208/2015 Sb.
REGULATION OF THE GOVERNMENT
of 29 April 2004. July 2015
on technical requirements for pyrotechnic articles and their placing on the
market
The Government ordered under section 7 (2). 3, § 8 paragraph. 3, § 9 (2). 4 and section 10, paragraph 1.
3 of Act No. 206/2015 Coll., on pyrotechnic articles and the treatment of
them and on the amendment of certain laws (law on the pyrotechnics), (hereinafter referred to as
the "law"):
§ 1
The subject of the edit
This regulation incorporates the relevant provision of the European Union "^ 1") and modifies the
and a description of the contents of each) and conformity assessment procedures, including
documentation, to be kept for each assessment procedures
compliance, and the procedure of the manufacturer and the notified body for individual procedures
conformity assessment,
(b) the scope and description of the documentation), belonging to each of the procedures
conformity assessment,
(c) a description of and requirements for certificate) of the EU type-examination certificate and
conformity assessment,
(d)) the model of the EU Declaration of conformity.
§ 2
Conformity assessment procedures
Description and contents of each conformity assessment procedures including documentation,
that has to be kept for each conformity assessment procedures, and
the procedure of the manufacturer and the notified body for individual assessment procedures
of conformity is given in annex 1 to this regulation.
§ 3
Documentation
Documentation attached to the application for assessment of conformity of the
the EU type-examination)
1. technical documentation and
2. the supporting evidence for the adequacy of the technical design solution; support
the evidence must refer to documents that have been applied, in particular where the
harmonised standards have not been applied in full; If it is necessary to
demonstrating the adequacy of the technical solution, supporting evidence include
also, the results of the tests carried out in accordance with other technical
specifications laboratory of the manufacturer or other testing laboratory its
behalf and under his responsibility,
b) conformity to type based on quality assurance of the production process
1. information about the pyrotechnic category envisaged,
2. the documentation of the quality system and
3. the technical documentation of the approved type and a copy of the certificate of the EU
type-examination,
c) conformity to type based on quality assurance of the product
1. information about the pyrotechnic category envisaged,
2. the documentation of the quality system and
3. the technical documentation of the approved type and a copy of the certificate of the EU
type-examination,
d) conformity based on comprehensive quality assurance
1. the technical documentation for one model of each category of
pyrotechnic articles, which they produce, and
2. the documentation of the quality system.
§ 4
The technical documentation
(1) the technical documentation must enable the conformity of the
a pyrotechnic product with the requirements of the Act and includes the corresponding
analysis and risk assessment.
(2) the technical dossier contains at least
and a general description of the pyrotechnic article),
b) conceptual design and manufacturing drawings and schemes of components, subassemblies,
circuits, and possibly other parts of the product, including their descriptions and
the explanatory notes,
(c)) the list of harmonised standards, which were wholly or partly used, and
for which references have been published in the official journal of the European Union, and
a description of the solutions adopted to meet the essential safety requirements
the law; list of other relevant technical specifications
have been used, if harmonized standards have not been applied; in the case of
partially applied harmonised standards, the technical documentation
bring those parts which have been applied,
d) results of design calculations carried out examination and, where applicable,
other information necessary for the assessment of conformity of a product, and
e) protocols on the testing carried out.
§ 5
The quality system documentation
(1) the quality system documentation must permit uniform interpretation of
programmes, plans, manuals and quality records.
(2) documentation of the quality system contains
and quality objectives,) a description of the organizational structure, responsibilities and powers of the
of the management with regard to product quality,
(b) a description of the examination and tests), which will be carried out before,
during and after manufacture, the frequency with which,
(c) a description of quality records), in particular the Protocol on inspections, the records of the
tests carried out, records of calibration and
the qualifications of the staff concerned, and
d) description of the means of monitoring the effective operation supervision
the quality system.
(3) quality system documentation in the assessment of conformity to type based
on the quality assurance of the production process includes in addition to the data referred to in
paragraph 2 of the description of the respective methods, processes and systematic
the measures that will be used in the manufacture and inspection and quality assurance
the quality.
