Advanced Search

The Technical Conditions Of The Material Means Of Fire Protection

Original Language Title: The Technical Conditions Of Material Means Of Fire Protection

Subscribe to a Global-Regulation Premium Membership Today!

Key Benefits:

Subscribe Now for only USD$40 per month.
69/2014 Sb.



The DECREE



on 2 December. April 2014



on the technical conditions of fixed fire protection funds



The Ministry of the Interior shall establish under section 101 (a). and section 24) to implement the paragraph.

2 Act No. 133/1985 Coll., on fire protection, as amended

legislation:



§ 1



Introductory provisions



(1) this Decree lays down the technical conditions of fixed fire-fighting resources

the protection referred to in paragraph 2, the compliance with which is a condition for the

the inclusion of fixed fire protection equipment resource units

under the law on fire protection fire protection ^ 1).



(2) the material means of fire protection for the purposes of this Decree:



and used in) Terminal digital radio network PEGAS, which corresponds to the

TETRAPOL standard,



(b)) of the radio station used in analogue radio networks fire

protection (hereinafter referred to as "radio"), whose specifications are

listed in annex 1 to this notice,



c) portable syringe, whose specifications are listed in the

Annex No 2 to this Decree,



d) self-contained breathing apparatus with an open-circuit compressed air

(hereinafter referred to as "insulating breathing apparatus"), whose specifications are

listed in annex 3 to this Decree,



e) helmet for fire fighting in buildings and other areas (hereinafter referred to as

"helmet"), whose specifications are given in annex 4 to this

the Decree,



f) protective clothing for firemen (hereinafter referred to as "a low-key clothes and"), whose

the technical conditions are given in annex 5 to this Decree,



g) protective clothing for firefighters for the liquidation of fires in the open

(hereinafter referred to as "a low-key clothes II"), whose specifications are listed in the

Annex No 6 to this Ordinance,



h) supplement zásahového garment I and II (hereinafter referred to as "add-in"), whose

the technical conditions are listed in annex 7 to this Decree,



I) working uniform II, whose specifications are listed in the

Appendix 8 to this Decree, and



j) underwear for the Fire Department (hereinafter referred to as "underwear"), whose technical

the conditions are listed in annex 9 to this Decree.



(3) the technical conditions referred to in the annexes to this Decree,

be deemed to be satisfied if the proceeds in conformity with the specified standard or

parts of it under another law ^ 2), reported in the journal of the Office for

technical standardization, metrology and testing, which

contains more detailed technical requirements. These requirements can be

i met other technical solution garantujícím the same or higher

the level of protection of the legitimate interests, in accordance with this Ordinance.



§ 2



The transitional provisions of the



The means of fire protection for the benefits in kind referred to in section 1 (1). 2, included in the

fire protection equipment of the units before the date of entry into force of this

the Ordinance, applies the technical conditions laid down by Decree No. 255/1999 Coll.

in the texts of the effective to date of the entry into force of this order.



§ 3



Cancellation provisions



Shall be repealed:



1. Decree No. 255/1999 Coll., on technical conditions of factual

the means of fire protection.



2. Decree No 456/2006 Coll., amending the Decree of the Ministry of

the Interior No 255/1999 Coll., on technical conditions of factual resources

fire protection, as amended by Decree-Law No 352/2000 Sb.



3. Decree No. 102/2009 Coll., amending the Decree of the Ministry of

the Interior No 255/1999 Coll., on technical conditions of factual resources

fire protection, as amended.



§ 4



Final provision



This Decree was notified in accordance with the directive of the European Parliament

and Directive 98/34/EC of 22 December 2004. June 1998 on the procedure for the provision

information in the field of standards and technical regulations and regulations for services

the information society, as amended.



§ 5



The effectiveness of the



This Decree shall take effect on the 15th day following its publication.



Minister:



The inmate in the r.



Annex 1



THE TECHNICAL CONDITIONS OF THE RADIO STATION



1. the Base of the radio station, which is intended for radio communication in particular

with any fire protection, meets the following conditions:



and the type of broadcast or 8K50F3E), 10K0F3E or 11K0F3E,



(b)), at least 99 the number of channels,



(c) the approval for operation at least) with channel spacing 12.5 kHz



d) frequency range at least 146 to 174 MHz,



(e)) and semiduplexního operations, simplexního



f) RF power adjustable for individual channels programmatically in at least 2

levels in the range of at least 1 to 10 W,



g) NF output built-in speaker at 5% distortion = at least < 3 W,



(h) the possibility of additional speaker connection),



I) option for a reception, evaluation and posting format options for selective ZVEI

Even in the range of 1 to 3 sequences of most 9 characters, differently on

individual channel positions



j) option to specify at least one user sequence selective choice,



to view the option) at least one sequence of a selective choice of most

9 characters



l) use of CTCSS in the range 254.1 Hz up to at least 67.0 including options

specify a non-standard user format



m) use SCAN function, including the possibility of the definition of priorities and options

the temporary decommissioning of the zarušeného channel.



