Advanced Search

Plastic Regulation

Original Language Title: Kunststoffverordnung

Subscribe to a Global-Regulation Premium Membership Today!

Key Benefits:

Subscribe Now for only USD$40 per month.

242. Regulation of the Federal Minister for Health and Women amending the Plastic Regulation 2003

On the basis of Articles 29 and 30(2). 1 of the Food Law 1975, BGBl. No 86, last amended by the Federal Law BGBl. I No. 126/2004, is prescribed:

The Plastic Regulation 2003, BGBl. II No. 476/2003, is amended as follows:

1. The following sentence is added to § 4(1):

"The Annex 2 does not yet introduce additives that are used only for the production of surface coatings from liquid, powdered or dispersed resins or polymers such as paints or paints, as well as epoxy resins, adhesives and prison intermediaries or printing colours. There are no additives used as colours or solvents. “

2. § 4(2). 2 is:

"(2) The additives referred to in Annex 2, Section B shall be subject to the specific migration values from 1. July 2006, provided that the verification of compliance with simulate proceeding D or with test media is carried out by replacement checks according to the facilities 6 to 8. “

3. The § 4 is the following paragraph. 3 added:

"(3) Additives of Annex 2, which are authorised as food additives or flavourings, must not be exceeded

1.

in food or food supplements in quantities that have a technological effect in the food end product;

2.

in food or food supplements for which their use is authorised as food additives or flavourings, in quantities exceeding the limit values laid down or set in Annex 2, while respecting the lowest limit;

3.

in food or food supplements for which their use as food additives or flavourings is not permitted, in quantities exceeding the limit values set in Annex 2. “

4. Under § 8, the following § 8a and heading is inserted:

"Conformity Statement

§ 8a. (1) Plastic items must be accompanied by a written declaration at all marketing stages, except in retail, which will certify that they conform to the rules applicable to them. This declaration is to be issued by the manufacturer or by a distributor established in the European Community.

(2) The written declaration in accordance with paragraph 1 also has to provide adequate information on the specific migration values and, where appropriate, purity criteria, which are included in the respective versions, of the sweetener Regulation (BGBl) No 541/1996, in the respective versions, of the relevant Regulation (BGBl. No. 547/1996), in the current version, of the relevant Regulation (BGBl. No. 547/1996), in the respective version, or the ZuV, BGBl. II 383/1998, in each of the current version. “

5. § 9(2). 2 Z 1 is:

"1.

Evidence from the determination of the total migration limit values shows that according to paragraph. 1 specific migration limits to be determined shall not be exceeded or"

6. § 11 is:

" § 11. (1) Plastic items not covered by Regulation BGBl. II No 242/2005, but comply with the provisions previously in force, with the exception of paragraph No. 2, may still be until 28. which will be placed on the market by the end of February 2006.

(2) Plastic items not covered by Regulation BGBl. II No 242/2005, but to the extent that it relates to the substance of the reference number 36640 of Annex 2, Section A, and before 2. Once the expiry date is indicated on them, it may be placed on the market. The date of filling may be replaced by a different indication, if this allows for the identification of the date of filling. On demand, the date of filling is to be announced as a competent authority in accordance with Section 35 LMG 1975. The Food Labelling Regulation 1993 - LMKV, BGBl. No 72/1993, in the respective version, must be observed. “

7. The following Directives are added to § 12:

"- 2004/1/EC of the Commission amending Directive 2002/72/EC on the suspension of the use of Azodicarbonamid as a drift (OJ L 7, 13. January 2004),

- 2004/19/EC of the Commission amending Directive 2002/72/EC on plastic materials and objects intended to come into contact with food (OJ L 71, 10 March 2004). “

8. In Annex 1 General Introduction Z 8, the definition of QM is as follows:

"QM = maximum permitted residual content of the substance in the material or object. In the sense of this Directive, the quantity of substance contained in the material or object is to be determined by measuring a validated analytical method. If there is currently no such method, an analytical method can be applied with appropriate sensitivity that allows the determination of the specified limit until a validated method has been developed;"

9. In Annex 1 General Introduction Z 8, the word in the definitions of QMA and QMA(T) "Consumption products" by the word "food supplements" replaced.

10. Annex 1 General Introduction Z 9 Lithuania.a is:

"a)

retention or retention-like or other refillable items with a capacity of less than 500 millilitres or more than 10 litres; “

11. In Annex 1, Section A, the following monomers and other raw materials are inserted in corresponding numerical order:

Ref. No.