(4) documentation of the quality system in conformity assessment based on
comprehensive quality assurance includes, in addition to the data referred to in paragraph 2
and the respective methods) description of the processes and systematic measures that
will be used in the manufacture and inspection and quality assurance techniques,
(b)) description means to monitor the achievement of the required
the quality of the design of the products,
(c)) the technical design specifications, including standards, that will be used; in
where the relevant harmonised standards fully apply description
the funds, which will be used to ensure that the essential
the security requirements of the Act, and
(d) a description of the control methods of the proposal) and verifying the design, procedures and
systematic actions that will be used when designing the
pyrotechnic articles belonging to the category
pyrotechnic articles.
§ 6
The EU type-examination certificate
(1) the EU type-examination Certificate and its annexes shall contain the information
enabling
and) evaluate whether pyrotechnic products are manufactured in conformity with the
the type which has passed the assessment of the conformity of the EU type-examination, and
(b)) to perform a validation check on the manufacturer's specified requirements.
(2) the EU type-examination Certificate contains
and) the business name and address or name, surname and the address of the place of residence
the manufacturer,
(b)), conclusions of the examination,
(c) the conditions of validity of the certificate), if they are determined, and the
d) data necessary to identify the approved type.
(3) if they are carried out modifications to the approved type of pyrotechnic
the product, which may affect its compliance with the essential safety
the requirements of the law or the conditions of validity of the certificate,
part of the EU type-examination certificate supplement, which are
These adjustments.
section 7 of the
The certificate of conformity
Certificate of conformity contains
and information about the fact) that the quality system guarantees the conformity of the pyrotechnic
the product with the type which has been assessed the conformity assessment procedures of the EU
type-examination,
(b)) the business name and address of the registered office or the name, surname and the address of the place of residence
the manufacturer,
(c)) the business name and address or name, surname and the address of the place of residence
the importer in the case of import of the pyrotechnic article,
d) data necessary to identify the approved quality system, the holder of the
of the certificate and of the notified body which issued the certificate,
(e)) the conclusions of conformity assessment and
(f)) for its validity.
§ 8
The pattern of the EU Declaration of conformity
The pattern of the EU Declaration of conformity is given in annex 2 to this regulation.
§ 9
The effectiveness of the
This Regulation shall enter into force on the fifteenth day following its publication.
The President of the Government:
MSC. in r. Sobotka.
Minister of industry and trade:
Ing. Mládek, CSc., r.
Annex 1
CONFORMITY ASSESSMENT PROCEDURES
1. the EU type-examination (module B)
1.1 EU type examination is the part of a conformity assessment procedure, in which
the notified body shall examine the technical design of the pyrotechnic article and
verifies that the technical design meets the requirements of the pyrotechnic article
the law.
1.2 the EU type-examination shall be carried out in order to assess the suitability of the
the technical design of the product through examination of the bomb
the technical documentation and supporting evidence, and the examination of a sample of the complete
the product which corresponds to the planned product (combination of production type and
the type of design).
1.3. The notified body must examine the pyrotechnic article technical
documentation and supporting evidence to assess the adequacy of the technical
the design of the pyrotechnic article.
1.4 the notified body for a sample of
1.4.1 examine whether the sample was made in accordance with the technical
documentation and identify the elements which have been designed in accordance with the applicable
the provisions of harmonised standards and elements which have been designed in
comply with other technical specifications;
1.4.2 perform or have carried out the examination and tests to verify whether the
in the case where the manufacturer has chosen the solution in accordance with harmonised standards,
These standards are used correctly;
1.4.3. carry out or have carried out the examination and tests to verify whether the
in the case where the solution has been applied in accordance with the harmonised standards,
solutions that meet the manufacturer, including used other
technical specifications corresponding to the basic safety requirements
the law;
1.4.4 shall agree with the manufacturer, at which point they will review and
the tests carried out.
