Regulation Concerning Vocational Training For The Print Media Technologists And The Print Media Technologist

Original Language Title: Verordnung über die Berufsausbildung zum Medientechnologen Druck und zur Medientechnologin Druck

Subscribe to a Global-Regulation Premium Membership Today!

Key Benefits:

Subscribe Now for only USD$20 per month, or Get a Day Pass for only USD$4.99.

Regulation on vocational training for media technologists printing and media technology printing (printer training ordinance-printer excernment)

unofficial table of contents

printer excercture

date of delivery: 07.04.2011

Full quote:

" Pressure-Training Ordinance of 7. April 2011 (BGBl. I p. 570) "

*)
This regulation is a training order within the meaning of Section 4 of the Vocational Training Act and § 25 of the Craft Code. The training regulations and the coordinated framework curriculum for vocational schools, agreed by the Standing Conference of the Ministers of Education and Cultural Affairs of the Länder in the Federal Republic of Germany, will shortly be published as a supplement to the Federal Gazette published.

Footnote

(+ + + Text evidence from: 1.8.2011 + + +)

unofficial table of contents

input formula

The reason for § 4 (1) in conjunction with § 5 of the Vocational Training Act, of which § 4 (1) is replaced by Article 232 (1) of the Regulation of 31 December 2008. October 2006 (BGBl. 2407), as well as the first sentence of Article 25 (1) of the Craft Regulations, which was last amended by Article 146 of the Regulation of 31 December 2008. October 2006 (BGBl. 2407), 23. March 2005 (BGBl. 931), the Federal Ministry of Economics and Technology, in agreement with the Federal Ministry of Education and Research, is responsible for: unofficial table of contents

§ 1 State recognition of the vocational training profession

The training profession media technologist printing and media technology printing becomes
1.
according to § 4 paragraph 1 of the Vocational Training Act and
2.
according to § 25 of the Craft Regulations for the training for commercial number 40 "Bookprinter: typesetter; printer" of Appendix B 1 of the craft order
governmental/handcraft/handcrafting

Footnote

§ 1 No. 2 italic print: must be correct "Appendix B section 1" unofficial table of contents

§ 2 Duration of the Vocational training

The training lasts three years. Non-official table of contents

§ 3 Structure of vocational education and training

Vocational training is divided into
1.
Compulsory qualifications according to § 4, paragraph 2, section A and C,
2.
two in the training contract to be determined Optional qualifications in accordance with § 4 (2) (B) (1) and
3.
qualification to be determined in the training contract in accordance with § 4 (2) (B) (b) (b) (1) 2.
Non-official table of contents

§ 4 Training framework plan, training professional image

(1) The subject of vocational training shall be at least the subject of the Training framework (Appendix) skills, knowledge and skills (professional capacity to act). An organization of the training which deviates from the training framework plan is particularly permissible, insofar as special operational features require the deviation.(2) Vocational training for media technologists printing and media technology printing is broken down as follows (training professional image):

Section A
Vocational training skills, knowledge and skills in the compulsory qualifications according to § 3, number 1:
1.
Schedule the flow of print jobs,
2.
Setting Up Printing Machines,
3.
Printing Print Processes,
4.
Printing technologies and processes,
5.
Printing Printing Machines;
Section B
More professional-profile skills, knowledge and skills from the selection lists I and II:
1.
two Optional qualifications according to § 3 (2) of the shortlist I:
I.1
Data preparation Digital Printing,
I.2
Print Forming Art Print Method,
I.3
printing form,
I.4
printing and planning printing, newspaper printing,
I.5
Gravure Printing,
I.6
Gravure Printing,
I.7
Print Forming Artistic Printing,
I.8
Command-based process control, Sheetfed offset printing,
I.9
State-of-the-line process control, web offset printing,
I.10
Command-based process control, gravure,
I.11
digital printing process,
I.12
mailing-production,
I.13
print finishing,
I.14
Inlineveredelung,
I.15
InlineProduction,
I.16
print reprocessing,
I.17
product editing,
I.18
Machine technology and advanced maintenance, web offset printing,
I.19
Machine technology and advanced Maintenance, Illustrationstiefdruck,
I.20
Machine technology and advanced maintenance, rotary flexo, wallpaper, decor deep, packaging deep-and Label printing,
I.21
Other printing process engineering;
2.
an Election Qualification according to § 3, number 3, list II:
II.1
sheetfed offset printing,
II.2
Akzidenz Web Offset Printing,
II.3
Newspaper Printing,
II.4
Formulardruck,
II.5
Illustrationstiefdruck,
II.6
TapePrint,
II.7
Decemp Print,
II.8
Packaging Print,
II.9
Labels-Roll Print,
II.10
flexo printing,
II.11
digital printing,
II.12
Large-format digital print,
II.13
Artistic Printing;
C
Integrative skills, knowledge and skills in the compulsory qualifications according to § 3 Number 1:
1.
VET, labor and collective bargaining,
2.
Construction and organization of the Training operations,
3.
Safety and health at work,
4.
Environment,
5.
Operational communication.
unofficial table of contents