CAS No.

Name

Restrictions and/or specifications

(1)

(2)

(3)

(4)

"13323

16540

18896

20440

22775

23070

000102-40-9

000102-09-0

001679-51-2

000097-90-5

000144-62-7

000102-39-6

1.3-Bis(2-hydroxyethoxy)benzol

Diphenyl carbonate

4-(Hydroxymethyl)-1-cyclohexen

Ethylenglykoldimethacrylate

Oxalic acid

(1.3-Phenylendioxy) acetic acid

SML = 0.05 mg/kg

SML = 0.05 mg/kg

SML = 0.05 mg/kg

SML = 0.05 mg/kg

SML(T) = 6 mg/kg (29)

QMA = 0.05 mg/6 dm2

12. For the following monomers and other raw materials listed in Annex 1, Section A, the contents of the column "Signature" or “CAS No”. or "Restrictions and/or specifications" as follows:

Ref. No.

CAS No.

Name

Restrictions and/or specifications

(1)

(2)

(3)

(4)

"11530

13480

14950

18898

22150

22331

22332

24190

00999-61-1

000080-05-7

003173-53-3

000103-90-2

000691-37-2

025513-64-8

065997-05-9

2-Hydroxypropylacrylate

2.2-Bis(4-hydroxyphenyl)

perpan

Cyclohexylisocyanat

N-(4-Hydroxyphenyl)acetamid

4-Methyl-1 pens

mixture of (35-45 Gew-%) 1.6-Diamino-2,4-trimethylhexan and (55-65 Gew-%) 1.6-Diamino-2,4,4-trimethylhexanxan

Mix of (40%) 2.2.4-Trimethylhexan-1.6-Diisocyanat and (60%) 2.4.4-Trimethylhexan-1.6-Diisocyanat

tree resins"

QMA = 0.05 mg/6 dm2 for the sum of 2-Hydroxypropyl-acrylate and 2-Hydroxyisopropyl-acrylate and according to the specifications set out in Annex 4

SML(T) = 0.6 mg/kg (T)28)

QM(T) = 1 mg/kg in BG (calculated as NCO)26)

SML = 0.05 mg/kg

SML = 0.05 mg/kg

QMA = 5 mg/6 dm2

QM(T) = 1 mg/kg (calculated as NCO)26)

13. The following monomers and other raw materials are removed from Annex 1, Section B and inserted in Annex 1, Section A in corresponding numerical order:

Ref. No.

CAS No.

Name

Restrictions and/or specifications

(1)

(2)

(3)

(4)

"10599/90A

10599/91

10599/92A

10599/93

14800

16210

17110

18700

21400

061788-89-4

061788-89-4

068783-41-5

068783-41-5

003724-65-0

006864-37-5

016219-75-3

000629-11-8

054276-35-6

Dimers of unsaturated fatty acids (C18), distillation

Dimers of unsaturated fatty acids (C18), not distilled

Dimere, of unsaturated fatty acids (C18), hydrated, distilled

Dimere, of unsaturated fatty acids (C18), hydrated, not distilled

Crotonic acid

3,3'-dimethyl-4,4'-diaminodicyclohexylmethane

5-Ethylidenbicyclo(2.2.1)hept-2

1.6-Hexandiol

Sulfopropylmethacrylate

QMA(T) = 0.05 mg/6 dm2 (b)27)

QMA(T) = 0.05 mg/6 dm2 (b)27)

QMA(T) = 0.05 mg/6 dm2 (b)27)

QMA(T) = 0.05 mg/6 dm2 (b)27)

QMA(T) = 0.05 mg/6 dm2 (b)33)

SML = 0.05 mg/kg (32). Use only in polyamides

QMA = 0.05 mg/6 dm2. The ratio of surface to food quantity must be less than 2 dm2/kg

SML = 0.05 mg/kg

QMA = 0.05 mg/6 dm2

14. The following monomers and other raw materials are removed from Annex 1, Section A:

Ref. No.

CAS No.

Name

Restrictions and/or specifications

(1)

(2)

(3)

(4)

"15370

15400

003236-53-1

003236-54-2

1.6-Diamino-2,2,4-Trimethyl-hexan

1.6-Diamino-2,4,4-Trimethyl-hexan

QMA = 5 mg/6 dm2

QMA = 5 mg/6 dm2

15. Annex 2 General Introduction Z 1 is as follows:

"1.