1.5 If the type meets the requirements of the Act, which apply to the
the pyrotechnic article, the notified body shall issue a certificate to the manufacturer of the EU
type-examination.
If the type does not satisfy the requirements of the Act, the notified body shall issue the certificate
the EU type-examination certificate and shall inform the applicant, and
no need to justify to the certificate.
1. The notified body 6 tracks changes to generally recognized scientific
knowledge, on the basis of which it would already have been type-approved in accordance
with the requirements of the law, and if such changes require deeper investigation,
shall inform the manufacturer.
The manufacturer shall inform the notified body that holds the technical
the documentation concerning the EU type-examination certificate of all
adjustments to the approved type that may affect the conformity of the pyrotechnic
the product with the essential safety requirements of the law or the conditions of
the validity of this certificate. These customizations require additional approval
in the form of a supplement to the original EU type-examination certificate.
1. The notified body shall inform its 7 notifying authorities about certificates
The EU type-examination or additions thereto which it has issued or withdrawn, and
regularly or on request, make available to its notifying authorities the list of
These certificates, or amendments thereto, which he refused, suspended or
otherwise restricted.
The notified body shall inform the other notified bodies of the EU certificates
type-examination or the appendices thereto, which he refused, withdrawn,
suspended or otherwise restricted, and, upon request of
certificates or additions thereto which it has issued.
The notified body shall provide to the Commission, the Member States or other
notified bodies, on request, a copy of the EU type-examination certificate
type or amendments thereto. The notified body shall provide to the Commission or the Member
States at their request, a copy of the technical documentation and the results of the
the examination, which he did. To the expiry of the period of validity of the certificate of the EU
type-examination, the notified body shall retain a copy of this certificate,
its annexes and appendices, as well as the technical file including the
the documentation submitted by the manufacturer.
1. the manufacturer must, for 8 national authorities according to § 18
paragraph. 4 dossier, which act in the EU type-examination consists of a copy of the
the EU type-examination certificate, its annexes and appendices.
2. Conformity to type based on internal production control and tests
under the supervision of the product at random intervals (module C2)
2.1 assessment of conformity to type based on internal production control and
the product under the supervision of tests at random intervals is the part
the conformity assessment procedure, that the manufacturer fulfils the obligations laid down in
points 2.2, 2.3 and 2.4, and on their own responsibility declares that the
pyrotechnic articles are in conformity with the type as described in the certificate of the EU
type-examination and meet the requirements of the Act.
2.2 Production
The manufacturer shall take measures in order that the manufacturing process and its control
ensure conformity of the manufactured pyrotechnic articles with the type described in the
the EU type-examination certificate and with the requirements of the Act.
2.3 Test product
The notified body chosen by the manufacturer carries out the test product or allow
such tests to be carried out at random intervals, which itself
lays down, in order to verify the quality of the internal tests of pyrotechnic
the product, taking into account inter alia the technological complexity of
pyrotechnic products and the quantity produced. Before placing on the market
Removes the notified body on the spot an adequate sample of the final
the products, which must be examined and appropriate tests
laid down in harmonised standards, or equivalent tests referred to
in other technical specifications, in order to verify the conformity of the
a pyrotechnic product with the type as described in the EU type-examination certificate
the type and the requirements of the Act. If the sample does not reach an acceptable level of
the quality, the notified body shall take the necessary measures.
Sampling procedure for the purpose of acceptance has to verify that the manufacturing process
the pyrotechnic article is within acceptable limits to ensure
the conformity of the pyrotechnic article.
The manufacturer must affix the products during the manufacturing process on the responsibility
the notified body's identification number to the relevant notified
the body.
2.4. CE marking and Declaration of conformity EU
2.4.1. The manufacturer of the affix the CE marking to each individual pyrotechnical
a product that is in conformity with the type as described in the certificate of the EU
type-examination and satisfies the requirements of the Act.