§ 5 Implementation of vocational training

(1) The skills, knowledge and skills referred to in this regulation should be taught in such a way as to ensure that the To be qualified for the exercise of a qualified professional activity within the meaning of Article 1 (3) of the Vocational Training Act, which includes, in particular, independent planning, carrying out and controlling. The qualification described in sentence 1 shall also be proven in the tests in accordance with § § 6 and 7.(2) On the basis of the training framework plan, the trainees have to draw up a training plan for the trainees.(3) The apprentices must have a written proof of training. They should be given the opportunity to carry out the written evidence of formal qualifications during the training period. The trainees have to check the written proof of training on a regular basis. Non-official table of contents

§ 6 Intermediate examination

(1) An intermediate examination is to be carried out in order to determine the level of training. It is to take place before the end of the second year of training.(2) The intermediate examination shall cover the skills, knowledge and skills listed in the Annex for the first three years of training, and the teaching material to be provided in the course of vocational education, to the extent that he/she is responsible for: Vocational training is essential.(3) The intermediate check is found in the examination areas
1.
Work Planning and
2.
printing technology
instead.(4) For the Work Planning Examination Area, there are the following specifications:
1.
The test piece should demonstrate that it is capable of
a)
Planning work steps, setting work equipment, selecting materials, requirements of work, health and environmental protection as well as cost-effectiveness
b)
Take over and review print data or printing forms, and implement given product and process data in the planning process,
c)
Planning the printing and control processes of printing machines, thereby interacting with materials, printing inks, printing materials and printing presses in the printing process
d)
perform print-specific calculations;
2.
Check-ing is intended to process practical tasks in writing;
3.
the exam time is 120 minutes.
(5) For the examination area printing technology the following are: Preferences:
1.
The test object is to demonstrate that it is capable of
a)
Printing Machines to set up the print result, taking into account printing inks, printing materials and machine settings, and to start the printing process,
b)
To perform printing process checks during printing; measure, check and document parameters, print process and print result to optimizing;
2.
The test piece is to produce a test piece and document its work with practice-based documents;
3.
the exam time is four hours.
unofficial table of contents

§ 7 Final examination, journeyman's examination

(1) The final examination or journeyman's examination shall determine whether the examinee has acquired the professional capacity to act. In the final examination and the examination of a journeyman's examination, the examiner is to prove that he has the necessary professional skills and skills and has the necessary professional knowledge and skills and is required to teach in the course of the vocational education and training course. is familiar with essential training materials for vocational training.(2) The final examination or journeyman's examination shall cover the skills, knowledge and skills listed in the Annex, as well as the teaching material to be mediated in the course of vocational education, insofar as it is essential for vocational training. The training regulations should be based on.(3) The completion or journeyman check consists of the examination areas:
1.
Print Production,
2.
Work Order Planning and Communications,
3.
Process Technology,
4.
Economic and social studies.
(4) For the print production examination area, the following specifications are specified:
1.
The test piece is to demonstrate that it is able to
a)
presses with respect to their To adjust the basic setting and to take into account machine-related relationships in function checks,
b)
the requirements for work orders and To obtain materials for setting up printing machines and to start print jobs,
c)
Review and assess print results visually and metrologically, Intervention in the production process to take into account the interconnections within printing presses as well as with regard to the print result to be achieved and to include them in its actions,
d)
To produce print jobs in the specified quality on time,
e)
its work with documenting practical documents;
2.
The examinee is to have a work assignment as well as a situational dialogue according to the one in the training contract , in accordance with Article 4 (2) (B) (2), one of the optional qualifications laid down in the training contract must be taken into account in accordance with Article 4 (2) (B) (1);
3.
The exam time is seven hours, within this time the situational discussion will last for a maximum of ten minutes.
(5) For the examination area Order planning and Communication has the following specifications:
1.
The test object is to demonstrate that it is capable of
a)
Planning and documenting work processes in accordance with economic, technical, organizational and personal requirements,
b)
Planning work steps including information from upstream and downstream production areas,
c)
To evaluate machine data, gather and back up order documentation,
d)
The properties of materials, printing inks and substrates as well as their interactions with each other and with the presses used,
e)
performing planning-relevant calculations;
2.
the test item is to perform practice-related tasks Editing in writing;
3.
the exam time is 120 minutes.
(6) For the process technology review area, the following preferences exist:
1.
The test object is to prove that it is able to
a)
Printing processes with regard to their
b)
Process-specific parameters as well as production conditions in relation to printing machines, Materials, printing materials, printing inks including colour mixing systems, drying, operating conditions and production specifications to be taken into account and used,
c)
To apply quality assurance measures for the optimization of print results; to use process-related measuring and control elements,
d)
taking advantage of the techniques used in the techniques used,
e)
Requirements to take into account print processing,
f)
Functions of machine elements as well as measures for the maintenance of machines and equipment assess,
g)
perform process-related calculations;
2.
the test item The aim is to write practical tasks in writing;
3.
the exam time is 120 minutes.
(7) For the examination area, economic and social studies exist. the following guidelines:
1.
The examinee is to prove that he is capable of general economic and social relations of the working and working world To represent and evaluate;
2.
The test object is to process practice-oriented tasks in writing;
3.
the exam time is 60 minutes.
unofficial table of contents