2. Portable radios for the team, which is intended for radio

links for intervention and other activities of units of fire protection

meets the following conditions:



and the type of broadcast or 8K50F3E), 10K0F3E or 11K0F3E,



(b) the number of at least 16 channels),



(c) the approval for operation at least) with channel spacing 12.5 kHz



d) frequency range at least 146 to 174 MHz,



(e)) and semiduplexního operations, simplexního



f) RF power adjustable for individual channels programmatically in at least 2

levels in the range of at least 1 to 5 W; for the radio station in the transposition into

potentially explosive atmospheres is determined on 1 VF W without

the request to the programme set up in at least 2 levels,



g) NF performance at 5% distortion at least < = 500 mW,



h) use of CTCSS in the range 254.1 Hz up to at least 67.0 including options

specify a non-standard user format



even the cover of at least IP 54),



j) operating temperature range of at least-25 to + 55 ° c,



the ability to switch to) posting/receiving and control channels and switches

the volume control in the protective gloves for firefighters



l) control voice (VOX)



m) the possibility to lock the keyboard, if it is equipped with a radio.



3. Portable radios for the Commander, which is intended to ensure the

radio communication with the unit commander, fire protection, other

the participants of the radio network of fire protection for intervention, or base

radio, meets the following conditions:



and the type of broadcast or 8K50F3E), 10K0F3E or 11K0F3E,



(b)), at least 99 the number of channels,



(c) the approval for operation at least) with channel spacing 12.5 kHz



d) frequency range at least 146-174 MHz,



(e)) and semiduplexního operations, simplexního



f) RF power adjustable for individual channels programmatically in at least 2

levels in the range of at least 1 to 5 W; for the radio station in the transposition into

potentially explosive atmospheres is determined on 1 VF W without

the request to the programme set up in at least 2 levels,



g) NF performance bias < = 5%, at least 500 mW,



(h)), the evaluation of income and sending a selective choice of format ZVEI

Even in the range of 1 to 3 sequences of most 9 characters, differently on

individual channel positions



I) user option to specify at least one selective choice, sequence



j) option to display at least one sequence of a selective choice of most

9 characters



to) the use of CTCSS in the range 254.1 Hz up to at least 67.0 including options

specify a non-standard user format



l) use SCAN function, including the possibility of the definition of priorities and options

the temporary disposal of zarušeného channel



m) coverage of at least IP 54,



n) operating temperature range of at least-25 to + 55 ° c,



about) the possibility of switching the broadcast/reception and control channels and switches

the volume control in the protective gloves for firefighters



p) control voice (VOX)



q) option to lock the keyboard, if it is equipped with a radio.



Car radio, which is intended to ensure the radio link

the Commander of a unit of fire protection, other participants in the radio network

fire protection for intervention, or the base radio, meets the

the following conditions:



and the type of broadcast or 8K50F3E), 10K0F3E or 11K0F3E,



(b)), at least 99 the number of channels,



(c) the approval for operation at least) with channel spacing 12.5 kHz



d) frequency range at least 146 to 174 MHz,



(e)) and semiduplexního operations, simplexního



f) RF power adjustable for individual channels programmatically in at least 2

levels in the range of at least 1 to 10 W,



g) NF output built-in speaker at 5% distortion = at least < 3 W,



(h) the possibility of additional speaker connection),



I) option for a reception, evaluation and posting format options for selective ZVEI

Even in the range of 1 to 3 sequences of most 9 characters, differently on

individual channel positions



j) option to specify at least one user sequence selective choice,



to view the option) at least one sequence of a selective choice of most

9 characters



l) use of CTCSS in the range 254.1 Hz up to at least 67.0 including options

specify a non-standard user format
m) use SCAN function, including the possibility of the definition of priorities and options

the temporary disposal of zarušeného channel



n) operating temperature range of at least-25 to + 55 ° c.



Annex 2



TECHNICAL CONDITIONS OF PORTABLE MOTOR SYRINGE



1. Portable syringe meets the requirements of the standards listed in section 1

paragraph. 3 on the syringe that uses a portable motor fire centrifugal

the pump is a device its intake manifold for hydration.



2. the motor is equipped with a Portable fire pump centrifugal

the pump, which indicates the value of the nominal performance of the fire

the pump in accordance with the parameters specified rated speed,

the rated discharge pressure (bar), the nominal suction height survey

the nominal flow of the pump (URl.min-1). Marking of portable motor

the syringe is indicated by the abbreviation in the area of fixed position,

sans-serif font, letters by great alphabet. Portable motor

the syringe is referred to by the abbreviation:



and at the nominal flowrate) 750-7.5 URl.min PS,



(b)) at the nominal flow rate 1000 URl.min-PS 10, or



(c)) at the nominal flow 1500 URl.min-PS 15.



3. If the nominal flow rate of fire between the centrifugal pump

described the values, the size of the nominal flow of the fire pump

indicates according to the nearest lower nominal flow rate values.



The basic functions of a portable motor syringe



4. construction of portable motor syringe allows you to:



and irrigate the intake duct) from an outside source when the device zavodňovacím

suction height of 7.5 m,



(b)), and transport water pumping hoses from outside the free resources,



(c) water hoses at) connection to an external pressure source

input pressure of at least 1.5 bar.



5. suction the throat for portable motor syringe is 110 mm threaded according

the standards referred to in section 1 (1). 3.



6. suction and delivery of the throat are escorted out to the space in which do not restrict the

operation.