This plant contains the list of:

(a)

Substances that are added to plastic to achieve a technical effect in the final product, including polymer additives. These substances are intended to be present in the final product;

(b)

Substances used to form an appropriate medium in which polymerisation takes place.

The substances referred to in (a) and (b) are referred to below as additive.

In the sense of this facility, polymers, polymers and/or prepolymers and/or oligomers are called to use plastics to achieve a technical effect but cannot be used alone without other polymers as the main structural part of the final product. These include substances that can be added to the medium in which polymerisation takes place.

Not covered

(a)

substances that directly influence the formation of polymers;

(b)

colours;

(c)

solvent. “

16. The Annex 2 General Introduction is added to the following 8:

"8.

The SML values listed in column 4 are indicated in milligrams per kilogram (mg/kg). However, in the following cases, the values must be calculated in milligrams per square metering (for conversion, the SML values specified in milligrams per kilogram are divided by conversion factor 6):

(a)

retention or retention-like or other refillable items with a capacity of less than 500 millilitres or more than 10 litres;

(b)

plates, foils or other non-fillable items of plastic or those in which the relationship between the contact area of such plastic items cannot be determined to the amount of food or nutritional supplement which is in contact with them. “

17. The following additives in Annex 2, Section A are inserted in corresponding numerical order:

Ref. No.

CAS No.

Name

Restrictions and/or specifications

(1)

(2)

(3)

(4)

"34850

34895

39680

42880

45600

45640

46700

46720

56535

59280

68078

69920

76866

85601

95000

143925-92-2

000088-68-6

000080-05-7

008001-79-4

003724-65-0

005232-99-5

004130-42-1

000100-97-0

027253-31-2

000144-62-7

028931-67-1

Bis(hydrated Talg-Alkyl)amine, oxidised

2-Aminobenzaamide

2.2-Bis(4-hydroxyphenyl)propan

Rizinus oil

Crotonic acid

2-Cyano-3,3-diphenylethylacrylate

5.7-Di-tert-butyl-3-(3,4- and 2.3dimethylphenyl)-3H-benzofuran-2-on containing: a) 5.7-Di-tert-butyl-3-(3,4-dimethylphenyl)-3H-benzofuran-2-on (80-100% w/w) and b) 5.7-Di-ter-butyl-3-(2,3-dimethylphenyl)-3H-benzofuran-(0-20 % w/w)

2.6-Di-tert-butyl-4-ethylphenol

esters of Glycerin with non-anic acid

Hexamethylentetramin

Cooperatives

Oxalic acid

Polyester of 1,2-proppandiol and/or 1.3-and/or 1.4-butandiol and/or polypropyleneglykol with adidipineic acid, including endemic acid, or C12-C18fatty acids, or n-Octanol and/or n-Decanol

Silicate, natural (excl. asbestos)

Trimethylolpropan, Triethacrylatmethyl-methacrylate, Copolymer

QM = only for use:

(a) in polyolefins of 0.1% (w/w), but not in LDPE when it comes to food, for which Annex 8 sets a reduction factor RF < 3

(b) in PET of 0.25 % (w/w) when it comes to contact with other food than those where the simulate proceeding is defined in Annex 8.

SML = 0.05 mg/kg. Only for use of PET for water and drink

SML(T) = 0.6 mg/kg (T)28)

QMA(T) = 0.05 mg/6 dm2 (b)33)

SML = 0.05 mg/kg

SML = 5 mg/kg

QMA = 4.8 mg/6 dm2

SML(T) = 15 mg/kg (T)22) (calculated as formaldehyd)

SML(T) = 0.05 mg/kg (calculated as neodecanic acid) and SML(T) = 0,05 mg/kg (14) (calculated as cognac). Not to use polymers in contact with food for which the simulate proceeding is defined in Annex 8

SML(T) = 6 mg/kg (29)

SML = 30 mg/kg

18. For the following additives in Section A, the contents of the column "Restrictions and/or specifications" as follows:

Ref. No.

CAS No.

Name

Restrictions and/or specifications

(1)

(2)

(3)

(4)

"45450

77895

068610-51-5

068439-49-6

p-Kresol-Dicyclopentadiene-Isobutylen, Copolymer

polyethyleneglykol (EO = 26)-monoalkyl (C16-C18) ether

SML = 5 mg/kg

SML = 0.05 mg/kg. The specifications in Annex 4 must be respected"

19. In Annex 2, Section A reference number 36640, column 4 is as follows:

"Only for use as a global agent. Use prohibited from 2 August 2005."