§ 8 Weight and Bestee Control

(1) The individual examination areas must be weighted as follows:

1. Print Production Audit Area
50 Percent,
2. Order Planning Examination Area
and Communications
20 Percent,
3. Examination area process technology
20 percent,
4. Examination area
economic and social studies
10 percent.
(2) The completion or Pass validation passed if the performance
1.
in the overall result with at least "sufficient",
2.
at least "sufficient" in the print production area,
3.
in the print production area. At least two other examination areas with at least "sufficient" and
4.
have not been rated "insufficient"
any examination
.(3) At the request of the examinee, the examination in one of the examination areas "order planning and communication" or "process technology" or "economic and social studies" assessed as "sufficiently" is evaluated by an oral examination of approximately 15 minutes, if this can be the result of the passing of the test. In determining the result for this examination area, the previous result and the result of the oral supplementary examination in the ratio of 2: 1 are to be weighted. Non-official table of contents

§ 9 Additional qualification

(1) A non-selected qualification in the course of vocational training in accordance with § 4 (2) Section B, paragraph 2, may be provided as an additional qualification.(2) In order to provide the additional qualification, the objective structure contained in Annex B, point 2 shall apply accordingly. Non-official table of contents

§ 10 Examination of the additional qualification

(1) The additional qualification will be completed within the framework of the final examination or the journeyman's examination shall be examined separately if the skills, knowledge and skills contained in Annex B, point 2, have been mediated accordingly.(2) § 7 (4) shall apply for the examination of the additional qualification.(3) The examination of the respective additional qualification has been passed if the examinee has provided at least sufficient services.(4) A separate certificate shall be issued on the result of the successful examination of the additional qualification. Unofficial Table Of Contents

§ 11 Existing Vocational Training Conditions

Vocational training conditions which, at the date of entry into force of this Regulation if an intermediate examination has not yet been filed and the contracting parties agree to do so, the provisions of this Regulation shall continue to take into account the training period previously completed. Unofficial table of contents

§ 12 Repeal of the recognition of training occupations

The recognition of the training profession of the Steindrucker and the Stone printer for the craft sector is repealed. Non-official table of contents

§ 13 Entry into force, expiry

This regulation occurs on the 1. August 2011 in force. At the same time, the regulation on vocational training becomes the printer/printer of 2. May 2000 (BGBl. 654). Non-official table of contents

Asset (to § 4, paragraph 1, sentence 1)
Training framework for vocational education and training for media technologists printing and Media technology in print

(Fundstelle: BGBl. I 2011, 574-589)

Section A: Professional skills, knowledge and skills in the compulsory qualifications in accordance with § 3 Number 1 Lfd.
No.Part of the
Training profession image-to-training
skills, knowledge, and skill-time-values
in weeks in1. until 18.
Month 19. up to 36.
month1234
1 Schedule the expiration
of print jobs
(§ 4 paragraph 2
section A number 1)
a)
Order documents for completeness check and feasibility of production specifications control
b)
Check print data or print forms for completeness and usability
c)
Shooting pages, page and user arrangement, taking into account print finishing preferences, as well as control elements for printing and print finishing verifying
d)
Planning and setting machine usage
e)
Materials for production select, select, and check for usability
f)
Production conditions, in particular with respect to the interactions of the printing machine, the printing material, the printing ink and climate, assess
g)
Product and process data in the planning of orders, especially taking into account color management, color systems, color technology, Drying, curing and finishing, use
h)
Technical processes as an integrated production process, taking economic and ecological aspects into account
i)
Store material and use intra-operational logistic processes
22
2 Set up
printing machines
(§ 4 paragraph 2
Section A number 2)
a)
Properties of (b)b) style="font-weight:normal; font-style:normal; text-decoration:none;"> Properties of printing inks, in particular consistency, viscosity, color locus, drying behavior, fastness properties and abrasion resistance, assess
c)
Apply job data for press control, set up and drive the press in a product-oriented way
d)
Review print quality, in particular print colors, register and register
e)
Target-is-comparison between print results and customer requirements, and optimize machine settings
f)
after the optimized print result has been matched to the Document customer requirements and after print release record data and start
28
3 Taxation of
printing processes
(§ 4 paragraph 2
Section A number 3)
a)
run print process control running, with errors in the process flow, the print result, and Detecting and fixing problems in the machine run-off
b)
Visual and metrological testing, selecting measurement parameters, applying measurement technology, measurement results Evaluate the comparison between the print results and the set specifications, derive measures to correct the reproduction result
c)
Impact-related of the control and the control. Control processes as well as sensors and mechanical, pneumatic, hydraulic, electrical, electronic and electropneumatic functions in printing machines and auxiliary units
d)
Changing the printing press, process-specific print media, printing ink, and printing stock when changing individual settings
e)
Log Manufacturing
28
4 Printing technologies
and processes
(§ 4 paragraph 2
section A number 4)
a)
Manufacturing process with respect to the quality of the product to be achieved Assessing printed products including cost and resource conservation
b)
Printing Machines, especially with regard to function, design, control and control, as well as
c)
Material behavior with respect to the manufacturing process and the required quality. assess
d)
divide printing materials by category of printing material and, taking into account the printing and pressure processing processes, the storage conditions and the Assessing the use of the end product
e)
Printing inks differ according to product requirements and with regard to processability in the entire production process as well as the use of the final product.
f)
assess the color effect of the interplay with the printing material and the lighting
g)
Applying color spaces and color systems, respecting standards and
10
5 Maintenance of printing machines
(§ 4 paragraph 2
section A number 5)
a)
The interaction of different machine elements and assemblies to the overall function Check
b)
Functions of printing machine parts in compliance with safety specifications, in particular sensors, mechanical, pneumatic, hydraulic, electrical, electronic and electropneumatic machine elements, check
c)
detect and describe faults in machines and devices, eliminate errors, and rectify Prompt
d)
Check the basic settings of the press, adjust the machine according to preferences
e)
Perform maintenance, replace wear parts
10