7. Portable motor pump is equipped with at least one discharge

diameter 75 mm, provided with shut-off valves with clutch by

the standards referred to in section 1 (1). 3, written into the side of the longitudinal axis

fire pump. The number of nozzles vacuum/pressure corresponds to the nominal flow

fire pump. The height of the lower edge of the discharge neck at least 250

mm above the ground.



8. construction of portable motor syringe allows for continuous operation

for 8 hours so as not to exceed the permissible temperature of the engine

and possible transmission to the pump.



9. If the syringe equipped with portable battery

the batteries, then it is designed for continuous recharging rechargeable batteries

by using the element located in the area of fixed position.



Centrifugal fire pump



10. Fire the centrifugal pump is fitted with a non-return valve to protect the

suction hose against damage to the pressure and the pressure relief device.



11. Head neck of the fire including the centrifugal pump control

valves are 15º below the horizontal, for the purpose of their

drainage.



Annex 3



THE TECHNICAL CONDITIONS FOR THE ISOLATION OF RESPIRATORY EQUIPMENT



1. Insulating the appliance meets the requirements of the standard referred to in section 1 of the

paragraph. 3 on the autonomous breathing apparatus with compressed air, open

circuit with a full face mask that is used as a means to protect

respiratory organs.



2. Insulating breathing apparatus is classified as type 2 in accordance with the standards

referred to in section 1 (1). 3.



3. Insulating the appliance allows you to use one cylinder on

water volume 6 to 9 litres or two bottles of water pressure on the volume

each of them 6 to 7 litres filling pressure 30 MPa (300 bar). Crash

You can also use the cylinder for a water volume of 5 and 7 litres with filling

the pressure of 20 MPa (200 bar).



4. the maximum working pressure of insulating breathing apparatus is 30 MPa (300

bar).



5. design of the insulating breathing apparatus may enable the second input

and output for remote air supply or other face mask or

the emergency feed-out hood or ventilation protichemického protection

the garment. The provisions of this section shall not apply to the device with the highest

working pressure 20 MPa (200 bar).



6. the straps and the corpus of insulating breathing apparatus are manufactured from

materials that allow the wet way of decontamination at a temperature of up to 100

° C without damage; part of the porous materials are removable and

removable.



7. the weight of the apparatus with a full face mask and completely filled with pressure

cylinders (pressure bottles), which is ready to use, may not be

more than 15 kg.



8. Control valves to start insulating breathing apparatus is for

the wearer with both hands easily accessible.



9. Insulating breathing apparatus has a manually controlled auxiliary supply

the air.



10. the additional Control of the air supply must be made in the trade

gloves for firefighters.



11. Insulating the appliance is made of materials that make it impossible

formation and discharge of static electricity.



12. Insulating breathing apparatus has an acoustic or pneumatic. (I)

electronic warning device.



13. The barometer to check excess pressure in the cylinder for the stocks discovery

the air is located on the left shoulder strap in position, allowing the

control of the bearer and detection in MPa or bar; the barometer has

the red box in the range of 0 to 5 MPa (0 to 50 bar).



Pressure cylinder



14. metal pressure bottle is approved under another legal regulation ^ 3.



15. Marking of cylinders must be durable. Allows you to uniquely

identify the pressure bottle and its contents. The pressure of the cylinder must be

marked at the same time the color marking, stamping or epoxy resin cylinder

the printed label under the plastic film and removable markings

safety stickers in accordance with standards referred to in section 1 (1). 3.



16. Composite pressure cylinder is protected by removable cover blue

colors. Part of the package is a vertical strip of spectacular material of

width of 75 mm. Packaging and the belt is made from materials with restricted dissemination

the flame and is resistant against mechanical damage. The belt consists of three

the bars; the upper and lower third of the width of the yellow color is fluorescent and

the middle third of the color silver with retroreflexními properties under

the standards referred to in section 1 (1). 3.



17. Connect the pressure bottle to izolačnímu ventilator is

done a G thread 5/8 ", in accordance with the standards referred to in section 1 (1). 3.



18. Part of the pressure of the cylinder or valve of the pressure cylinder is a safety

element, which in the case of damage to the valve restricts flow of leaks

from the pressure of the cylinder so that the reaction force will not cause the uncontrolled movement of

of the cylinder.



Face mask



19. Face mask allows the fastening of the Greek cross, or

by using the rychloupínačů.



20. Facial mask can be equipped with a device for voice

communication using radio, or other communication medium.



Annex 4



THE TECHNICAL CONDITIONS FOR THE HELMETS



1. the Helmet meets the requirements of the standard referred to in section 1 (1). 3 on the helmet

providing the user head protection when disposing of the fires and the accompanying

activities and even in situations that you can meet when disposing of

fires in the buildings.



2. The surface of the helmet and helmet wet exhibit dielectric resistance,

the helmet can be on the basis of electrical properties for inclusion in the category E2 and

E3 in accordance with standards referred to in section 1 (1). 3.



3. the Helmet meets the requirements of the standard referred to in section 1 (1). 3 at-30 ° c, you can

it according to the standards listed in section 1 (1). 3 include in the category called

"***".



4. Part of the helmet's chinstrap unilaterally, however, in

gloves for firefighters.



5. Part of the helmet's neck protector (nátýlník).



6. Part of the helmet's face shield, which provides protection to the eyes and

a substantial part of the face. facial protector. Part of the helmet can

at the same time also be a protector of eyes, if it can be used independently of the

the wheel face.