2.4.2. The manufacturer shall establish for each product model written EU Declaration of
conformity. In the EU Declaration of conformity is given the pyrotechnic article,
which it was drawn up.
A copy of the EU Declaration of conformity the manufacturer shall provide, on request, to the competent
the inspection authorities.
3. Conformity to type based on quality assurance of the production process
(module D)
3.1 the assessment of conformity to type based on quality assurance of the
the process is part of a conformity assessment procedure, that the manufacturer fulfils the
the obligations laid down in points 3.2 and 3.5, and on their own responsibility
declares that the pyrotechnic articles are in conformity with the type
as described in the EU type-examination certificate and satisfy the requirements of the Act.
3.2 Production
The manufacturer must operate an approved quality system for production, final inspection
and tests of pyrotechnic articles concerned referred to in section 3.3 and subject to
the surveillance referred to in point 3.4.
3.3. Quality System
3.3.1. The notified body shall assess the quality system meets the requirements of
laid down by law.
The elements of the quality system which conform to the provisions of the harmonised
standards, the notified body, the conformity with these requirements. Of the person,
that the name of the notified body carrying out the assessment of the quality system,
(hereinafter referred to as the "audit team") must have experience with systems management
the quality and knowledge of the requirements of the Act and at least one Member must have
experience with the assessment of the relevant products and with the relevant
technology product. The audit includes an evaluation visit in the operating
the premises of the manufacturer. The audit team shall review the technical documentation,
to verify that the manufacturer shall proceed according to the requirements of the Act for the given type
conformity assessment and conducts all the necessary examination, in order to guarantee
the conformity of the pyrotechnic article with these requirements.
The conclusions of the audit, including the reasons therefor shall be notified to the manufacturer.
3.3.2. the Producer is obliged to fulfil the obligations arising from the approved
of the quality system and to maintain it so that it remains adequate and efficient.
3.3.3. The manufacturer may change the quality system, which was developed
the quality system documentation, only with the prior consent of the notified
the body.
The notified body must assess the changes proposed and whether the modified quality system
It will continue to comply with the same requirements as the existing quality system
or whether it should be a new assessment.
The notified body shall inform its assessment, including its rationale, producers.
3.4. Surveillance under the responsibility of the notified body
3.4.1. The purpose of surveillance is to ensure that the manufacturer duly fulfils the obligations
arising out of the approved quality system.
3.4.2 in order to exercise supervision, the manufacturer must allow the notified body
access to the places of manufacture, inspection, testing and storage
and provide it with all the necessary documents, in particular the
and) the quality system documentation;
(b)) the quality records, in particular the reports of the inspections, the records of the
tests carried out, records of the performed calibration and reports on
the qualifications of the persons responsible for the assessment of conformity.
3.4.3. The notified body must periodically carry out audits to verify whether the
manufacturer maintains and applies the quality system and to submit a report on the
the audit.
3.4.4. The notified body may carry out the manufacturer of control and without
prior notice. Under the control of a notified body in the case of
necessary to perform, or have performed, the test of products, in order to verify whether the
the quality system is functioning correctly. The notified body must provide the manufacturer
a report on the inspection and test, if the test was performed.
3.5 the CE marking and the EU Declaration of conformity
3.5.1 Manufacturer affix the CE marking to each individual pyrotechnical
a product that is in conformity with the type as described in the certificate of the EU
type-examination and satisfies the requirements of the law, and on the responsibility of
the notified body, that submitted an application for assessment of conformity with the type
based on quality assurance of the production process, connect
the identification number of the notified body.
3.5.2. The manufacturer shall establish for each product model written EU Declaration of
conformity. In the EU Declaration of conformity is given the pyrotechnic article,
which it was drawn up.
A copy of the EU Declaration of conformity the manufacturer shall provide, on request, to the competent
the inspection authorities.
3.6 the manufacturer shall keep available for the national authorities according to § 18 paragraph.