f)
Security check for their effectiveness
g)
Document changes to machine settings and replacement of machine parts and test
B: Further professional-profile skills, knowledge and skills from the Elective qualification1. Selection list I (electoral qualifications according to § 3 point 2) Lfd.
Nr.Part of the

skills, knowledge, and skill-time guidance values
in weeks in1. until 18.
Month 19. up to 36.
month1234
I.1 Data Preparation
Digital Printing
(§ 4 Paragraph 2
Section B
Number I.1)
a)
Data on completeness and usability, in particular on compliance with print technology Basic parameters, check
b)
Prepare data for print-compliant output, and place it in format and use, split motif for multi-part printed sheets, and Integrate system-specific further processing and control elements
c)
Create printer output files
d)
Create and verify audit patterns
e)
Save and archive production
13
I.2 Print Form Preparation Artistic Printing Process
(§ 4 Paragraph 2
Section B
number I.2)
a)
Traditional forms of pre-printing process-specific distinguish
b)
Materials and Select tools for pre-print preparation
c)
Prepare printing forms manually and machine for image capture
d)
Check printing forms for use in the special traditional printing
13
I.3 Print Form Manufacturing
(§ 4 paragraph 2
Section B
number I.3)
a)
Set work flows, Planning work items and verifying data for completeness and technical feasibility
b)
Subdivisions for printing forms, taking into account the production conditions create
c)
arrange pages or benefits, position correctly, and check them on register
d)
Build printing forms from digital data sets, integrate measurement and control elements, consider standardization systems
e)
insert exposure curves and consider print characteristics
f)
Create formproof and verifying
g)
Printing, visually and metrologically testing printing
13
I.4 Print form manufacturing and planning,
newspaper printing
(§ 4 paragraph 2
section B
number I.4)
a)
Planning for machine resources, ensuring collaboration with upstream and downstream departments
b)
Create print for production requests and derive preferences for printing formwork
c)
Summarize production documents and provide them to set up the machines
d)
master data creating and maintaining
e)
Apply and verify data, distinguish grid types, and use for printing form
f)
insert exposure curves and consider print characteristics
g)
create printing forms, visually and Test metrology
13
I.5 Gravure Printing
(§ 4 paragraph 2
Section B
number I.5)
a)
Select print-form editing options
b)
Compare print template with print result, detect deviations, draw corrections on printed sheets
c)
Run Plus and Minus corrections, assess print result after correction
d)
cylindrical polishes
13
I.6 Gravure Printing
(§ 4 Paragraph 2
Section B
number I.6)
a)
Control cylinder properties
b)
Set cylinder circumferenda and gradation
c)
Create engraving log and folder schema
d)
Gradation creation options Check
e)
mount scan templates and set scan heads
f)
lift the print cylinder and prepare engraving systems
g)
Control engraved cylinders and prepare them for
13
I.7 Print Form Manufacturing Artistic Printing
(§ 4 Paragraph 2
Section B
Number I.7)
a)
Reproductions or originals with respect to their use for print rendering in an artistic printing process
b)
Select and use tools and materials for the creation and transfer of the print image
c)
Print forms process-specific for traditional printing
d)
Print image on Check and assess the usability of the traditional printing process
e)
Printing forms for multicolor prints, in particular with respect to Passer and original color reproduction,
f)
Create print and post-edit print image if
13
I.8 Command-based
process control,
sheetfed offset printing
(§ 4 paragraph 2
Section B
number I.8)
a)
Product planning and control systems as well as networks in connection with the press
b)
maintain and adjust control and control facilities
c)
Select control characteristics and adjust to changed production conditions
13
d)
Control processes, if necessary manually correct product-specific
e)
peripherals, in particular air supply and dampening solution, control, set and wait
I.9 Command-based
process control,
web offset printing
(§ 4 paragraph 2
section B
Number I.9)
a)
Analyzing the control structure and showing capabilities
b)
Production planning and Control systems and networks used in connection with the press
c)
Mainland and adjust control and control equipment
d)
Ensure function of process monitoring systems and control devices
e)
Rail voltage systems setting
f)
Setting the longitudinal, page, main, and side registers
g)
Wendesysteme
13
I.10 Control-level
Process control,
low-pressure
(§ 4 paragraph 2
section B
number I.10)
a)
Perform adjustment and monitor printing process
b)
Monitoring the measurement and control function, correct if necessary
c)
Production monitoring systems
d)
Determine production data and log
13
I.11 Digital printing process
(§ 4 paragraph 2
Section B
number I.11)
a)
Select and prepare a printing machine
b)
Check the printable for suitability, specific Set parameters
c)
Check print data for completeness and usability
d)
checking sample print visually and metrologically for compliance with the preferences
e)
Running system-specific maintenance and cleaning
  13
I.12 Mailing Production
(§ 4 paragraph 2
Section B
number I.12)
a)
Check individual data for completeness, with data protection law Note provisions
b)
Prepare individual data in compliance with the printer output preferences
c)
checking layout data for compliance with the shipping service provider's terms
d)
ready to print production release
e)
Prepare production processes and production
f)
Process and pack mailings according to preferences
g)
documenting production processes and production data in compliance with data protection requirements, and archiving
13
I.13 Print refinement
(§ 4 paragraph 2
Section B
number I.13)
a)
Check printed products and prinfabrics for finishing