7. All the components of the helmet are removable in the framework of maintenance.



8. helmet allows you to:



and the use of facial masks) insulating breathing apparatus with all the

ways of fastening in accordance with annex 3, paragraph 19 of this order,



(b)) fit the lamp,



(c) the installation of a device that enables the combined) control of the radio station voice

and the press and Assembly Speaker,



(d)) position for marking elements self-adhesive firefighters, on the surface of the shell

Helmets.



9. the material of the shell is executed in the colour yellow, yellow, fluorescent,

or yellow-green luminescence.



10. helmet in the equipment of the fire brigade of the Czech Republic

the surface of the shell can be executed in a different color than is specified in point

9.



Annex 5



TECHNICAL CONDITIONS OF ZÁSAHOVÉHO CLOTHING AND



1. A low-key clothes and meets the requirements of the standard referred to in section 1 (1). 3 on

protection of the body except for head, hands and feet in the liquidation of fires and

accompanying activities and even in situations in which you can meet

When disposing of the fires in the buildings.



2. Strike the garment and is executed as a two-part, consists of a jacket and

pants.



3. The outer material of the garment and zásahového:



and) is resistant to abrasion, can withstand when testing in accordance with the standards referred to in section 1 of the

paragraph. 3 without damage to at least 40, 000 RPM test equipment,
(b)) is a colorful, is at least grade 4 gray scale in

testing of colour fastness in mechanical washing at 60 ° c, in sweat and in

dry abrasion and grade 3 in wet abrasion in accordance with the standards referred to in section 1 of the

paragraph. 3.0,



c) is resistant to Pilling, showing when testing in accordance with standards referred

in section 1 (1). 3 resistance to pilling at least grade 4,



d) meets the requirements for material diffusing electrostatic charge

in accordance with the standards referred to in section 1 (1). 3,



(e)) is executed in dark blue colour with the exception of about of material.



4. In the zásahovém clothing and can be integrated with personal protective equipment

against falls from heights.



5. A low-key clothes and can be equipped with the technical elements, such as

for example, the loops for attaching the lamp, facial masks, insulation

breathing apparatus or accessories radio, if significant

in a way it does not change the appearance of the garment.



6. Low-key clothes I may be in the area of the shoulder, elbow and knee stiffened with

the next layer of the outer material of the garment, or with material with a higher

mechanical resistance in the color dark blue or black.



7. Low-key clothes and can be cleaned by mechanical washing water temperature 60

° C.



Coat



8. The coat is



and the zippy) carrying the légou zapínanou on the stuhový CAP,

where appropriate, the stuhový closure with metal connectors; fastener and connector is

possible to switch on protective gloves for firefighters



(b)) at the bottom of both front parts, Pocket, covered heel with

stuhové caps; in at least one of these pockets is placed the strap,



(c)), at least one internal Pocket measuring at least 150 x 180 mm

bearing strength or other closing device



(d)) at the top of the left front pocket part for the location of the radio station;

the Pocket is in such implementation, in order to ensure the consolidation of

the radio at work,



e) inside the sleeve of the knitted fabric of both closing with palečnicí.



9. In the upper right of the front part of his coat may be placed part of the

stuhového closure with loops on the dimensions of 70 x 38 mm mounting

hodnostního or functional designation and below for more about the dimensions of 125 x 25

mm for the attachment of a label or a personal registration number.



Pants



10. Pants have



and) increased waist and braces,



(b)) slit indoor légou with fixation to prevent its opening at work.



11. The size of the circumference of the waist of the trousers can be edited, for example, the sewn

the eraser or a belt to regulate.



12. Pants may have over the right or left side seam Pocket našitu

covered heel with stuhové caps.



13. Pants may have at the bottom of the pant leg inside the cuff.



Garment processing



14. zásahového garment and Processing is done in the following way:



and) all seams are secured against fraying, obnitkováním



(b)), in particular for the coat are the seams for a join of the front parts with the back of the work,

parts of the sleeves, the edge of the collar, presser feet, and prošity on the průramcích extention

dvoujehlovém sewing machine,



(c)) are in particular the trouser seams for a join back and front parts and seams

on foot and on the edge of the cover to the dvoujehlovém rozparku prošity légy sewing

the machine,



(d)) the beginning and end of machine sewing reverse tacking is ensured

at least 10 mm in length,



(e) the number of stitches) on 10 mm machine sewing is at least 3.5,



(f)) stuhové caps are enough saved. around the circuit with

sufficient tacking,



(g)) sewing or decorative stitching does not download or orogeny of the seams,



h) Pocket and shoe are firmed up deadlines,



I) end of the thread around the hair product.



Conspicuous material



15. On the top of the back part of the coat above the belt is in the yellow box

fluorescent colors, dimensions 290 x 75 mm, the inscription "FIRE BRIGADE".

The inscription is made in capitals in bold type, Switzerland

the color of the outer material of the garment. The length of the banner is 260 mm, height of the font

(without hook) is 55 mm, the width of the font is 12 mm. Below the words "FIRE BRIGADE" may

be carried out in a similar way the inscription indicating affiliation to the unit

fire protection.