20. The following additives are deleted from Annex 2, Section A:

Ref. No.

CAS No.

Name

Restrictions and/or specifications

(1)

(2)

(3)

(4)

"565

67170

76865

85600

esters of Glycerin with non-anic acid

Mixing (80-100%) 5.7-Di-tert-butyl-3-(3,4-dimethyl-phenyl)-2(3H)benzofuranon and (0-20 Gew-%) 5.7-Di-tert-butyl-3-(2,3-dimethylphenyl)-2(3H)-benzofurn

Polyester of 1,2-proppandiol and/or 1.3- and/or 1.4-butandiol and/or polypropyleneglykol with adidipineic acid, including endemic acid, or C10-C18fatty acids, or n-Octanol and/or n-Decanol

Silikate, natural"

SML = 5 mg/kg

SML = 30 mg/kg

21. The following additives in Annex 2 Section B are inserted in corresponding numerical order:

Ref. No.

CAS No.

Name

Restrictions and/or specifications

(1)

(2)

(3)

(4)

"34650

38000

40720

46640

54880

55200

55280

55360

67896

71935

76680

86480

86920

86960

87120

94400

151841-65-5

000553-54-8

025013-16-5

000128-37-0

000050-0

001166-52-5

001034-01-1

000121-79-9

020336-96-3

007601-89-0

068132-00-3

007631-90-5

007632-00-0

007757-83-7

007772-98-7

036443-68-2

Aluminiumhydroxybis [2.2'-methylenbis(4.6-di-tert-butylphenyl) phosphate

Lithiumbenzoat

Tert-butyl-4-hydroxyanisol (= BHA)

2.6-Di-tert-butyl-p-kresol (= BHT)

Formaldehyde

Dodecylgallat

Octylgallat

Propylgallat

Lithiummyristat

Sodium perchlorate monohydrate

Hydrogenated polycyclopentadiene

Sodium bisulfit

Sodium starch

Sodium sulphite

Sodium sulfate

Trimethylenglykol-bis[3-(3-tert-butyl-4-hydroxy-5-methylphenyl)propionate]

SML = 5 mg/kg

SML(T) = 0.6 mg/kg (T)8) (calculated as lithium)

SML = 30 mg/kg

SML = 3.0 mg/kg

SML(T) = 15 mg/kg (T)22)

SML(T) = 30 mg/kg (T)34)

SML(T) = 30 mg/kg (T)34)

SML(T) = 30 mg/kg (T)34)

SML(T) = 0.6 mg/kg (T)8) (calculated as lithium)

SML = 0.05 mg/kg (31)

SML = 5 mg/kg (1)

SML(T) = 10 mg/kg (T)30) (calculated as SO2)

SML = 0.6 mg/kg

SML(T) = 10 mg/kg (T)30) (calculated as SO2)

SML(T) = 10 mg/kg (T)30) (calculated as SO2)

SML = 9 mg/kg

22. The following additives are removed from Annex 2, Section B:

Ref. No.

CAS No.

Name

Restrictions and/or specifications

(1)

(2)

(3)

(4)

"46720

68078

95000

004130-42-1

027253-31-2

028931-67-1

2.6-Di-tert-butyl-4-ethylphenol

Cooperatives

Trimethylolpropan-trimethacry-lat-methyl-methacrylate-Copoly-mer"

QMA = 4.8 mg/6 dm2

SML(T) = 0.05 mg/kg (calculated as neodecanic acid) and SML(T) = 0,05 mg/kg (14) (calculated as cognac). Not to use polymers in contact with food for which the simulate proceeding is defined in Annex 8

23. Annex 3 is:

"PRODUKTE, THE DURCH BAKTERIELLE FERMENT OF WONNEN

Ref. No.

CAS No.

Name

Restrictions and/or specifications

(1)

(2)

(3)

(4)

18888

080181-31-3

3-Hydroxy butteric acid, 3-Hydroxyvalerianic acid copolymer

The specifications in Annex 4 must be respected"

24. In Annex 4, the specifications for refer-Nos 16690 and 18888 are as follows:

Ref. No.

SPECIFICATIONS

"16690

Divinylbenzol

Can contain up to 45% of Ethylvinylbenzol

18888

3-Hydroxy butteric acid-3-Hydroxyvalerianic acid copolymer

Definition Copolymers are controlled by Alcaligenes Fermentation

eutrophus, with mixtures of glucose and propionic acid

as carbon sources. The organism used

has not been derived from genetic engineering, but is derived from a

only wild strain of Alcaligene eutrophus (H16 NCIMB10442).