b)
Process and product-specific Applying the finishing techniques
c)
Use protection and effect lacquers in a process-specific and production-specific way
d)
Properties of lacquers, especially viscosity, check
e)
Control of print results, causes for Detect and eliminate deviations
f)
Review the finished printed product, especially on drying, gloss, block and abrasion resistance
g)
documenting the finishing process
13
I.14 Inlineveredelung
(§ 4 paragraph 2
Section B
number I.14)
a)
refining materials, taking into account their properties, Select and use processing options, quality, economy and environmental protection
b)
Apply finishing techniques and their particularities, In particular effect and function lacquers, hot and cold foil embossing, film laminations and laminations, consider
c)
Inlineveredelungswerkzeuge und -Remove and remove, adjust, maintain, and store stations
d)
detect and eliminate faults in processing stations
e)
Perform the quality checks in the process and optimize the interaction of printing, finishing, and processing
f)
assessing the usability and quality of the finished end
13
I.15 InlineProduction
(§ 4 paragraph 2
Section B
number I.15)
a)
Schedule machine usage product-related
b)
Distinguish and select auxiliary units in the functional structure, integrate into the process chain, set and ensure interaction with the press
c)
Eliminate Failures in Aggregates
d)
Wait for Aggregates and
13
I.16 Print further processing
(§ 4 Paragraph 2
Section B
number I.16)
a)
Set process paths for print products processing
b)
print products with Process different print finishing techniques to the end product
c)
Select and use product-specific materials
d)
equip devices for print reprocessing after job description has been specified
e)
Monitor and optimize machine running, detect and fix flow-related failures
f)
Review and assess work products, perform quality control according to customer preferences and quality standards
g)
Store material-and transport-
13
I.17 Product processing
(§ 4 paragraph 2
Section B
number I.17)
a)
Process paths and work steps order-specific for assembly, in particular for cutting, punching, scoring, grooving, cutting, deep drawing, sawing, milling, lasing, cutting plotting, laminating, laminating, eyelet, flanging, lining and sewing, setting
b)
Select and deploy materials, machines, and work equipment
c)
Print products
d)
Review and assess work products, quality control according to customer preferences, and Performing quality standards
e)
Store product and transport rights
f)
Maintaining and maintaining machines, devices, and tools of
13
I.18 Machine technology
and advanced
maintenance,
web offset printing
(§ 4 paragraph 2
section B
number I.18)
a)
Check the functions of power transmission and drive elements, detect faults and their causes, and fix them
b)
Select lubricants by use and use them in compliance with lubrication plans
c)
Switch and adjust circular knives and tumors, insert and remove arrester groups, adjust points, blade and blade bars, check folding blades for wear, Clean the pre-folding and circumferential adjustment and check for functionality
d)
Drag and drop transport and deceleration tapes
e)
Control the preload using the print strip
f)
adjust the color meter
g)
Switch and adjust the inking and dampening rolls
h)
Maintenance work on auxiliary units or Drier systems
13
I.19 Machine technology
and advanced
maintenance,
illustration gravure printing
(§ 4 paragraph 2
Section B
number I.19)
a)
Check the functions of power transmission and drive elements, Set gears, detect malfunctions and their causes and cause repair
b)
Select lubricants by use and with respect for grease plans deploy
c)
Switch and adjust inking rollers
d)
Setting the press release Check the print strip, change the press, and set
e)
Control and adjust sandwich groups and draw rolls
f)
Check and renew the collection cylinder for completeness and condition, change the stitching blade
g)
Replacing the gripper, cutting knife, and folding blade
h)
Transport and deceleration tapes, and set, train and friction wheels
13
I.20 Machine technology
and advanced
maintenance,
rotary flexo, wallpaper, decor deep, packaging deep and label printing
(§ 4 paragraph 2
Section B
number I.20)
a)
Functions of Check the power transmission and drive elements, detect faults and their causes, and cause
b)
Select lubricants by use and
c)
dismantle, clean, assemble, deploy and set the doctor blade systems
d)
Control, clean, and set color-transfer, color-cleaning-and color-supply systems
e)
Control, cleanse and calibrate viscosity control and viscosity control systems
f)
Perform Maintenance Work on Additional Aggregates and Dry Systems
g)
Railway guidance and Controlling, maintaining and adjusting the web-tension
13
I.21 Other Printing Process Engineering
(§ 4 Paragraph 2
Section B
number I.21)
Applying a further printing process technology in the areas of offset printing, high-pressure, gravure printing, digital printing or Screen printing. The following qualifications are to be given:
a)
Analyze the task in a process-specific way. and possible solutions on the basis of operational conditions
b)
Planning order execution and printing process taking into account machine technology Preparing conditions
c)
Materials taking into account their properties, processing capabilities, costs, quality and environmental protection select and use
d)
Prepare the print job or printing form system-specific, adjust the pressure in a stand-up manner, andrut as well as by default and on the basis of Adjust the print control elements, correct settings for deviations
e)
Set up the press production-related
f)
Set up multi-color printed matter, dock and match the template, control and monitor current production
g)
Print result, especially on sound and color value, and Passer, check
13
2. Selection list II (optional qualification according to § 3 point 3)Lfd.
Nr.Part of the