4 dossier, which act in conformity to type based on security
the quality of the manufacturing process consists of:
and approved the change information) of the quality system,
(b)) the conclusions of the examination and the reasoned assessment decision, reports and
the protocols of the notified body referred to in point 3.4.3 and 3.4.4.
3.7. The notified body shall inform its notifying authorities about the issued or
cancelled the quality system approvals and regularly or on request
make available to its notifying authorities the list of quality system approvals
that was refused, suspended or otherwise restricted.
The notified body shall inform the other notified bodies of the approvals
quality system, which rejected, suspended, cancelled or otherwise restricted, and
on the application of the quality system approvals which it has issued.
4. Conformity to type based on product quality assurance (module E)
4.1 assessment of conformity to type based on quality assurance of the product is
part of the conformity assessment procedure, that the manufacturer fulfils the obligations laid down
in points 4.2 and 4.5, and on their own responsibility declares that the
pyrotechnic articles are in conformity with the type as described in the certificate of the EU
type-examination and meet the requirements of the Act.
4.2 Production
The manufacturer must operate an approved quality system for final inspection and
tests of pyrotechnic articles concerned as specified in point 4.3, and shall be subject to
surveillance as specified in point 4.4.
4.3. Quality System
4.3.1. The notified body shall assess the quality system meets the requirements of
laid down by law.
The elements of the quality system which conform to the harmonised
standards, the notified body, the conformity with these requirements.
The audit team must have experience with the quality management systems and knowledge
the requirements of the Act and at least one Member must have experience with
the evaluation of the relevant products and product technologies. Audit
includes the assessment visit to the manufacturer's premises.
The audit team shall review the technical documentation to verify that the manufacturer
in accordance with the requirements of the Act for the type of conformity assessment and performs
the necessary examination, in order to guarantee compliance with the pyrotechnic article
These requirements.
The conclusions of the audit, including the reasons therefor shall be notified to the manufacturer.
4.3.2. The manufacturer is obliged to fulfil the obligations arising from the approved
of the quality system and to maintain it so that it remains adequate and efficient.
4.3.3. The manufacturer may change the quality system, which was developed
the quality system documentation, only with the prior consent of the notified
the body.
The notified body must assess the changes proposed and whether the modified quality system
It will continue to comply with the same requirements as the existing quality system
or whether it should be a new assessment.
The notified body shall inform its assessment, including its rationale, producers.
4.4 Monitoring under the responsibility of the notified body
4.4.1. The purpose of surveillance is to ensure that the manufacturer duly fulfils the obligations
arising out of the approved quality system.
4.4.2. For the purpose of exercising supervision, the manufacturer must allow the notified body
access to the places of manufacture, inspection, testing and storage
and provide it with all the necessary documents, in particular the
and) the quality system documentation;
(b)) the quality records, in particular the reports of the inspections, the records of the
tests carried out, records of the performed calibration and reports on
the qualifications of the persons responsible for the assessment of conformity.
4.4.3. The notified body must periodically carry out audits to verify whether the
manufacturer maintains and applies the quality system and to submit a report on the
the audit.
4.4.4. the notified body may carry out without checking the manufacturer
prior notice. Under the control of a notified body in the case of
necessary, carry out or have carried out product test, to verify whether the
the quality system is functioning correctly. The notified body must provide the manufacturer
a report on the inspection and test, if the test was performed.
4.5 the CE marking and the EU Declaration of conformity
4.5.1 Manufacturer affix the CE marking to each individual pyrotechnical
a product that is in conformity with the type as described in the certificate of the EU
type-examination and satisfies the requirements of the law, and on the responsibility of
the notified body, that submitted an application for assessment of conformity with the type
based on the quality of the product, attach the identification number
of the notified body.
4.5.2. The manufacturer shall establish for each product model written EU Declaration of
conformity. In the EU Declaration of conformity is given the pyrotechnic article,
which it was drawn up. A copy of the EU Declaration of conformity the manufacturer upon request
shall provide to the competent control authorities.