The starting sponges are stored in ampoules.

Based on the main sponges, parts for production

produced in liquid nitrogen. They serve

Manufacture of vaccines for piglets. Samples from

Fermenter will be microscopic daily and in relation to morpho

logical changes in the colonies on different nutrient floors

at various temperatures. Copolymers will

from heat-treated bacteria through controlled digestion

other cell components, washing and drying. The

Copolymers are usually made up of melting

tes granulates with additives such as crystal-rich means,

plasticizers, fillers, stabilisers and pigments offered

all conform to the general and special specifications

Chemicals

Poly(3-D-hydroxybutyrat-co-3-D-hydroxyvalerianate)

CAS No 080181-31-3

Structural design CH3

I

CH3 O CH2O

I I I I I

(-O-CH2-C-)m-(O-CH2-C)

more than 0 and less than 0.25

Average at least 150 000 Dalton (measured by gel-permeation

Molecular weight chromatography

salary determination at least 98% Poly(3-D-Hydroxybutyrat-co-3-D-hydroxyvalerianate),

calculated by hydrolysis as a mixture of 3D-Hydroxy butteric acid and

3-D-Hydroxyvalerian Acid

Description After insulation of white to cream powder

Characteristics

Identification

Audits

solubility in chlorine hydrocarbons (e.g. chloroform, thylormethane),

However, practically insoluble in ethanol, aliphatic alkans and water

Limit QMA for Crotonic acid is 0.05 mg/6 dm2

purity Before granulating, the raw material (Copolymer powder) can be maintained

ten.

- Nitrogen maximum of 2 500 mg/kg plastic

— zinc maximum 100 mg/kg plastic

copper maximum 5 mg/kg plastic

— Lead maximum of 2 mg/kg plastic

– Arsen up to 1 mg/kg plastic

- chromium not more than 1 mg/kg plastic

25. In Annex 4, the following specifications for Ref.-No. 11530 and 77895 are inserted:

Ref. No.

SPECIFICATIONS

"11530

2-Hydroxypropylacrylate

Can up to 25% (w/w)-2-Hydroxyisopropylacrylate (CAS No 002918-23-2)

77895

polyethyleneglykol(EO = 2-6)-monoalkyl (C16-C18)-ether

The mix is as follows:

– polyethyleneglykol(EO = 26)-monoalkyl (C16-C18)-ether (about 28 %)

— Fat alcohol (C16-C18) (about 48%)

— Ethylenglykolmonoalkyl (C16-C18)-ether (about 24 %)

26. Annex 5 is:

‘ANMERGERMANY’ REQUIREMENTS AND/OR SPECIFICATION

(b)1) Warning: The SML could be exceeded in fatty food simulate matter.

(b)2) SML(T) in this particular case means that the restriction cannot be exceeded by the sum of theswerte values of the following substances indicated by their Ref. No.: 10060 and 23920.

(b)3) SML(T) in this particular case means that the restriction cannot be exceeded by the sum of theswerte values of the following substances indicated by its Ref. No.: 15760, 16990, 47680, 53650 and 89440.

(b)4) SML(T) in this particular case means that the restriction cannot be exceeded by the sum of theswerte values of the following substances indicated with its reference No: 19540, 19960 and 64800.

(b)5) SML(T) in this particular case means that the restriction cannot be exceeded by the sum of theswerte values of the following substances indicated by its Ref. No.: 14200, 14230 and 41840.

(b)6) SML(T) in this particular case means that the limitation cannot be exceeded by the sum of theswerte values of the following substances indicated by its Ref. No.: 66560 and 66580.

(b)7) SML(T) in this particular case means that the limitation cannot be exceeded by the sum of theswerte values of the following substances indicated by its Ref. No.: 30080, 42320, 45195, 45200, 53610, 81760, 89200 and 92030.

(b)8) SML(T) in this particular case means that the limitation cannot be exceeded by the sum of theswerte values of the following substances indicated with its Ref. No.: 38000, 42400, 64320, 67896, 73040, 85760, 85840, 85920 and 95725.

(b)9) Warning: There is a risk that the migration of the substance affects the organoleptic properties of the food and thus does not affect the finished product. 1 lit. (c) of Regulation (EC) No. 1935/2004.

(b)10) SML(T) in this particular case means that the limitation cannot be exceeded by the sum of theswerte values of the following substances indicated by its Ref. No.: 30180, 40980, 63200, 65120, 65120, 65280, 65360, 65440 and 73120.