skills, knowledge, and skill-time guidance values
in weeks in1. until 18.
Month 19. up to 36th
month1234
II.1 sheetfed offset printing
(§ 4 paragraph 2
Section B
Number II.1)
a)
Set sheetfed offset presses on different types of printing
b)
Select printing blankets, Checking and setting the print
c)
Color order in multi-color printing by determining requirements and standards for printing
d)
Basic setting of inking and dampening system, settings for print job optimize
e)
Check and adjust dampening solution with additives in terms of production and machinery, in particular conductivity, pH, hardness, and concentration of the Additive, review and assess
f)
visually and metrologically assess printing plates for their suitability for the required print quality
g)
visually and metrologically check and evaluate print control elements, make corrections for deviations
h)
Check the print results, determine print characteristics, process standards, and standardization specifications for sheetfed offset printing
i)
Discertify errors in the print result and failures in the machine flow as well as in the sheet guidance, and eliminate causes
j)
Monitor and optimize machine running, ensure trouble-free running of the press
26

II.2 Akzidenz web offset printing
(§ 4 paragraph 2
Section B
number II.2)
a)
Set up the format and thickness of the roll changer
b)
Basic color and dampening system settings perform, optimize settings for print job, select printing blankets, check and adjust print processing
c)
dampening solution with additives production and machine-related testing and adjustment, in particular conductivity, pH value, hardness and concentration of additives, check and assess
d)
dryer temperature below Adjusting the printing stock and energy efficiency
e)
Setting rehumidification systems
f)
Basic settings of circular knives, strand registers, and turner bars or folders
g)
Place the web after production request and set the web guide elements
h)
Folkfolder set up for production, install and set the folding equipment and auxiliary units
i)
Set up and transfer systems for further processing
j)
Check the print result's color and tone values, determine the print characteristic of the press, process standards, and standardization constraints for web offset printing
k)
Monitor and optimize machine running, ensure trouble-free running of the
26
II.3 Newspaper Print
(§ 4 Paragraph 2
Section B
Number II.3)
a)
Preparing the roll changer and setting it up to print width
b)
Select printing blankets, print handling Check
c)
Check and adjust dampening solution with additives in terms of production and machinery, in particular conductivity, pH, hardness and concentration of additives, Check and assess
d)
Adjust Hopper and Ancestor Spindles, Main and secondary registers for production, convert and adjust turning bars, and circular knives and Adjust
e)
Configure the press by requirements
f)
Train move to Perform production requisition and set web guiding elements
g)
Folk folder and folding equipment as well as transfer system for further processing for production setting up requirements of dispatch room technology
h)
Press line supports starting as well as track, stand, passer and printing ink optimize
i)
Perform colored multi-book production
j)
Monitor machine run and optimize, ensure trouble-free running of the
26
II.4 Formulardruck
(§ 4 paragraph 2
Section B
number II.4)
a)
Preparing the paper roll on the roll carrier for printing, setting tension elements on production conditions, Set and control web lengths according to preferences
b)
Select printing blankets, check print processing, and set
c)
Basic color and dampening system setting, optimize print job settings
d)
determining the color order for multi-color printing according to printing requirements and standardization preferences
e)
Check and adjust dampening solution with additives in terms of production and machinery, in particular conductivity, pH, hardness and concentration of additives, and
f)
Set up individual and ancillary equipment as well as additional equipment in the form-printing machine, in particular punching and perforating devices, operate and maintain
g)
visually and metrologically assess printing forms in terms of their suitability for the required print quality
h)
Check the print result's color and tone values, determine the print characteristic of the press, process standards, and standardization preferences for the form printing
i)
Monitor and optimize machine running, ensure trouble-free running of the
26
II.5 Illustrationstiefdruck
(§ 4 Paragraph 2
Section B
Number II.5)
a)
Basic settings of the squeegee device
b)
Basic settings of circular knives, strand registers as well as turning bars or folders
c)
Preparing the roll changer and setting it up to print width
d)
adjust folding flaps and gripper systems to product thickness, change cutting rubber strip, set paddle wheels, washers, delivery and feed of products
e)
Set web tension systems
f)
Install cylinders, extractor hoods, and security devices, Monitor exhaust air purification systems
g)
Control and adjust coloration systems, color controls and viscosity controls on print jobs vote
h)
Set press systems to format
i)
From and transfer systems to the further processing set up
j)
Press line supports ascend as well as optimize the web, register, register, and print ink, steam and Setting drying equipment
k)
Electrostatic charging of the paper web in the printing unit, paper strand adhesion and silicone applicator deploy
l)
Monitor and optimize machine running, ensure trouble-free running of the
26
II.6 Tapet Print
(§ 4 Paragraph 2
Section B
Number II.6)
a)
Preparing the reelchanger and rewinding and setting it up to print width
b)