4.6. The manufacturer shall keep available for the national authorities according to § 18 paragraph.
4 dossier, which act in conformity to type based on security
the quality of the product consists of:
and approved the change information) of the quality system,
(b)) the conclusions of the examination and the reasoned assessment decision, reports and
the protocols of the notified body referred to in point 4.4.3 and 4.4.4.
4.7. The notified body shall inform its notifying authorities about the issued or
cancelled the quality system approvals and regularly or on request
make available to its notifying authorities the list of quality system approvals
that was refused, suspended or otherwise restricted. The notified body
It shall inform the other notified bodies of quality system approvals
which dismissed, suspended or canceled, and at the request of the approvals system
the quality which it has issued.
5. conformity based on unit verification (module G)
5.1. Assessment of conformity based on unit verification
is the conformity assessment procedure whereby the manufacturer fulfils the obligation to draw up and
pass the technical documentation the notified body and the obligations
set out in sections 5.2 and 5.4, and on their own responsibility declares that
the pyrotechnic article, which has been verified in accordance with section 5.3, the
conformity with the requirements of the Act.
5.2 Production
The manufacturer shall take measures in order that the manufacturing process and its control
ensure conformity of the manufactured product with the requirements of the bomb
the law.
5.3 the verification
A notified body chosen by the manufacturer, shall carry out or have carried out
examinations and tests specified in the harmonised standards, or
equivalent to the tests referred to in other technical specifications to
Verify the conformity of the pyrotechnic article with the requirements of the Act. If such
There is no harmonised standard, the notified body concerned shall decide which
the tests are to be carried out.
The notified body shall issue a certificate of conformity with regard to the carried out
examination and tests and approved pyrotechnic article on your own
responsibility shall affix or allow to affix its identification number.
5.4 the CE marking and the EU Declaration of conformity
5.4.1 the manufacturer to affix the CE marking to each pyrotechnic article,
meets the requirements of the law, and on the responsibility of the notified body
referred to in point 5.3 connect the identification number of the body.
5.4.2. The manufacturer shall draw up a written declaration of conformity to the EU. In the EU Declaration
on the conformity of the pyrotechnic article is mentioned, for which it was drawn up.
A copy of the EU Declaration of conformity the manufacturer shall provide, on request, to the competent
the inspection authorities.
5.5. the Manufacturer shall keep available for the national authorities according to § 18 paragraph.
4 of the Act, which in the case of conformity documentation based on verification
the unit consists of a certificate of conformity.
6. the conformity based on comprehensive quality assurance (module H)
6.1. Conformity assessment based on comprehensive quality assurance is
the conformity assessment procedure whereby the manufacturer fulfils the obligations laid down in
paragraphs 6.2 and 6.5 and on their own responsibility declares that the
pyrotechnic products meet the requirements of the Act.
6.2 Production
6.2.1. The manufacturer must operate an approved quality system for design, manufacture,
final inspection and testing of pyrotechnic articles concerned by
6.3.
6.2.2 the manufacturer is subject to supervision in accordance with point 6.4.
6.3 the quality system
6.3.1. The notified body shall assess the quality system meets the requirements of
laid down by law.
The elements of the quality system which conform to the harmonised
standards, the notified body, the conformity with these requirements.
The audit team must have experience with the quality management systems and knowledge
the requirements of the Act and at least one Member must have experience with
the evaluation of the relevant products and the relevant technology of the product.
The audit includes an assessment visit to the manufacturer's premises.
The audit team shall review the technical documentation to verify that the manufacturer
in accordance with the requirements of the Act for the type of conformity assessment and performs
all the necessary examinations, in order to guarantee the consistency of the pyrotechnic
of the product with these requirements.
The conclusions of the audit, including the reasons therefor shall be notified to the manufacturer.
6.3.2. The producer is obliged to fulfil the obligations arising from the approved
of the quality system and to maintain it so that it remains adequate and efficient.
6.3.3. The manufacturer may change the quality system, which was developed
the quality system documentation, only with the prior consent of the notified
the body.
