be submitted (the desired mark with x) manufacturer importer Packager draftsman of the mixture 2. Applicant's registration number in the register of the competent institution 3. Applicant: 3.1 3.2 name registered office 3.3. phone number fax number e-mail address 4. details of person submitting application: 4.1-4.2. ID code name surname 4.4 4.3 identity documents in the data (filling out If no ID code): the name of the issuing authority 4.4.1 4.4.2 4.4.3. number. date of issue 5. Fertilisers or substrate manufacturer: 5.1 5.2 5.3 the name address telephone number fax number e-mail address 5.4. manufacturer's registration number in the register of the competent institution (II). information on fertilizer or substrate 6. Fertilizer or substrate type 7. Name: 7.1 the official name (if any) 7.2. trade name (if any) 8. production metode1 9. Izejvielas1 10. Indication of lietošanu1 11. Fertilizer or substrāta2 : 11.1. total mass (the liquid – can be a volume) 11.2. one packaging mass (the liquid – can be a volume) packaged fertilizers and substrates 11.3. number of packages 11.4. lot number I certify that the information provided is correct (the registration applicant's first name, last name and paraksts3) notes. 1 unregistered fertilizers. 2 fill out only those permissions that require it. 3 document property "signature" does not fill in, if an electronic document is drawn up according to the law on electronic document design. Minister of agriculture John Dūklav