merge color after Set the template and tune it to the template
c)
equip the press, set it to format, and prepare printing units for printing
d)
Influenceable, in particular color, properties of the printing materials, state of the printing form and printing speed, check and reposition of a wallpaper pattern Use
e)
Set the squeegee device to change the expression
f)
measuring and Set the test equipment and use it for production control
g)
Expression of the wallpaper pattern, in particular due to technical parameters of the press, selection of the Printing form and change of color viscosity, set
h)
Set register
i)
Create and assess the samples of the end products, make corrections in case of deviations in the quality of the printed product
j)
monitor and optimize machine running, ensure trouble-free running of the press
k)
Archive machine parameters and order data for repeat
26
II.7 Decorative Gravure
(§ 4 paragraph 2
Section B
number II.7)
a)
Preparing and rewinding a roll changer and rewinding Set the print width
b)
Set the mixed color by template and tune it to the template
c)
equipping the printing machine, setting it to format, and preparing printing units for printing
d)
influencing variables, In particular, the colour, the quality of the printing materials, the service life of the printing cylinders and the printing speed, and the use of a décor
e)
Set the squeegee device to change the expression
f)
Set measurement and testing facilities and for the Production control use
g)
Expression of the decoration, in particular by technical parameters of the printing press and change in the color viscosity, set
h)
Set tab
i)
Create and assess patterns of end products
j)
Monitoring and optimizing machine running, trouble-free running of the printing press Ensure
k)
Archive machine parameters and job data for repeat
26
II.8 Packaging print
(§ 4 paragraph 2
Section B
number II.8)
a)
Order documents after Check product and further processing specific requirements and enter order data for machine control
b)
Packaging-specific printable materials, Selecting, preparing and deploying printing inks and varnishes
c)
mixing special colors
d)
Setting up a packaging printing machine, setting the printing machine parameters in a process-oriented way, and taking into account printing process-specific conditions
e)
Setting up and serving additional units within the packaging printing machine
f)
The packaging printing machine is going on, while material on, register, register, print color and finishing are coordinated and optimized
g)
maintaining and adjusting control and control equipment
h)
print result on Evaluate processing capability, usability and quality, coordinate with templates and optimize according to quality requirements
i)
Quality controls after Perform and evaluate standards and specifications, apply packaging-specific test methods
j)
Monitor and optimize machine running, trouble-free running of the Ensure packaging printing
26
II.9 Label roll press
(§ 4 paragraph 2
Section B
number II.9)
a)
Order of the printing process depending on the print product's requirements set
b)
Select, prepare and deploy printing materials, finishing materials, printing inks, varnishes, and adhesives
c)
special colors mixing
d)
Set up additional aggregates within the label printing machine, and
e)
Set drying systems on printable materials and printing inks, while respecting energy efficiency
f)
Use punching devices, set up and operate as well as check the punching result
g)
printing units
h)
Apply process and product-specific finishing techniques
i)
Set up label-specific cutting systems
j)
Printing machine parameters process-oriented set
k)
A label printing machine, including material on, register, register, printing ink, grid removal, cutting systems and finishing, as well as optimize
l)
Multi-color labels on specific substrates inline
m)
assess the print result for usability and quality, coordinate with the templates and optimize them according to the quality requirements
n)
Perform and evaluate quality controls according to standards and specifications, apply a label-specific test method
o)
after print release label printing machine run up to print speed and monitor reprint
p)
Checking labels for workability
q)
Printed label rolls material-and transport-friendly
26
II.10 Flexo print
(§ 4 paragraph 2
Section B
number II.10)
a)
Order documents after Checking product and further processing specific requirements and entering order data for machine control
b)
Set inking unit usage and grid rolls Select and use
c)
install printing forms on a format cylinder
d)
Select, prepare and deploy printing inks, printing inks, and auxiliary materials, mix printing inks
e)
Setting roll winding devices on printable materials
f)
mechanical drive devices Mounting the format cylinders and anilox rollers
g)
Setting up a flexographic printing machine, including additional units, with special features and product specific features
h)
Set process-oriented printing machine parameters
i)
Flexographic printing machine, in particular material on, print job, register, register and printing inks, coordinate and optimize each other
j)
Set drying systems to print substrates and printing inks, consider energy efficiency
k)
Print results for workability, usability and quality, coordinate with templates and optimize according to quality requirements and document
l)
Perform quality checks according to standards and specifications, apply flexo-pressure-specific test methods
m)
Monitor and optimize machine running, ensure trouble-free running of the flexo printing machine
n)
Archive machine parameters, order data, and print forms for repeat orders
o)
Print products Store material and transport