16. Belt width 75 mm, consisting of three bars; the upper and lower third of the

its width is a yellow fluorescent colors and the middle third of the

Silver with retroreflexními properties, and is placed around the perimeter:



and the coat of the breast) and allows the location of the frames with the inscriptions referred to in point

15,



(b)) the bottom of the coat,



(c)) of the breast of his coat sleeves and at the bottom of the sleeves,



(d)) the bottom of the pant leg.



17. The bottom edge of the Ribbon is placed at a distance of at least 50 mm from the

the bottom edge of coat sleeves and pant legs.



Annex 6



TECHNICAL CONDITIONS OF THE ZÁSAHOVÉHO CLOTHING II



1. A garment (II) meets the requirements of the standard referred to in section 1 (1). 3 on

protection of the body except for head, hands and feet in the liquidation of fires in

open terrain and accompanying activities.



2. Strike the garment is carried out as a two-part II, consists of a blouse and

pants.



3. the external material zásahového garment (II):



and) is resistant to abrasion, can withstand when testing in accordance with the standards referred to in section 1 of the

paragraph. 3 without damage to at least 40, 000 RPM test equipment,



(b)) is a colorful, is at least grade 4 gray scale in

testing of colour fastness in mechanical washing at 60 ° c, in sweat and in

dry abrasion and grade 3 in wet abrasion in accordance with the standards referred to in section 1 of the

paragraph. 3,



c) is resistant to Pilling, showing when testing in accordance with standards referred

in section 1 (1). 3 resistance to pilling at least grade 4,



d) meets the requirements for material diffusing electrostatic charge

in accordance with the standards referred to in section 1 (1). 3,



(e)) is executed in dark blue colour with the exception of about of material.



4. Strike garment II can be equipped with the technical elements, such as

for example, the loops for attaching the lamp, facial masks, insulation

breathing apparatus or accessories radio, if significant

in a way it does not change the appearance of the garment.



5. Strike garment II may be in the area of the shoulder, elbow and knee stiffened with

the next layer of the outer material of the garment, or with material with a higher

mechanical resistance in the color dark blue or black.



6. Low-key clothes (II) can be cleaned by mechanical washing water temperature 60

° C.



Tunic



7. the Tunic has:



and the zippy) until the collar of the shape of the floor after, roofed légou

full length, zapínanou on the stuhový Cap; fastener can be switched on in

protective gloves for firefighters



(b)) at the bottom of both front parts, Pocket, covered heel with

stuhové closures,



(c)) at the top of the right front pocket part a covered heel with

the closures, stuhové



(d)) at the top of the left front pocket part for the location of the radio station;

the Pocket is in such implementation, in order to ensure the consolidation of

the radio at work,



(e)) back in the bottom of the elongated,



(f)) in the passport section of a sewn-on side of cheek, with the tunnel, provlečenou, elastic band



g) into the cuff sleeves finished downloaded at the bottom of an



(h)), on the manžetách sleeve patch spínadlo with stuhový Cap.

Part of the stuhového closure with hooks is a našitá on the spínadle.



8. In the upper right part of the front blouse, over the Pocket, can be

přišita part stuhového Cap with loops on the dimensions of 70 x 38 mm

the attachment of the hodnostního or functional designation and below for more about the

dimensions 125 x 25 mm for the attachment of a label or personal ID.

the numbers.



Pants



9. Pants are:



and všitý shaped wedge) in stepper and sedové part, to facilitate the free

the movement and the increasing strength of the pants in the crotch,



(b)) slit with zippy covered légou,



(c)) at the top of both front parts všity slanted pockets with button fastening

zippy, with handheld bags from the surface of the material,



(d)) at the bottom of the pant leg patch spínadlo, article stuhový Cap.

Part of the stuhového closure with hooks is a našitá on the spínadle,



e) increased Passport collar with belt loops on the belt and suspenders, in front zapínaný

part of the druk,



(f)), removable adjustable suspenders.



10. The size of the circumference of the waist of the trousers can be edited, for example, the sewn

the eraser or a belt to regulate.



11. Pants may have over the right or left side seam Pocket našitu

covered heel with stuhové caps.



Garment processing



12. zásahového garment Processing (II) is made in the following manner:



and) all seams are secured against fraying, obnitkováním



(b)) for at least the blouse seams for a join of the front parts with the back of the work,

parts of the sleeves, and the seams on the saddle, the edge of the collar, patek, légy and průramcích

prošity on dvoujehlovém sewing machine,



c) trousers are of at least the seams for a join back and front parts and seams

on foot and on the edge of the cover hook prošity to dvoujehlovém extention

the sewing machine,



(d)) the beginning and end of machine sewing reverse tacking is ensured

at least 10 mm in length,



(e) the number of stitches) on 10 mm machine sewing is at least 3.5,



(f)) stuhové caps are enough saved. around the circuit with

sufficient tacking,



(g)) sewing or decorative stitching does not download or orogeny of the seams,



h) Pocket and shoe are firmed up deadlines,



I) stuhové caps are sewn on the bottom works only on the feet, extention,



j) end of the thread around the hair product.



Conspicuous material
13. On the top of the back part of the blouse above the belt is in the yellow box

fluorescent colors, dimensions 290 x 75 mm, the inscription "FIRE BRIGADE".

The inscription is made in capitals in bold type, Switzerland

the color of the outer material of the garment. The length of the banner is 260 mm, height of the font

(without hook) is 55 mm, the width of the font is 12 mm. Below the words "FIRE BRIGADE" may

be carried out in a similar way the inscription indicating affiliation to the unit

fire protection.