(b)11) SML(T) in this particular case means that the restriction cannot be exceeded by the sum of the migration values (as calculated as Iod) of the following substances indicated by reference No: 45200, 64320, 81680 and 86800.

(b)12) SML(T) in this particular case means that the restriction cannot be exceeded by the sum of theswerte values of the following substances indicated by its Ref. No.: 36720, 36800, 36840 and 92000.

(b)13) SML(T) in this particular case means that the restriction cannot be exceeded by the sum of theswerte values of the following substances indicated by their Ref. No.: 39090 and 39120.

(b)14) SML(T) in this particular case means that the restriction cannot be exceeded by the sum of theswerte values of the following substances indicated with its reference No: 44960, 68078, 82020 and 89170.

(b)15) SML(T) in this particular case means that the restriction cannot be exceeded by the sum of the migration values of the following substances indicated by its reference No: 15970, 48640, 48720, 48880, 61280, 61360 and 61600.

(b)16) SML(T) in this particular case means that the restriction cannot be exceeded by the sum of theswerte values of the following substances indicated by its reference No: 49600, 67520 and 83599.

(b)17) SML(T) in this particular case means that the restriction cannot be exceeded by the sum of the migration values of the following substances indicated with its reference No: 50160, 50240, 50320, 50360, 50400, 50480, 50560, 50640, 50720, 50800, 50880, 50960, 51040 and 51120.

(b)18) SML(T) in this particular case means that the restriction cannot be exceeded by the sum of theswerte values of the following substances indicated by its Ref. No.: 67600, 67680 and 67760.

(b)19) SML(T) in this particular case means that the restriction cannot be exceeded by the sum of theswerte values of the following substances indicated by its Ref. No.: 60400, 60480 and 61440.

(b)20) SML(T) in this particular case means that the restriction cannot be exceeded by the sum of theswerte values of the following substances, as indicated in the reference No: 66400 and 66480.

(b)21) SML(T) in this particular case means that the restriction cannot be exceeded by the sum of theswerte values of the following substances indicated by their Ref. No.: 93120 and 93280.

(b)22) SML(T) in this particular case means that the restriction cannot be exceeded by the sum of theswerte values of the following substances indicated by its Ref. No.: 17260, 18670, 54880 and 59280.

(b)23) SML(T) in this particular case means that the limitation cannot be exceeded by the sum of theswerte values of the following substances indicated by its Ref. No.: 13620, 36840, 40320 and 87040.

(b)24) SML(T) in this particular case means that the restriction cannot be exceeded by the sum of theswerte values of the following substances, as indicated in the reference No: 13720 and 40580.

(b)25) SML(T) in this particular case means that the limitation cannot be exceeded by the sum of theswerte values of the following substances indicated by its reference No: 16650 and 51570.

(b)26) QM(T) in this particular case means that the restriction cannot be exceeded by the sum of the remaining quantities of the following substances indicated with its reference No: 14950, 15700, 16240, 16570, 16570, 16600, 16630, 18640, 19110, 22332, 22420, 22570, 25210, 25240 and 25270.

(b)27) QMA(T) in this particular case means that the restriction cannot be exceeded by the sum of the remaining quantities of the following substances indicated by its Ref. No.: 10599/90A, 10599/91, 10599/92A and 10599/93.

(b)28) SML(T) in this particular case means that the limitation cannot be exceeded by the sum of theswerte values of the following substances indicated by its Ref. No.: 13480 and 39680.

(b)29) SML(T) in this particular case means that the restriction cannot be exceeded by the sum of theswerte values of the following substances indicated by its Ref. No.: 22775 and 69920.

(b)30) SML(T) in this particular case means that the restriction cannot be exceeded by the sum of theswerte values of the following substances, as indicated in the reference No: 86480, 86960 and 87120.

(b)31) Conformity tests in contact with fat should be carried out using saturated fat simulate matter solutions as a simulate solution D.

(b)32) Conformity tests in contact with fat should be carried out using Isoctan due to instability of the substance in Simulance Solution D.

(b)33) QMA(T) in this particular case means that the restriction cannot be exceeded by the sum of the remaining quantities of the following substances indicated by its Ref. No.: 14800 and 45600.

(b)34) SML(T) in this particular case means that the restriction cannot be exceeded by the sum of theswerte values of the following substances indicated with their Ref. No.: 55200, 55280 and 55360."

27. Annex 11 is deleted.

Smoke-Kallat