26
II.11 Digital Printing
(§ 4 Paragraph 2
Section B
Number II.11)
a)
Print production, in particular with respect to deadlines and record order, optimized planning
b)
Link layout data with databases
c)
Printing systems order-related selecting and preparing
d)
Check the printing stock for suitability, set the printing system to specific properties of the printing stock
e)
Test sample printing visually and metrologically for compliance with the preferences
f)
Inline processing systems set up order-related
g)
Multi-sets in compliance with the other Determine the process steps
h)
prepare prints, visually and metrologically check the print process for compliance with the preferences
i)
Running system-specific maintenance and cleaning
  26
II.12 Large-format
digital print
(§ 4 paragraph 2
Section B
number II.12)
a)
Process paths and work items order specific to the Set large-format digital printing
b)
Create print profiles for different print materials
c)
Setting and calibrating printing systems on selected printing stock
d)
Create digital prints, Check and optimize
e)
Monitoring machine running and drying as well as checking color adhesion and resistances during print quality and templates
e)
and optimize
f)
Run system-specific maintenance and cleaning
g)
Securing and archiving production data
h)
Printing products material and transport
26
II.13 Artistic
printing techniques
(§ 4 paragraph 2
Section B
number II.13)
a)
Set work items, consider copyrights and related rights, and privacy
b)
Preparing printing forms for serial printing
c)
Materials for editing, modification, and correction Use the printing forms
d)
Prepare and produce printing inks
e)
Printing Machines and print devices
f)
Create a print, assess print results for multi-color prints, and coordinate with the customer
g)
with artists expressions experimentally worked out
h)
Interaction of printing machine, printing ink and printing stock for the faithful reproduction of the print result
i)
Create a print manually or by machine
j)
post-edit and archive printing forms
k)
document print
26
C: Integrative skills, knowledge and skills in the compulsory qualifications according to § 3 Number 1Lfd.
No.Part of the
Training profession image to be mediated
Skills, knowledge, and capability time guide values
in weeks in1. until 18.
Month 19. up to 36.
month1234
1 Vocational Training,
Work and Tariffy
(§ 4 Paragraph 2
Section C
Number 1)
a)
The importance of the training contract, in particular completion, duration, and termination, declaring
b)
cite mutual rights and obligations under the training contract
c)
Possibilities of continuing vocational training
d)
essential parts of the employment contract
e)
Essential provisions of the collective agreements applicable to the establishment of the
 
2 Construction and
Organization of
training company
(§ 4 paragraph 2
Section C
number 2)
a)
Exacting the structure and tasks of the forming enterprise
b)
explaining the basic functions of the forming enterprise such as procurement, manufacturing, sales and administration
c)
The relationships of the training company and its employees to economic organizations, professional representatives and trade unions call
d)
Basics, tasks and working methods of the company's constitutional or personnel representative bodies describe
3 Security and
Health protection
at work
(§ 4 paragraph 2
Section C
number 3)
a)
detect threats to health and safety at work and measures to avoid them
b)
Apply occupational health and accident prevention
during
total
training time
to mediate
c)
Describe accidents and initiate first actions
d)
Rules of the Apply preventive fire protection; describe behaviour in fires and take measures to combat
4 Environmental protection
(§ 4 paragraph 2
Section C
number 4)
In order to avoid operational environmental stress in the occupational impact area, especially
a)
Possible environmental impacts of the training company and its contribution to environmental protection examples explain
b)
apply environmental protection regulations for the training establishment
c)
Possibilities of economic and environmentally friendly use of energy and materials
d)
Waste avoid substances and materials for environmentally friendly
5 Operating
communication
(§ 4 paragraph 2
Section C
number 5)
a)
Information sources, in particular documentation, Handbooks, technical reports and company records in German and English, use
b)
assemble and supplement documentation
c)
Evaluate and rate information
d)
represent facts
e)
Perform the usual written communication in German and English
f)
IT-based Using communication systems
g)
Talking with superiors, employees and the team in a situation-oriented and goal-oriented way, cultural identities take into account
h)
plan, coordinate, make decisions, and resolve conflicts in the team
i)
Perform team meetings, visualize and present facts and solutions, document conversation results, apply German and English technical terms
j)
communicate with upstream and downstream areas and external partners, coordinate submission processes, assess
6

Footnote

Asset An. B No I.6 Sp. 3 Buchst. c italic print: should be correct "allocation scheme"