14. A strip of yellow color with a width of 50 mm, made of a material with

combined properties, and is placed around the perimeter:



and blouses of the breast) and allows the location of the frames with the inscriptions referred to in point

13,



(b)) the bottom of the blouse,



(c)) of the sleeves of the blouse of the chest and at the bottom of the sleeves,



(d)) the bottom of the pant leg.



15. The lower edge of the Ribbon is placed at a distance of at least 50 mm from the

the lower edge of blouse, sleeves and pant legs.



Annex 7



TECHNICAL CONDITIONS FOR



1. Complementary means undershirt with long or short sleeves and pants

with long sleeves that are used to increase the protection against heat and

the flame and the improvement of the comfort and thermoregulation.



2. the Supplement meets the General requirements for protective clothing in accordance with standards

referred to in section 1 (1). 3.



3. All materials for limited flame spread index 2 or

3 in accordance with the standards referred to in section 1 (1). 3.



4. The basic material for:



and,) is a colorful, is at least grade 4 gray scale in

testing of colour fastness in mechanical washing at 40 ° c and in sweat according to

the standards referred to in section 1 (1). 3,



(b)) is to maintain the size of the standing, it shows during testing according to standards

referred to in section 1 (1). 3 change the dimensions in both directions < = +-5%,



c) is resistant to Pilling, showing when testing in accordance with standards referred

in section 1 (1). 3 resistance to pilling at least grade 4,



(d)) has the least good thermoregulatory properties in accordance with standards referred

in section 1 (1). 3.



5. The add-in is done in dark blue color.



6. the Supplement can be cleaned by mechanical washing water temperature 40 ° c.



7. The edge of the sleeves for nátělníku, and for průkrčník leg of pants are

made of flexible trim.



8. Průkrčník is round, or accompanied by a collar of a width of approximately 80 mm and

on the front légou zapínanou on the three buttons with a length of approximately 150

mm.



9. Cut for is clinging.



10. The seams are straight, regular and flexible.



11. The end of the seam are resistant to ripping and the end of the thread odstřiženy.



12. On the left the thoracic part of the nátělníku can be made rukávový the character and

designation of jurisdiction over him to drive fire protection or

the organizational part of the fire brigade of the Czech Republic white

color or colour under other legislation ^ 4.



Annex 8



TECHNICAL CONDITIONS OF WORK UNIFORMS (II)



1. These technical conditions apply to work uniforms (II) according to the

§ 1 (1). 1 (a). (b)) Decree No. 97/2008 Coll., on business models

uniforms, members of the fire brigade of the Czech Republic,

their use and how the outer markings, and the model of professional

the card (the Decree on the influence and the staff members of the card

Fire brigade of the Czech Republic) and under section 43, paragraph. 1 and 2

Decree No. 247/2001 Coll., on the Organization and activities of units of fire

protection, as amended.



2. the work uniforms (II) meets the General requirements for protective clothing

in accordance with the standards referred to in section 1 (1). 3.



3. the work uniforms (II) consists of a blouse or Polo shirts, trousers and

caps.



4. the basic material of the blouse, pants and hats:



and) is resistant to abrasion, can withstand when testing in accordance with the standards referred to in section 1 of the

paragraph. 3 without damaging at least 30 000 RPM test equipment,



(b)) is hard, can withstand in the transverse and longitudinal direction when tested in accordance

the standards referred to in section 1 (1). 3 strength > = 450 N,



c) is resistant to tear, showing when testing according to standards

referred to in section 1 (1). 3 in the transverse and longitudinal direction resistance against further

tearing > = 20 N,



(d)) is a colorful, is at least grade 4 gray scale in

testing of colour fastness in mechanical washing at 60 ° c, in sweat and in

dry abrasion and grade 3 in wet abrasion in accordance with the standards referred to in section 1 of the

paragraph. 3,



(e)) is resistant to Pilling, showing when testing in accordance with standards referred

in section 1 (1). 3 resistance to pilling at least grade 4,



(f)) is permeable to water vapour, it shows during testing according to the standard

referred to in section 1 (1). 3 the average water vapour resistance < = 10 m2

Pa/W,



(g)) is carried out in a dark blue colour.



5. the basic material of the shirt:



a) meets the requirements referred to in point 4 (b). (d)), e) and (g)),



(b)) has at least a good thermoregulatory properties in accordance with standards referred

in section 1 (1). 3.



6. the work uniforms II is dimensionally stable, maintenance testing

in accordance with the standards referred to in section 1 (1). 3 change the dimensions of the blouse and pants in

both directions < = +-3%, Polo shirts in both directions < = +-5%.



7. the working uniforms II has fixed the main seams, when testing according to standards

referred to in section 1 (1). 3 are the main stitching blouses and pants-resistant strength

> = 225 N.



8. Blouse pants can be cleaned by mechanical washing water temperature 60 ° c,

polokošili a water temperature of 40 ° c.



9. the Tunic and trousers are made in variant A or B.



10. the Tunic and trousers made in and according to the standards listed in section 1

paragraph. 3:



and) are heat-resistant temperature (180 +-5) ° c,



(b)) exhibit limited flame spread,



(c)) provide protection against heat, konvekčnímu level of at least

B1,



(d)) provide protection against radiant heat, at least level C1.



