(December 31, 2002 the State General Administration of quality supervision, inspection and quarantine announced, 36th) Chapter I General provisions article in order to strengthen the management of state metrological and guarantee unification of units of measurement and measuring instruments measure accurately, in accordance with the People's Republic of China metrology and the People's Republic of China metrology rules for the implementation of the relevant provisions, these measures are formulated.     Second national metrological means by the State General Administration of quality supervision, inspection and quarantine (hereinafter referred to as AQSIQ) developed and approved for publication, implementation in the country, as a characteristic evaluation of measuring instruments and legal management of metrology technology regulations.     Article develop, revise, approve and publish, review national verification procedures, which must comply with these measures.     Article fourth national verification procedures should comply with the relevant national legal provisions and regulations; scope must be clearly defined, within its defined scope, seeks to complete; the requirements of scientific and reasonable, taking into account the feasibility and the economic efficiency of the operation.     Fifth article released by the active use of the international organization of legal metrology international recommendations, international standards issued by the international instruments and relevant international organizations; in use shall be in accordance with relevant regulations and policies of the State, staying active and pragmatic approach.     Sixth national verification procedures by the State administration of quality supervision plan, coordination Division, Organization (including amendments, the same below), review, number, release.     Chapter II plans seventh of national metrological verification regulation preparation of national metrological projects should be based on economic and science and technology development and rule of law supervision and management as the basis of measurement.     Eighth AQSIQ in next April each year an annual national metrological program principles, given to the National Commission for professional measurement technology (hereinafter "Technical Committee").     Nineth Technical Committee according to the principle of the preparation of national metrological requirements in August of that year and prospectus of the draft plan by the end of the project (see annex 1) reported that the State General Administration of quality supervision.     Tenth AQSIQ on the draft national metrological program reported consolidated summary, review, coordination, and in December of that year before the approval issued by the national metrological program next year.     11th article the Technology Committee in implementation national measurement verification procedures plans process in the, has following situation Shi can on plans project for adjustment: (a) does is needed developed national measurement verification procedures of project, can added; (ii) does is should not be developed national measurement verification procedures of project, should to undo; (three) does is special situation, can on plans project content for adjustment. 12th National metrological projects should be completed by a responsible for the draft "national metrological program project application form" (see annex 2), after approval by the responsible Technical Committee, reported that the State General Administration of quality supervision and approval. Adjustment of the AQSIQ approval, apply adjustments shall be notified to the relevant technical Committee.     Adjustment of national metrological program project application has been approved, the relevant technical committees must work according to the original plan.     Chapter III national metrological 13th section technical committees under the AQSIQ approval issued by the national metrological program to organize and guide the drafting work, supervise the work progress, checking completed tasks.     14th article drafting units should according to national measurement verification procedures prepared guide is effective version of requirements, in investigation, and test validation of based Shang, proposed national measurement verification procedures sought views draft, and "prepared description", about annex, distributed this technology Committee the members, and communications units members, and about manufacturing enterprise, and provincial measurement administration sector, and measurement verification institutions, and using units, and related standard of drafting units or personal widely sought views. 15th annex shall include the following information: (a) preparation of notes. Stated task source, and prepared according to, and and "International recommends", and "international file", and "international standards", and domestic standard, technology file of compatible situation, on by provides of some technology terms, and verification conditions, and verification method of about description, on major differences views of processing results and according to,; in Amendment Shi, should on new, and old national measurement verification procedures of modified content be description,; (ii) test report. National metrological measurement performance, set out in the technical specifications, should be using prescribed test conditions, test method applicable to the scope of object detection, using test data to prove its viability; (c) error analysis. Application of error theory analysis and uncertainty evaluation method under the metrological requirements, technical requirements, test conditions (the standard devices and related equipment, environmental conditions), the test method is scientific and rational.     Should also be listed in error, error type, synthesis methods and confidence probability, and (d) adoption of international recommendations, international and Chinese translations of the original file or international standards.     National metrological verification regulation of 16th article draft for a period of 2 months. Consultation responses within a unit or individual shall, within the prescribed period if not reply comments should also be stated; fails to reply, press no objection handling.     If there are more significant, it shall explain the reasons and the test data.     17th drafter or drafting comments were received after the analysis, opinion and disposition of content results are listed, form "request for comments summary" (see annex 3).     18th drafting units according to request for comments summary of draft amendments proposed national metrological examination and the written notes, test reports, error analysis, request for comments summary sheets, the international recommendations and international documents or original text and Chinese translation of international standards relating to attachment, send review by the Secretariat of the Technical Committee.     