The notified body must assess the changes proposed and whether the modified quality system
It will continue to comply with the same requirements as the existing quality system
or whether it should be a new assessment.
The notified body shall inform its assessment, including its rationale, producers.
6.4 Monitoring under the responsibility of the notified body
6.4.1 the purpose of supervision is to ensure that the manufacturer duly fulfils the obligations
arising out of the approved quality system.
6.4.2 for the purposes of exercising supervision, the manufacturer must allow the notified body
access to the places of design, manufacture, inspection, testing and
storage and shall provide it with all the necessary documents, in particular the
and) the quality system documentation;
(b)) the quality records provided for in part of the quality system relating to
the proposal, in particular the results of analyses, calculations and tests;
(c)) the quality records provided for in the manufacturing part of the quality system, in particular the
reports of inspections, the records of the tests carried out, the records of the
the calibration carried out and reports on the qualifications of the persons responsible for the
assessment of conformity.
6.4.3. The notified body must periodically carry out audits to verify whether the
manufacturer maintains and applies the quality system and to submit a report on the
the audit.
6.4.4. the notified body may carry out without checking the manufacturer
prior notice. Under the control of a notified body in the case of
necessary to perform, or have performed, the test of products, in order to verify whether the
the quality system is functioning correctly. The notified body must provide the manufacturer
a report on the inspection and test, if the test was performed.
6.5 the CE marking and the EU Declaration of conformity
6.5.1 Manufacturer affix the CE marking to each individual pyrotechnical
a product that meets the requirements of the law, and on the responsibility of a notified
the body, which has submitted an application for conformity assessment based on
comprehensive quality assurance, attach an identification number of this
of the notified body.
6.5.2 manufacturer for each product model written EU Declaration of
conformity. In the EU Declaration of conformity is given the pyrotechnic article,
which it was drawn up.
A copy of the EU Declaration of conformity the manufacturer shall provide, on request, to the competent
the inspection authorities.
4.1 the manufacturer shall keep available for the national authorities according to § 18 paragraph.
4 of the Act, which in the case of conformity documentation based on comprehensive security
the quality of the form:
and approved the change information) of the quality system,
(b)) the conclusions of the examination and the reasoned assessment decision, reports and
the protocols of the notified body referred to in point 6.4.3 and 6.4.4.
4.2. the notified body shall inform its notifying authorities about the issued or
cancelled the quality system approvals and regularly or on request
make available to its notifying authorities the list of quality system approvals
that was refused, suspended or otherwise restricted. The notified body
It shall inform the other notified bodies of quality system approvals
which dismissed, suspended or canceled, and at the request of the approvals system
the quality which it has issued.
Annex 2
Pattern
EU Declaration of conformity (no XXXX) 1)
1. Registration number2):
2. The product number, lot or series:
3. Trade name and address or name, surname and residence address of the manufacturer:
4. this Declaration of conformity is issued under the sole responsibility of the manufacturer.
5. The subject of the Declaration (identification of product allowing it to trace):
6. the subject of the Declaration described above is in conformity with the legislation of the Union placed:
7. the references to the harmonised standards used, or references to other technical
the specification on the basis of conformity declares:
8. The notified body-(name, number) ... carried out ... (description of intervention)..., and vydalcertifikát:
9. Additional information:
Signed for and on behalf of:
(place and date of issue):
(name, function) (signature):
_________________________________
1) numeric indication of the EU conformity declaration is optional. It is a custom of numbering the EU Declaration
of conformity, which can give the EU Declaration of conformity the manufacturer himself.
2) Article. 9 directive of the European Parliament and of the Council of 13/29/EU of 12 June. June 2013 on the harmonisation
the legislation of the Member States relating to the supply of pyrotechnic articles on the market.
1) directive of the European Parliament and of the Council of 13/29/EU of 12 June. June
2013 on the harmonisation of the laws of the Member States relating to the
the supply of pyrotechnic articles on the market.