11. the basic material of the blouse and pants made in and meets the

the requirements for material diffusing electrostatic charge according to standards

referred to in section 1 (1). 3.



12. the basic material of the blouse and pants made in variant B and basic

the material of the shirt is durable against heat at a temperature (180 +-5) ° c

in accordance with the standards referred to in section 1 (1). 3.



Tunic



13. the Tunic has:



and the front parts and) over the rear part of the saddle patch of the surface of the material,



(b)) at the top of both the leading parts in his breast pocket on upper pickled

the dimensions of 150 x 180 mm with base plate into shape with stuhové

closures,



(c)) to the bottom of both side seams sewn pockets with handheld bags from

the surface of the material,



(d)) the fastener from the neckline to the bottom edge of the overlapping

légou stitched on the left front, with 5 PC stuhových

Cap width 25 mm and a length of 50 mm,



(e)) at the back under the saddle of the folds are made towards the side švům.

The bottom half of the folds is zašita,



f) one-piece hlavicové sleeves, culminating with a cuff, downloaded through the lower

part of the elastic band width 20 mm in two rows,



g) on manžetách Seun spínadlo with stuhový Cap. The part of the

stuhového closure with hooks is a našita on the spínadle,



(h) the one-piece collar) rožcích odšitý and the stitched. To the neckline

the wrist strap is sewn in hooks. On the lower collar is našita spínka,

opening stuhový Cap



even) lower region completed the band, through the rear and front part of the workpiece

downloaded elastic band width 20 mm in two rows,



(j)) above the Centre of the right breast pocket, between the base and the seat, našitu part

stuhového caps with loops, measuring 70 x 38 mm, for the attachment of

hodnostního or functional designation,



k) over the Centre of the left breast pocket, between the base and the seat, našitu part

stuhového caps with loops, with dimensions of 125 x 25 mm, for the label

or personal registration number.



14. Tunic made in variant B has the horizontal seams for a join

the saddle with front parts and back part, throughout their length všitu

paspuli yellow-green color of the range of 2 to 4 mm.



Polo shirts



15. Polo has:



and short sleeves),



(b) the collar of a width of approximately) 80 mm,



(c)) on the front in the upper part of the légu zapínanou to the three buttons on the length of the

approximately 150 mm,



(d)) at the top right of the front part of the closure is a convenient part of the stuhového

loops with dimensions of 70 x 38 mm, for the attachment of the marking, hodnostního



(e)) in the upper left of the front part of the closure is a convenient part of the stuhového

loops on the dimensions of 125 x 25 mm, for the label or personal

the registration number.



Pants



16. The pants are:



and on the front works created) the folds pointing to the side seam,



(b)) on the rear parts odšité tucks,



(c)) at the top of the two front side pockets, wedge-shaped parts



(d)) at the top of the right rear jednovýpustkovou with pedestal

to shape, with stuhový Cap



e) through right side seam Pocket dimensions našitu a 180 x 190

mm covered heel into shape with stuhové caps; the Pocket is

located at a distance of approximately 360 mm from the edge of the collar with a passport

given the size of the pants,



f) vent opening on the zipper or buttons,



g) passport collar with podšitím 50 mm, through the side seam of the downloaded elastic band width

20 mm in two rows. Pruženka is sewn from their lateral wedge Pocket

back to záševku. Passport in front of the collar is switched on for 2

buttons or druk, Seun pasovém collar is 7 loops on the belt on
width 20 mm. On the top side of the Passport collars are stitched the buttons for

attach the braces.



h) lower edge of pant leg podehnutý and stitched,



I) at the bottom of the rear parts of patch spínadlo length 90 mm, and the width of 35

mm, article stuhový Cap. Part of the stuhového closure with hooks is a

našita on spínadle,



j) width 40 mm belt black color with a snap buckle black color or braces.



k) buttons with a diameter of 16 mm, with four holes that are saved in the

the number of 2 buttons on the right side of the collar for the Passport to turn on your pants,

If the button is not used, the 6 buttons on the top of the collar on the Passport

attach the braces and the 3 buttons in the rozparku, if it is not applied to the fastener.



17. The trousers produced in the variant and have to seam on the outside of the leg

throughout their length všitu paspuli yellow-green color of the range of 2 to 4 mm.



Caps



18. Caps:



and six panels) stapled to each rovnostehem. This seam is the reverse

the Parties covered by the piping and prošit dvoujehlou with rozpichem 10 mm.



(b)) two front panels of the reverse side of the fabric, reinforced with podlepením



c) plastic molded with six stitched and trimmed the outer

material,



(d)) from the inside všit reinforced black sweat headband,



e) fastening the metal clip made with oval manhole to hide

the end of the tape, in the upper part, always in the middle of the panels, metal vent

holes with a hole about the size of 4 mm,



(f)) on the canopy caps plastic knob, which is coated with an external

material.



19. The caps can have on the forehead above the plate the inscription "FIREMEN",

embroidery size 58 x 16 mm (without hook), in capitals

Grotesk medium type. The bottom of the embroidery is 30 mm above the plate. Embroidery is

made on the center of the forehead Cap. This is without prejudice to the provisions of other

^ law 5.



20. the Cap can have the edges of the label všitu paspuli yellow-green color.