19th Technical Committee secretariat in accordance with the provisions of the Statute of the national technical Committee of professional metrology procedures and organization review draft of the review. High technical content and covers a wide range, the differences are many national verification procedures, in order to ensure the quality of its writing, validation of the Conference mainly content than a single, smaller differences of functions can be carried out.     Specific validation form decided by the Technical Committee.     Technical secretariat of the Committee should be in triage or to you 1 month before the trial, the state metrological examination draft and submit the relevant annex approved by. 20th Conference review article should, in principle, agreed.     If you want to vote (in favour, against or abstain from voting) votes, at least should get more than enough to three-fourths the number of members in favour of the passage, and written materials record, drafters could not participate in the voting.     If any member of the communications unit, the Special Representative attended the meeting, it should be on record.     You must have three-fourths replies in favour of the passage.     Review must have "validated submissions" (see annex 4), validation comments should be adopted by the delegates; letter must be attached to each letter of Auditor's letter (see annex 5) and summary of audited views of the trial, which includes assessment of the procedures and the main amendments (see annex 6). The 21st National metrological verification regulation of registered, by drafting units according to the audited opinions collated form approval. Approval and the provision of related Technical Committee secretariat review report information. Content of national metrological approval should be consistent with the review of authorized content. As technology changes, should be "written description" in the description.     Submitted file including: (a) approval national measurement verification procedures of documents 1 copies (format see annex 7); (ii) national measurement verification procedures approval draft 2 copies, floppy disk 1 copies; (three) national measurement verification procedures approval table (format see annex 8), and prepared description, and test report, and errors analysis, and sought views summary table, and validation submissions, and international recommends, and international file or international standards of original and Chinese translations and the other about material the 1 copies.     Technical secretariat of the Commission to review the submitted materials and in "approval form" signed, after all the materials submitted to the state metrological review Department for review.     The fourth chapter of national metrological approval, publishing articles 22nd National metrological centrally by the AQSIQ approval (approval form is shown in Appendix 8), numbering, in the form of announcement.     Number of the 23rd national metrological verification regulation by its code name, sequence number, and publication year composition.     National metrological code-named "JJG".     The 24th national metrological process relevant information should be archived. 25th National metrological verification regulation is published, by the AQSIQ to publishing.     In the process of publishing, when doubts and errors are spotted, publishers should get in touch with relevant technical committees if technical content when you need to change should be approved by the State administration of quality supervision, drafting may not change the content of national metrological.     National metrological verification regulation of the need to be translated into foreign languages, organized by the Technical Committee charged with developing its translation translation and validation, and published by the publishing unit of the national metrological.     26th article national measurement verification procedures published Hou, found individual technology content has problem, must do few modified or added Shi, by drafting people fill in "modified national measurement verification procedures declared table" (format see annex 9), by related of Technology Committee audit agreed, to file form (format see annex 10) and attached "modified national measurement verification procedures declared table" 2 copies, reported procedures approval units approved, and to announcement form released.     Fifth chapter review the 27th State of the national metrological verification regulation after the implementation of release should be based on the development of science and technology and economic construction and supervision and administration of legal metrology needs and timely review by the relevant technical Committee plan, review period does not normally exceed 5 years.     National metrological review can be used to review or examination by letter, original drafters to participate. 28th National metrological verification regulation of the review in accordance with the following circumstances: (a) do not need to modify the national verification procedures, confirmation remain valid. Recognizes the continuing effective national verification procedures do not change the order number and the name. When reprinted, in its cover, national metrological verification Regulation number write "XXXX year validated"; (ii) the national metrological modifications required, as the amendments included in the plan.     Amendment of the national metrological order unchanged, name changed to revised title; (c) is not subject to national metrological verification of measuring instruments, abolish it.     29th national metrological review upon completion of the review of the Technical Committee shall write a review report, including: review profiles, comments, review findings reported to the approval of the State administration of quality supervision, and publish it in the form of announcement.     30th national metrological verification regulation belongs to the scientific and technological achievements should be incorporated into national or sectoral scope of science and technology progress award, shall be awarded. Sixth chapter supplementary articles article 31st of any units or individuals, without the approval of the State administration of quality supervision, are not free to change national metrological verification regulation.     Violations of these rules shall be directly responsible for criticism, education, administrative sanctions, criminal responsibility shall be investigated according to law.     32nd article this approach by the AQSIQ to interpret. 33rd article this way come into effect on February 1, 2003.       Former State Bureau of technical supervision released on August 5, 1991 on revision of national metrological regulations shall be void. Appendix 1: description of regulations project task book is introducing, revising an important basis for national technical regulations.       In order to unify format and easy to archive, mainly drafting unit in the prospectus format and content requirements to fill out. Annex 2: national metrological program project application form Annex 3: consultation summary table annex 4: Annex 5 Annex 6 Annex 7: approval document format of the national metrological Annex 8: Annex 9 Annex 10: submitted to the state metrological modification document format