Processing of uniforms



21. the processing of the work is done by the following uniforms II

way:



and all the seams are secured) ripping and fraying against obnitkováním,



(b)) for at least the blouse seams for a join of the front parts with the back of the work,

and the seams on the saddle, the edge of the collar, pockets, the housing cover tray fastener and

průramcích prošity on dvoujehlovém sewing machine,



c) trousers are of at least the side seams for a join back and front parts

and the seams of the pockets on the edge of the housing and the cover hook at prošity extention

dvoujehlovém sewing machine,



(d)) the beginning and end of machine sewing reverse tacking is ensured

at least 10 mm in length,



(e) the number of stitches) on 10 mm machine sewing is at least 3.5,



(f)) stuhové caps are enough saved. around the circuit with

sufficient tacking,



(g)) sewing or decorative stitching does not download or orogeny of the seams,



h) all stressed places such as pockets, feet and their rozparku,

deadlines are concreted over,



I) stuhové caps are sewn on the bottom works only on the feet, extention,



j) end of the thread around the hair product are properly.



Conspicuous material



22. The striking material is placed only on the blouse manufactured in the Variant.



23. the material meets the conditions for Striking a highly noticeable yellow material

the colors according to the standards listed in section 1 (1). 3.



24. On the top of the back part of the blouse, a 10 mm below the seat, is in the yellow box

fluorescent colors, dimensions 290 x 75 mm, the inscription "FIRE BRIGADE".

The inscription is made in capitals in bold type, Switzerland

the color of the base material for uniforms. The length of the banner is 260 mm, height

font (without hook) is 55 mm, the width of the font is 12 mm.



25. A highlight tape of yellow color with the combined characteristics of a width of

25 mm is placed on the front and on the back "so that his

the bottom edge is positioned 10 mm from the saddle.



Annex 9



TECHNICAL CONDITIONS OF UNDERWEAR



1. Underwear means a t-shirt with long or short sleeves and

pants with long or short sleeves.



2. Lingerie meets the General requirements for protective clothing in accordance with

the standards referred to in section 1 (1). 3.



3. Lingerie:



and,) is a fast is at least grade 4 gray scale in

testing of colour fastness in mechanical washing at 40 ° c and in sweat according to

the standards referred to in section 1 (1). 3,



(b)) is to maintain the size of the permanent exhibit in the testing according to standards

referred to in section 1 (1). 3 change the dimensions in both directions < = +-6.5%,



c) is resistant to Pilling, showing when testing in accordance with standards referred

in section 1 (1). 3 resistance to pilling at least grade 4,



d) is carried out in the color gray or grey mixture yarns.



4. Material underwear:



and the knitwear knitted binding) has a covered, hems hand beneath that Zebra 1:1



(b)) is performed on a single machine, round fender on a double,



(c)) has the composition of 60% cotton, 40% viscose, rims are made of

the material composition of the 58% of cotton, viscose elastane 38.5%, 3.5%, auxiliary

threads are of polyester or polyester/cotton,



(d)) has weight in the table with a tolerance of +-8%:



------------------------------------------------------------------------------------------

Kind of underwear Basic material Borders

------------------------------------------------------------------------------------------

T-shirt with long sleeves and pants with long sleeves 265g 180 g/m2/m2

------------------------------------------------------------------------------------------

T-shirt with short sleeves and pants with short trousers 140 g/m2 200 g/m2

------------------------------------------------------------------------------------------



5. Lingerie can be made from a different material than indicated

in section 4, if this material:



and the least good) shows a thermoregulatory properties according to the standards

in section 1 (1). 3,



(b)), it is resistant against heat at a temperature (180 +-5) ° c in accordance with standards referred

in section 1 (1). 3.



6. The edge of the sleeves with shirts with long sleeves, trousers for pants with long

trousers and průkrčník are constructed of flexible trim.



7. Průkrčník is round.



8. The seams are straight, regular and flexible.



9. The end of the seam are resistant to ripping and the end of the thread odstřiženy.



10. On the left the thoracic part of the t-shirts can be made rukávový the character and above

it indicate the nationality of the fire protection unit, or organizational

part of the fire brigade of the Czech Republic in black or in

colour under other legislation ^ 6.



section 65 paragraph 1). 1 of law No. 133/1985 Coll., on fire protection, as amended by

amended.



2) Section 4a of the Act No. 22/1997 Coll., on technical requirements for products and on the

changing and supplementing certain acts, as amended.



3 Decree No. 18/1979, which determined the reserved pressure equipment

and lays down certain conditions to ensure their safety, as amended by

amended.



4 § 5 and 6 of Decree No. 97/2008 Coll., on completion, and the staff of the card

members of the fire brigade of the Czech Republic.



section 43 paragraph. 4 and 5 of Decree No 247/2001 Coll., on the Organization and activities of the

fire protection units, as amended by public notice. 226/2005 Sb.



§ 5, paragraph 43. 6 Decree No 247/2001 Coll., on the Organization and activities of the

fire protection units, as amended by no. 226/2005 Sb.



6 section 5 and 6 of Decree No. 97/2008 Coll., on completion, and the staff of the card

members of the fire brigade of the Czech Republic.



section 43 paragraph. 4 and 5 of Decree No 247/2001 Coll., on the Organization and activities of the

fire protection units, as amended by Decree No 226/2005 Sb.